Open Source Ecology - User contributions [en]

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-13T17:03:14Z

Ty Ross: /* Mon May 12th, 2014 */

=Mon May 12th, 2014=
[[File:CNC Table Assembly.STP]],
[[File:CNC Table Assembly (AP203 STEP).STEP]],
Solidworks- [[File:CNC Table Assembly.zip]]

'''CNC Table Model Notes'''
* When converted to .stp and opened in Freecad or Sketchup, part numbers are lost. We’ll need to see if there is a setting for this or a property in SolidWorks that we can change to make this translate properly. Otherwise a drawing with BOM will need to be created in SolidWorks and then exported.
* x axis shoulder screw with spring being used to tension motor mount to gantry not modelled. Could not find part and looks like a better design could be made.
* Tool mount not modeled, will require significant modification to accommodate plasma, router and height sensing equipment.
* Some of the geometry in the motor mount is not required and could be simplified for fabrication.
* Some of the threaded fasteners on the motor mount could be replaced with bolt assy’s to avoid tapping holes.
* 2” driveshaft does not reach the gear to the rack in the model. On the existing table, the gear is offset off the end of the driveshaft. longer driveshaft should be used.
* The gear that engages the rack in the model is space claim only. Could not find an off the shelf component to match. As we have discussed going to a 1/2” rack instead of the existing 1/4” in the future, an off the shelf 1/2” gear to match can be found from McMaster Carr.
* The models for the reducing belt pulleys were generated through the product configurator off of Misumi.com. They did not come out accurate to what was input. I’ve modified the model for fit/form/function, but source of supply should be verified.
* Model does not have any of the base structure as that has already been modelled in Sketchup and is subject to change. Once the drive control/height control system is proved out on this table, we can either decide to keep the base structure or change to the grid beam configuration.

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-13T17:01:29Z

Ty Ross: /* Tuesday May 6, 2014 */

=Mon May 12th, 2014=
[[File:CNC Table Assembly.STP]]
[[File:CNC Table Assembly (AP203 STEP).STEP]]
Solidworks- [[File:CNC Table Assembly.zip]]

'''CNC Table Model Notes'''
* When converted to .stp and opened in Freecad or Sketchup, part numbers are lost. We’ll need to see if there is a setting for this or a property in SolidWorks that we can change to make this translate properly. Otherwise a drawing with BOM will need to be created in SolidWorks and then exported.
* x axis shoulder screw with spring being used to tension motor mount to gantry not modelled. Could not find part and looks like a better design could be made.
* Tool mount not modeled, will require significant modification to accommodate plasma, router and height sensing equipment.
* Some of the geometry in the motor mount is not required and could be simplified for fabrication.
* Some of the threaded fasteners on the motor mount could be replaced with bolt assy’s to avoid tapping holes.
* 2” driveshaft does not reach the gear to the rack in the model. On the existing table, the gear is offset off the end of the driveshaft. longer driveshaft should be used.
* The gear that engages the rack in the model is space claim only. Could not find an off the shelf component to match. As we have discussed going to a 1/2” rack instead of the existing 1/4” in the future, an off the shelf 1/2” gear to match can be found from McMaster Carr.
* The models for the reducing belt pulleys were generated through the product configurator off of Misumi.com. They did not come out accurate to what was input. I’ve modified the model for fit/form/function, but source of supply should be verified.
* Model does not have any of the base structure as that has already been modelled in Sketchup and is subject to change. Once the drive control/height control system is proved out on this table, we can either decide to keep the base structure or change to the grid beam configuration.

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

Tyler Ross Log

2014-05-12T16:44:25Z

Ty Ross: /* Mon May 5th, 2014 */

=Mon May 12th, 2014=
Leaving FeF today. Uploaded 3D Model of the existing torch table with notes.
.IGS and .zip were both too large to upload. Uploaded to Dropbox instead and sent link to Marcin.

=Mon May 5th, 2014=
* Populate CNC Torch Table with known OS CNC machines. (Devin will continue research and follow up with these projects.)
* CAD model existing CNC table in Solidworks, export .stp to sketch up/freecad to be accessed by community.
* Start looking at existing drive mounts and consider modification for better alignment.

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-12T16:02:22Z

Ty Ross: /* Tuesday May 6, 2014 */

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STP]]
Solidworks- [[File:CNC Table Assembly.zip]]

Mon May 12th, 2014 CNC Table Model Notes
* When converted to .stp and opened in Freecad or Sketchup, part numbers are lost. We’ll need to see if there is a setting for this or a property in SolidWorks that we can change to make this translate properly. Otherwise a drawing with BOM will need to be created in SolidWorks and then exported.
* x axis shoulder screw with spring being used to tension motor mount to gantry not modelled. Could not find part and looks like a better design could be made.
* Tool mount not modeled, will require significant modification to accommodate plasma, router and height sensing equipment.
* Some of the geometry in the motor mount is not required and could be simplified for fabrication.
* Some of the threaded fasteners on the motor mount could be replaced with bolt assy’s to avoid tapping holes.
* 2” driveshaft does not reach the gear to the rack in the model. On the existing table, the gear is offset off the end of the driveshaft. longer driveshaft should be used.
* The gear that engages the rack in the model is space claim only. Could not find an off the shelf component to match. As we have discussed going to a 1/2” rack instead of the existing 1/4” in the future, an off the shelf 1/2” gear to match can be found from McMaster Carr.
* The models for the reducing belt pulleys were generated through the product configurator off of Misumi.com. They did not come out accurate to what was input. I’ve modified the model for fit/form/function, but source of supply should be verified.
* Model does not have any of the base structure as that has already been modelled in Sketchup and is subject to change. Once the drive control/height control system is proved out on this table, we can either decide to keep the base structure or change to the grid beam configuration.

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-12T16:01:35Z

Ty Ross: /* Tuesday May 6, 2014 */

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STP]]
Solidworks- [[File:CNC Table Assembly.zip]]

Mon May 12th, 2014 CNC Table Model Notes

* When converted to .stp and opened in Freecad or Sketchup, part numbers are lost. We’ll need to see if there is a setting for this or a property in SolidWorks that we can change to make this translate properly. Otherwise a drawing with BOM will need to be created in SolidWorks and then exported.
* x axis shoulder screw with spring being used to tension motor mount to gantry not modelled. Could not find part and looks like a better design could be made.
* Tool mount not modeled, will require significant modification to accommodate plasma, router and height sensing equipment.
* Some of the geometry in the motor mount is not required and could be simplified for fabrication.
* Some of the threaded fasteners on the motor mount could be replaced with bolt assy’s to avoid tapping holes.
* 2” driveshaft does not reach the gear to the rack in the model. On the existing table, the gear is offset off the end of the driveshaft. longer driveshaft should be used.
* The gear that engages the rack in the model is space claim only. Could not find an off the shelf component to match. As we have discussed going to a 1/2” rack instead of the existing 1/4” in the future, an off the shelf 1/2” gear to match can be found from McMaster Carr.
* The models for the reducing belt pulleys were generated through the product configurator off of Misumi.com. They did not come out accurate to what was input. I’ve modified the model for fit/form/function, but source of supply should be verified.
* Model does not have any of the base structure as that has already been modelled in Sketchup and is subject to change. Once the drive control/height control system is proved out on this table, we can either decide to keep the base structure or change to the grid beam configuration.

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

File:CNC Table Assembly.IGS

2014-05-12T15:53:21Z

Ty Ross:

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-12T15:51:46Z

Ty Ross: /* Tuesday May 6, 2014 */

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STP]]
[[File:CNC Table Assembly.IGS]]
Solidworks- [[File:CNC Table Assembly.zip]]

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-12T15:27:13Z

Ty Ross: /* Tuesday May 6, 2014 */

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STP]]

Solidworks- [[File:CNC Table Assembly.zip]]

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

File:CNC Table Assembly.STP

2014-05-06T14:31:44Z

Ty Ross:

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-06T14:28:55Z

Ty Ross:

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STP]]

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-06T14:15:41Z

Ty Ross:

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STEP]]

=Tuesday Dec 3, 2013=
From [[Samthetechie Log]]:
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-06T14:15:16Z

Ty Ross:

=Tuesday May 6, 2014=
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STEP]]

From [[Samthetechie Log]]:
=Tuesday Dec 3, 2013=
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

File:CNC Table Assembly.STEP

2014-05-06T14:13:44Z

Ty Ross:

CNC Torch-Router Table 2 - Overall Machine - 3D CAD

2014-05-06T14:12:54Z

Ty Ross: /* Tuesday May 6th, 2014 */

From [[Samthetechie Log]]:

=Tuesday May 6, 2014+
*Modeled existing torch table. Motors and mounting plates still need to be added.
[[File:CNC Table Assembly.STEP]]

=Tuesday Dec 3, 2013=
* Looked at the new controller electronics that arrived in the post from Lasersaur
* Looked at the current wiring / config of the torch table.
* Made some fresh mesurements on the table and cleaned up my initial Sketchup/CAD models, first version ready for publishing to wiki (note still quite crude, lacks z axis detail): [[File:CNCTorchTable.skp]]
[[Image:CNCTorchTable_top.png|600px]]
[[Image:CNCTorchTable.png|600px]]
[[Image:CNCTorchTable_bottom.png|600px]]
[[Image:CNCTorchTable_iso_bottom.png|600px]]

Tyler Ross Log

2014-05-05T15:36:53Z

Ty Ross: Created page with "=Mon May 5th, 2014= * Populate CNC Torch Table with known OS CNC machines. (Devin will continue research and follow up with these projects.) * CAD model existing CNC table in ..."

=Mon May 5th, 2014=
* Populate CNC Torch Table with known OS CNC machines. (Devin will continue research and follow up with these projects.)
* CAD model existing CNC table in Solidworks, export .stp to sketch up/freecad to be accesses by community.
* Start looking at existing drive mounts and consider modification for better alignment.

CNC Torch-Router Table 2 - Team

2014-05-05T15:32:27Z

Ty Ross: /* Other DIY/OS Work */

*[[Chuck Log]]
*[[Paul Log]]
*[[Tyler Ross Log]]
*[[Anthony Log]]
*[[Devin Log]]
*[[Marcin Log]]
*[[Max Log]]
*[[Yann Log]]
*[[Samthetechie Log]]
*[[Dan Log]]

=Other DIY/OS Work=
*Marcelo Delmero - [http://flamecut.marcelodelnero.com.br FlameCut CNC]
*Kikori OS CNC Router Table - [http://www.sindrianarts.com/category/cnc-machines/building-machines/ Kikori CNC Router]
*Plasma cutter - with a lot of custom cnc cut parts
*Plasma cutter - Velocar collaborators

=Team Survey=

Fill this survey if you are a team member. This allows everyone on the team to communicate with one another via email - and shows the skill set of people involved

=Survey Results=

CNC Torch-Router Table 2 - Team

2014-05-05T15:28:24Z

Ty Ross: /* Other DIY/OS Work */

*[[Chuck Log]]
*[[Paul Log]]
*[[Tyler Ross Log]]
*[[Anthony Log]]
*[[Devin Log]]
*[[Marcin Log]]
*[[Max Log]]
*[[Yann Log]]
*[[Samthetechie Log]]
*[[Dan Log]]

=Other DIY/OS Work=
*Marcelo Delmero - [http://flamecut.marcelodelnero.com.br link title]
*Plasma cutter - with a lot of custom cnc cut parts
*Plasma cutter - Velocar collaborators

=Team Survey=

Fill this survey if you are a team member. This allows everyone on the team to communicate with one another via email - and shows the skill set of people involved

=Survey Results=

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:22:13Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accommodate mounting of height sensor.
* For CNC routing
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
** Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:21:41Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
* For CNC routing
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
** Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:21:20Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
For CNC routing
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
** Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:21:02Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
For CNC routing:
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
**Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:20:42Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
For CNC routing:
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
**Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:19:56Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
For CNC routing:
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
* Allow for wrench access to the collet.
* Attachment point for a vacuum hose.
* Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:17:29Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
For CNC routing:
* Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
** Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T20:16:46Z

Ty Ross:

* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router.
* Base of the wood router is significantly larger footprint than that of the torch or plasma head, this will need to be accounted for.
* Suggesting an adaptable design with configurable base plate that can be matched to whatever router you want to use, and mounts to the vertical shaft.
* Adaptable to wider gantry plate if tooling requires it to be thicker for rigidity.
* Accomodate mounting of height sensor.
For CNC routing:
** Base plate will need to divert the air blowing out of the router (so it doesn’t blow dust everywhere).
** Allow for wrench access to the collet.
** Attachment point for a vacuum hose.
** Removable brush shroud.

CNC Torch and Router Table 2 - Working Tool Holder - Requirements

2014-05-02T19:56:29Z

Ty Ross: Created page with "* Tool holder will need to be adaptable to hold oxy/acetylene torch, Plasma cutter, and router. * Base of the wood router is significantly larger footprint than that of the t..."

CNC Torch and Router Table - Universal Tool Holder Development Board

2014-05-02T17:23:28Z

Ty Ross:

<html><iframe width=100% height='500' frameborder='0' src='https://docs.google.com/spreadsheet/pub?key=0ArxMgIRnZVgMdFZZdFF2WUpWcnN3a2IycDdTVW0tenc&output=html&widget=true'></iframe></html>

[https://docs.google.com/spreadsheet/ccc?key=0ArxMgIRnZVgMdFZZdFF2WUpWcnN3a2IycDdTVW0tenc#gid=1 edit]

CNC Torch and Router Table - Gas Flow and Control Development Board

2014-05-02T17:07:51Z

Ty Ross:

<html><iframe width=100% height='500' frameborder='0' src='https://docs.google.com/spreadsheet/pub?key=0ArxMgIRnZVgMdDNrOGZ3STd5OHNUMDExaG5jS3Y3RFE&output=html&widget=true'></iframe></html>

[https://docs.google.com/spreadsheet/ccc?key=0ArxMgIRnZVgMdDNrOGZ3STd5OHNUMDExaG5jS3Y3RFE#gid=1 edit]

CNC Torch and Router Table - Gas Flow and Control Development Board

2014-05-02T17:05:28Z

Ty Ross:

<html><iframe width=100% height='500' frameborder='0' src='https://docs.google.com/spreadsheet/pub?key=0ArpE5Y9PpJCXdDlMS055d0duSFFYejgxRVRKaWsxVEE&output=html&widget=true'></iframe></html>

[https://docs.google.com/spreadsheet/ccc?key=0ArxMgIRnZVgMdDNrOGZ3STd5OHNUMDExaG5jS3Y3RFE#gid=1 edit]

Tyler Log

2014-04-08T15:13:01Z

Ty Ross: Created page with "=Tues April 08, 2014= Created OSE wiki account and log page."

=Tues April 08, 2014=

Created OSE wiki account and log page.