G01 S1; endstops
G01 E0; no extrusion
G21; millimeters
G91 G0 F300.0 Z20.000; pen park !!Zsafe
G90; absolute
G28 X; home = 0
G28 Y; home = 145ish
G28 Z; home = 0
G29 ; level bed - sensor only sees metal, think about where it gets its points.
G00 F300.0 Z20.000; pen park !!Zpark
G00 F2400.0 Y20.000; !!Ybottom - sight offset for home - this assures that later you can move the drill to this position.  if start at 0,0 drill bit cannot get to that position. (drill y cooridiante will be negative)
G00 F2400.0 X0.000; !!Xleft
G00 F300.0 Z3.000; pen down 
M0 ;pause 1 - insert pen manually adjust here with cmd line gcode to get height correct.  
;Want to leave a small amount of room for z-axis to move down 
;after pen is clamped for good contact with paper etc.
;G00 F300.0 Z3.00; pen down to 3 reference - in full contact with workarea.
;G92 Z0 ;z- set 3.00 to now be 0 to keep drill out of work area.
G00 F300.0 Z5.000; pen up !!Zup - draw a test mark
G00 F300.0 Z0.000; pen down !!Zwork
G00 F300.0 Z5.000; pen up !!Zup
G00 F300.0 Z0.000; pen down !!Zwork
G00 F300.0 Z20.000; pen up !!Zup
M0 ;pause 2- verify correct marks at home zero - will use these to adjust offset of mill bit later
;on resume - do drawing
G00 F2400.0 X66.957 Y62.556; move !!Xleft+66.957 Ybottom+62.556
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X70.767 Y62.556; draw !!Xleft+70.767 Ybottom+62.556
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.147 Y62.556; move !!Xleft+63.147 Ybottom+62.556
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.177 Y62.556; draw !!Xleft+49.177 Ybottom+62.556
G01 F600.0 X49.177 Y49.856; draw !!Xleft+49.177 Ybottom+49.856
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X56.797 Y54.936; move !!Xleft+56.797 Ybottom+54.936
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X63.147 Y54.936; draw !!Xleft+63.147 Ybottom+54.936
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X56.797 Y49.856; move !!Xleft+56.797 Ybottom+49.856
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X51.717 Y49.856; draw !!Xleft+51.717 Ybottom+49.856
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.177 Y39.696; move !!Xleft+49.177 Ybottom+39.696
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.177 Y49.856; draw !!Xleft+49.177 Ybottom+49.856
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.327 Y36.032; move !!Xleft+49.327 Ybottom+36.032
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X48.489 Y35.195; draw !!Xleft+48.489 Ybottom+35.195
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X48.864 Y34.862; move !!Xleft+48.864 Ybottom+34.862
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.713 Y35.711; draw !!Xleft+49.713 Ybottom+35.711
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.780 Y35.444; move !!Xleft+49.780 Ybottom+35.444
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.768 Y35.566; draw !!Xleft+49.768 Ybottom+35.566
G01 F600.0 X49.729 Y35.683; draw !!Xleft+49.729 Ybottom+35.683
G01 F600.0 X49.667 Y35.791; draw !!Xleft+49.667 Ybottom+35.791
G01 F600.0 X49.583 Y35.886; draw !!Xleft+49.583 Ybottom+35.886
G01 F600.0 X49.481 Y35.964; draw !!Xleft+49.481 Ybottom+35.964
G01 F600.0 X49.364 Y36.022; draw !!Xleft+49.364 Ybottom+36.022
G01 F600.0 X49.238 Y36.057; draw !!Xleft+49.238 Ybottom+36.057
G01 F600.0 X49.106 Y36.069; draw !!Xleft+49.106 Ybottom+36.069
G01 F600.0 X48.975 Y36.057; draw !!Xleft+48.975 Ybottom+36.057
G01 F600.0 X48.848 Y36.022; draw !!Xleft+48.848 Ybottom+36.022
G01 F600.0 X48.732 Y35.964; draw !!Xleft+48.732 Ybottom+35.964
G01 F600.0 X48.630 Y35.886; draw !!Xleft+48.630 Ybottom+35.886
G01 F600.0 X48.546 Y35.791; draw !!Xleft+48.546 Ybottom+35.791
G01 F600.0 X48.483 Y35.683; draw !!Xleft+48.483 Ybottom+35.683
G01 F600.0 X48.445 Y35.566; draw !!Xleft+48.445 Ybottom+35.566
G01 F600.0 X48.432 Y35.444; draw !!Xleft+48.432 Ybottom+35.444
G01 F600.0 X48.445 Y35.322; draw !!Xleft+48.445 Ybottom+35.322
G01 F600.0 X48.483 Y35.205; draw !!Xleft+48.483 Ybottom+35.205
G01 F600.0 X48.546 Y35.097; draw !!Xleft+48.546 Ybottom+35.097
G01 F600.0 X48.630 Y35.002; draw !!Xleft+48.630 Ybottom+35.002
G01 F600.0 X48.732 Y34.924; draw !!Xleft+48.732 Ybottom+34.924
G01 F600.0 X48.848 Y34.867; draw !!Xleft+48.848 Ybottom+34.867
G01 F600.0 X48.975 Y34.831; draw !!Xleft+48.975 Ybottom+34.831
G01 F600.0 X49.106 Y34.819; draw !!Xleft+49.106 Ybottom+34.819
G01 F600.0 X49.238 Y34.831; draw !!Xleft+49.238 Ybottom+34.831
G01 F600.0 X49.364 Y34.867; draw !!Xleft+49.364 Ybottom+34.867
G01 F600.0 X49.481 Y34.924; draw !!Xleft+49.481 Ybottom+34.924
G01 F600.0 X49.583 Y35.002; draw !!Xleft+49.583 Ybottom+35.002
G01 F600.0 X49.667 Y35.097; draw !!Xleft+49.667 Ybottom+35.097
G01 F600.0 X49.729 Y35.205; draw !!Xleft+49.729 Ybottom+35.205
G01 F600.0 X49.768 Y35.322; draw !!Xleft+49.768 Ybottom+35.322
G01 F600.0 X49.780 Y35.444; draw !!Xleft+49.780 Ybottom+35.444
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.177 Y39.696; move !!Xleft+49.177 Ybottom+39.696
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X101.247 Y39.696; draw !!Xleft+101.247 Ybottom+39.696
G01 F600.0 X101.247 Y53.666; draw !!Xleft+101.247 Ybottom+53.666
G01 F600.0 X101.247 Y60.016; draw !!Xleft+101.247 Ybottom+60.016
G01 F600.0 X101.247 Y63.826; draw !!Xleft+101.247 Ybottom+63.826
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X101.247 Y70.175; move !!Xleft+101.247 Ybottom+70.175
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X101.247 Y63.826; draw !!Xleft+101.247 Ybottom+63.826
G01 F600.0 X77.117 Y63.826; draw !!Xleft+77.117 Ybottom+63.826
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X87.277 Y67.635; move !!Xleft+87.277 Ybottom+67.635
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X83.467 Y67.635; draw !!Xleft+83.467 Ybottom+67.635
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.767 Y60.016; move !!Xleft+70.767 Ybottom+60.016
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X73.307 Y60.016; draw !!Xleft+73.307 Ybottom+60.016
G01 F600.0 X77.117 Y63.826; draw !!Xleft+77.117 Ybottom+63.826
G01 F600.0 X80.927 Y67.635; draw !!Xleft+80.927 Ybottom+67.635
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.767 Y57.476; move !!Xleft+70.767 Ybottom+57.476
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X77.117 Y57.476; draw !!Xleft+77.117 Ybottom+57.476
G01 F600.0 X78.387 Y58.746; draw !!Xleft+78.387 Ybottom+58.746
G01 F600.0 X80.927 Y58.746; draw !!Xleft+80.927 Ybottom+58.746
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X89.817 Y60.016; move !!Xleft+89.817 Ybottom+60.016
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X88.547 Y58.746; draw !!Xleft+88.547 Ybottom+58.746
G01 F600.0 X80.927 Y58.746; draw !!Xleft+80.927 Ybottom+58.746
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X101.247 Y60.016; move !!Xleft+101.247 Ybottom+60.016
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X94.816 Y60.016; draw !!Xleft+94.816 Ybottom+60.016
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X101.247 Y53.666; move !!Xleft+101.247 Ybottom+53.666
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X94.816 Y53.666; draw !!Xleft+94.816 Ybottom+53.666
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X80.927 Y53.846; move !!Xleft+80.927 Ybottom+53.846
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X89.636 Y53.846; draw !!Xleft+89.636 Ybottom+53.846
G01 F600.0 X89.817 Y53.666; draw !!Xleft+89.817 Ybottom+53.666
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X78.207 Y53.846; move !!Xleft+78.207 Ybottom+53.846
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X80.927 Y53.846; draw !!Xleft+80.927 Ybottom+53.846
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X77.117 Y54.936; move !!Xleft+77.117 Ybottom+54.936
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X78.207 Y53.846; draw !!Xleft+78.207 Ybottom+53.846
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.767 Y54.936; move !!Xleft+70.767 Ybottom+54.936
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X77.117 Y54.936; draw !!Xleft+77.117 Ybottom+54.936
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.147 Y57.476; move !!Xleft+63.147 Ybottom+57.476
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X66.957 Y57.476; draw !!Xleft+66.957 Ybottom+57.476
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X66.957 Y62.556; move !!Xleft+66.957 Ybottom+62.556
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X66.957 Y57.476; draw !!Xleft+66.957 Ybottom+57.476
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X87.277 Y93.035; move !!Xleft+87.277 Ybottom+93.035
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X66.957 Y93.035; draw !!Xleft+66.957 Ybottom+93.035
G01 F600.0 X66.957 Y62.556; draw !!Xleft+66.957 Ybottom+62.556
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X101.247 Y80.335; move !!Xleft+101.247 Ybottom+80.335
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X101.247 Y82.875; draw !!Xleft+101.247 Ybottom+82.875
G01 F600.0 X101.247 Y93.035; draw !!Xleft+101.247 Ybottom+93.035
G01 F600.0 X87.277 Y93.035; draw !!Xleft+87.277 Ybottom+93.035
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X87.277 Y79.065; move !!Xleft+87.277 Ybottom+79.065
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X87.277 Y93.035; draw !!Xleft+87.277 Ybottom+93.035
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X87.277 Y79.065; move !!Xleft+87.277 Ybottom+79.065
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X80.927 Y79.065; draw !!Xleft+80.927 Ybottom+79.065
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X75.847 Y79.065; move !!Xleft+75.847 Ybottom+79.065
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X73.307 Y79.065; draw !!Xleft+73.307 Ybottom+79.065
G01 F600.0 X72.037 Y77.795; draw !!Xleft+72.037 Ybottom+77.795
G01 F600.0 X70.767 Y77.795; draw !!Xleft+70.767 Ybottom+77.795
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X69.243 Y82.875; move !!Xleft+69.243 Ybottom+82.875
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X70.513 Y81.605; draw !!Xleft+70.513 Ybottom+81.605
G01 F600.0 X70.767 Y81.605; draw !!Xleft+70.767 Ybottom+81.605
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X64.742 Y82.875; move !!Xleft+64.742 Ybottom+82.875
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.177 Y82.875; draw !!Xleft+49.177 Ybottom+82.875
G01 F600.0 X49.177 Y62.556; draw !!Xleft+49.177 Ybottom+62.556
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.177 Y89.225; move !!Xleft+49.177 Ybottom+89.225
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.177 Y82.875; draw !!Xleft+49.177 Ybottom+82.875
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.177 Y89.225; move !!Xleft+49.177 Ybottom+89.225
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X49.327 Y89.378; draw !!Xleft+49.327 Ybottom+89.378
G01 F600.0 X64.742 Y89.378; draw !!Xleft+64.742 Ybottom+89.378
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X69.243 Y89.378; move !!Xleft+69.243 Ybottom+89.378
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X69.243 Y89.225; draw !!Xleft+69.243 Ybottom+89.225
G01 F600.0 X70.767 Y87.701; draw !!Xleft+70.767 Ybottom+87.701
G01 F600.0 X70.767 Y81.605; draw !!Xleft+70.767 Ybottom+81.605
G01 F600.0 X70.767 Y77.795; draw !!Xleft+70.767 Ybottom+77.795
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.767 Y75.255; move !!Xleft+70.767 Ybottom+75.255
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X101.247 Y75.255; draw !!Xleft+101.247 Ybottom+75.255
G00 F600.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.767 Y72.715; move !!Xleft+70.767 Ybottom+72.715
G00 F600.0 Z0.000; pen down !!Zwork
G01 F600.0 X101.247 Y72.715; draw !!Xleft+101.247 Ybottom+72.715
G00 F600.0 Z20.000; pen park !!Zpark


M0 ;pause - remove pen reset drill offset 
G00 F2400.0 Y12.000; !!Ybottom - drill to correct x
G00 F2400.0 X29.000; !!Xleft - drill to correct y
G92 X0 Y0
M0 ;pause - verify drill is at origin - set depth manually if needed via cmd, then make the max depth equal to 0 with G92 Z0
;Manually Drill a test hole with G92 Z#.### to verify correct X,Y,Z zeros and location.
;Do Holes -this part of file moves slow and has a greater Z height between moves so as to assure bit is out of work area


G00 F2400.0 X100.990 Y69.933; move !!Xleft+100.990 Ybottom+69.933
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X101.490 Y70.433; draw !!Xleft+101.490 Ybottom+70.433
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X100.990 Y72.473; move !!Xleft+100.990 Ybottom+72.473
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X101.490 Y72.973; draw !!Xleft+101.490 Ybottom+72.973
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X100.990 Y75.013; move !!Xleft+100.990 Ybottom+75.013
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X101.490 Y75.513; draw !!Xleft+101.490 Ybottom+75.513
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X100.990 Y77.553; move !!Xleft+100.990 Ybottom+77.553
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X101.490 Y78.053; draw !!Xleft+101.490 Ybottom+78.053
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X100.990 Y80.093; move !!Xleft+100.990 Ybottom+80.093
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X101.490 Y80.593; draw !!Xleft+101.490 Ybottom+80.593
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X101.490 Y83.133; move !!Xleft+101.490 Ybottom+83.133
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X100.990 Y82.633; draw !!Xleft+100.990 Ybottom+82.633
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X87.470 Y79.273; move !!Xleft+87.470 Ybottom+79.273
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X87.070 Y78.873; draw !!Xleft+87.070 Ybottom+78.873
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X81.120 Y79.273; move !!Xleft+81.120 Ybottom+79.273
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X80.720 Y78.873; draw !!Xleft+80.720 Ybottom+78.873
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X76.040 Y79.273; move !!Xleft+76.040 Ybottom+79.273
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X75.640 Y78.873; draw !!Xleft+75.640 Ybottom+78.873
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.960 Y78.003; move !!Xleft+70.960 Ybottom+78.003
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.560 Y77.603; draw !!Xleft+70.560 Ybottom+77.603
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X69.688 Y82.981; move !!Xleft+69.688 Ybottom+82.981
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X69.138 Y82.431; draw !!Xleft+69.138 Ybottom+82.431
G01 F300.0 X69.334 Y83.334; draw !!Xleft+69.334 Ybottom+83.334
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X69.138 Y88.931; move !!Xleft+69.138 Ybottom+88.931
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X69.688 Y89.481; draw !!Xleft+69.688 Ybottom+89.481
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X69.334 Y89.834; move !!Xleft+69.334 Ybottom+89.834
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X68.784 Y89.284; draw !!Xleft+68.784 Ybottom+89.284
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X65.187 Y89.481; move !!Xleft+65.187 Ybottom+89.481
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X64.637 Y88.931; draw !!Xleft+64.637 Ybottom+88.931
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X64.834 Y89.834; move !!Xleft+64.834 Ybottom+89.834
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X64.284 Y89.284; draw !!Xleft+64.284 Ybottom+89.284
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X64.834 Y83.334; move !!Xleft+64.834 Ybottom+83.334
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X64.284 Y82.784; draw !!Xleft+64.284 Ybottom+82.784
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X65.187 Y82.981; move !!Xleft+65.187 Ybottom+82.981
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X64.637 Y82.431; draw !!Xleft+64.637 Ybottom+82.431
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y78.003; move !!Xleft+63.340 Ybottom+78.003
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y77.603; draw !!Xleft+62.940 Ybottom+77.603
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X62.940 Y75.063; move !!Xleft+62.940 Ybottom+75.063
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X63.340 Y75.463; draw !!Xleft+63.340 Ybottom+75.463
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y75.063; move !!Xleft+70.560 Ybottom+75.063
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y75.463; draw !!Xleft+70.960 Ybottom+75.463
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.960 Y72.923; move !!Xleft+70.960 Ybottom+72.923
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.560 Y72.523; draw !!Xleft+70.560 Ybottom+72.523
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.960 Y70.383; move !!Xleft+70.960 Ybottom+70.383
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.560 Y69.983; draw !!Xleft+70.560 Ybottom+69.983
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X80.695 Y67.418; move !!Xleft+80.695 Ybottom+67.418
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X81.145 Y67.868; draw !!Xleft+81.145 Ybottom+67.868
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X83.235 Y67.418; move !!Xleft+83.235 Ybottom+67.418
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X83.685 Y67.868; draw !!Xleft+83.685 Ybottom+67.868
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X87.070 Y67.443; move !!Xleft+87.070 Ybottom+67.443
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X87.470 Y67.843; draw !!Xleft+87.470 Ybottom+67.843
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X95.010 Y60.223; move !!Xleft+95.010 Ybottom+60.223
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X94.610 Y59.823; draw !!Xleft+94.610 Ybottom+59.823
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X95.010 Y53.873; move !!Xleft+95.010 Ybottom+53.873
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X94.610 Y53.473; draw !!Xleft+94.610 Ybottom+53.473
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X89.610 Y53.473; move !!Xleft+89.610 Ybottom+53.473
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X90.010 Y53.873; draw !!Xleft+90.010 Ybottom+53.873
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X90.010 Y60.223; move !!Xleft+90.010 Ybottom+60.223
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X89.610 Y59.823; draw !!Xleft+89.610 Ybottom+59.823
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X81.120 Y58.953; move !!Xleft+81.120 Ybottom+58.953
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X80.720 Y58.553; draw !!Xleft+80.720 Ybottom+58.553
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X81.120 Y54.053; move !!Xleft+81.120 Ybottom+54.053
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X80.720 Y53.653; draw !!Xleft+80.720 Ybottom+53.653
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.960 Y52.603; move !!Xleft+70.960 Ybottom+52.603
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.560 Y52.203; draw !!Xleft+70.560 Ybottom+52.203
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y54.743; move !!Xleft+70.560 Ybottom+54.743
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y55.143; draw !!Xleft+70.960 Ybottom+55.143
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y57.283; move !!Xleft+70.560 Ybottom+57.283
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y57.683; draw !!Xleft+70.960 Ybottom+57.683
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y59.823; move !!Xleft+70.560 Ybottom+59.823
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y60.223; draw !!Xleft+70.960 Ybottom+60.223
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y62.363; move !!Xleft+70.560 Ybottom+62.363
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y62.763; draw !!Xleft+70.960 Ybottom+62.763
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y64.903; move !!Xleft+70.560 Ybottom+64.903
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y65.303; draw !!Xleft+70.960 Ybottom+65.303
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y67.443; move !!Xleft+70.560 Ybottom+67.443
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y67.843; draw !!Xleft+70.960 Ybottom+67.843
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y72.923; move !!Xleft+63.340 Ybottom+72.923
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y72.523; draw !!Xleft+62.940 Ybottom+72.523
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y70.383; move !!Xleft+63.340 Ybottom+70.383
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y69.983; draw !!Xleft+62.940 Ybottom+69.983
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y67.843; move !!Xleft+63.340 Ybottom+67.843
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y67.443; draw !!Xleft+62.940 Ybottom+67.443
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y65.303; move !!Xleft+63.340 Ybottom+65.303
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y64.903; draw !!Xleft+62.940 Ybottom+64.903
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y62.763; move !!Xleft+63.340 Ybottom+62.763
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y62.363; draw !!Xleft+62.940 Ybottom+62.363
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y60.223; move !!Xleft+63.340 Ybottom+60.223
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y59.823; draw !!Xleft+62.940 Ybottom+59.823
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y57.683; move !!Xleft+63.340 Ybottom+57.683
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y57.283; draw !!Xleft+62.940 Ybottom+57.283
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y55.143; move !!Xleft+63.340 Ybottom+55.143
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y54.743; draw !!Xleft+62.940 Ybottom+54.743
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X56.990 Y55.143; move !!Xleft+56.990 Ybottom+55.143
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X56.590 Y54.743; draw !!Xleft+56.590 Ybottom+54.743
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.395 Y50.088; move !!Xleft+49.395 Ybottom+50.088
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X48.945 Y49.638; draw !!Xleft+48.945 Ybottom+49.638
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X51.485 Y49.638; move !!Xleft+51.485 Ybottom+49.638
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X51.935 Y50.088; draw !!Xleft+51.935 Ybottom+50.088
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X56.590 Y49.663; move !!Xleft+56.590 Ybottom+49.663
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X56.990 Y50.063; draw !!Xleft+56.990 Ybottom+50.063
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X62.940 Y52.203; move !!Xleft+62.940 Ybottom+52.203
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X63.340 Y52.603; draw !!Xleft+63.340 Ybottom+52.603
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y50.063; move !!Xleft+63.340 Ybottom+50.063
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y49.663; draw !!Xleft+62.940 Ybottom+49.663
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X62.940 Y47.123; move !!Xleft+62.940 Ybottom+47.123
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X63.340 Y47.523; draw !!Xleft+63.340 Ybottom+47.523
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.560 Y49.663; move !!Xleft+70.560 Ybottom+49.663
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.960 Y50.063; draw !!Xleft+70.960 Ybottom+50.063
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.960 Y47.523; move !!Xleft+70.960 Ybottom+47.523
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.560 Y47.123; draw !!Xleft+70.560 Ybottom+47.123
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X70.960 Y44.983; move !!Xleft+70.960 Ybottom+44.983
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X70.560 Y44.583; draw !!Xleft+70.560 Ybottom+44.583
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X63.340 Y44.983; move !!Xleft+63.340 Ybottom+44.983
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X62.940 Y44.583; draw !!Xleft+62.940 Ybottom+44.583
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X49.607 Y35.605; move !!Xleft+49.607 Ybottom+35.605
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X48.958 Y34.957; draw !!Xleft+48.958 Ybottom+34.957
G00 F180.0 Z10.000; pen up !!Zup
G00 F2400.0 X48.591 Y35.297; move !!Xleft+48.591 Ybottom+35.297
G00 F180.0 Z0.000; pen down !!Zwork
G01 F300.0 X49.240 Y35.945; draw !!Xleft+49.240 Ybottom+35.945
G00 F180.0 Z20.000; pen park !!Zpark