Alex Kit Certification - Revision history

Marcin: /* Evaluation */

2018-11-20T16:57:20Z

Evaluation

← Older revision		Revision as of 16:57, 20 November 2018
Line 36:		Line 36:
	#Two bed standoff nuts did not fit on 8 mm rods - used other nuts		#Two bed standoff nuts did not fit on 8 mm rods - used other nuts
	#Wire on the Z probe connector - excessively long, had to wrap up many more times in the final wiring. Works, but took more time.		#Wire on the Z probe connector - excessively long, had to wrap up many more times in the final wiring. Works, but took more time.
	#Control panel - MOSFET too close to USB plug - needs to go a little to the right, and need to correct instructions		#Control panel - MOSFET too close to USB plug - needs to go a little to the right, and need to correct instructions. Also, needs 3rd mounting hole on MOSFET so the MOSFET doesn't slouch forward.
	#Spool holder pieces had to be reamed out (heated then set on rods)		#Spool holder pieces had to be reamed out (heated then set on rods)
	#PEI was already attached. Should be left for the builder.		#PEI was already attached. Should be left for the builder.

Marcin: /* Evaluation */

2018-11-20T16:56:20Z

Evaluation

← Older revision		Revision as of 16:56, 20 November 2018
Line 34:		Line 34:
	#It turns out that 8 mm shafts were tight. I replaced X and Y shafts with 5/16" shafts. This issue may depend on filament and printer - for the printed part quality. I left the Z axes at 8 mm - but needed extra glide on X and Y for speed.		#It turns out that 8 mm shafts were tight. I replaced X and Y shafts with 5/16" shafts. This issue may depend on filament and printer - for the printed part quality. I left the Z axes at 8 mm - but needed extra glide on X and Y for speed.
	#Back bottom Z axis hole was too far down for the Z axis to fit - had to redrill the hole higher.		#Back bottom Z axis hole was too far down for the Z axis to fit - had to redrill the hole higher.
	#		#Two bed standoff nuts did not fit on 8 mm rods - used other nuts
			#Wire on the Z probe connector - excessively long, had to wrap up many more times in the final wiring. Works, but took more time.
			#Control panel - MOSFET too close to USB plug - needs to go a little to the right, and need to correct instructions
			#Spool holder pieces had to be reamed out (heated then set on rods)
			#PEI was already attached. Should be left for the builder.
			#End stop holders need modification, Both holes do not fit - one hole only is glued. Had to scrape mid of endstop to make it fit (missed this in Sara's build evaluation)
			#Wire of power supply needs to point sideways, not down (same issue in Sara's)

	=Links=		=Links=
	*[[Prepping for 1st Kit Building]]		*[[Prepping for 1st Kit Building]]

Marcin: /* Evaluation */

2018-11-20T16:48:33Z

Evaluation

← Older revision		Revision as of 16:48, 20 November 2018
Line 25:		Line 25:
	=Evaluation=		=Evaluation=
	<html><iframe width="560" height="315" src="https://www.youtube.com/embed/EVK28rUZct8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>		<html><iframe width="560" height="315" src="https://www.youtube.com/embed/EVK28rUZct8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

			Kit build went well. There were missing parts (not printed) that were substituted (first picture in video above), and some issues:
			#LCD did not work
			#LCD location on control panel was in the way of the cable chain due to old documentation (main documentation has been since updated)
			#Printed carriages needed cleaning
			#There was an additional hole in the front frame piece which marcin mistook for a Z axis hole, only to find out that it did not have the opposing hole, and this resulted in a build error. I had to redrill a hole for the second Z.
			#Frame had old epoxy on it. Had to clean it with a knife and grinder.
			#It turns out that 8 mm shafts were tight. I replaced X and Y shafts with 5/16" shafts. This issue may depend on filament and printer - for the printed part quality. I left the Z axes at 8 mm - but needed extra glide on X and Y for speed.
			#Back bottom Z axis hole was too far down for the Z axis to fit - had to redrill the hole higher.
			#

	=Links=		=Links=
	*[[Prepping for 1st Kit Building]]		*[[Prepping for 1st Kit Building]]

Marcin: /* Evaluation */

2018-11-20T16:42:29Z

Evaluation

← Older revision		Revision as of 16:42, 20 November 2018
Line 24:		Line 24:

	=Evaluation=		=Evaluation=
	*See Main spreadsheet above.		<html><iframe width="560" height="315" src="https://www.youtube.com/embed/EVK28rUZct8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

	=Links=		=Links=
	*[[Prepping for 1st Kit Building]]		*[[Prepping for 1st Kit Building]]

Marcin at 16:27, 20 November 2018

2018-11-20T16:27:17Z

← Older revision		Revision as of 16:27, 20 November 2018
Line 22:		Line 22:

	[https://docs.google.com/spreadsheets/d/1FhlzOXlx9gDl9IkadzLJBlQ7obsZjdiJURAZUjvUyVM/edit#gid=440076612 edit]		[https://docs.google.com/spreadsheets/d/1FhlzOXlx9gDl9IkadzLJBlQ7obsZjdiJURAZUjvUyVM/edit#gid=440076612 edit]

			=Evaluation=
			*See Main spreadsheet above.

	=Links=		=Links=
	*[[Prepping for 1st Kit Building]]		*[[Prepping for 1st Kit Building]]

Marcin: /* Links */

2018-11-08T23:46:19Z

Links

← Older revision		Revision as of 23:46, 8 November 2018
Line 25:		Line 25:
	=Links=		=Links=
	*[[Prepping for 1st Kit Building]]		*[[Prepping for 1st Kit Building]]
	*[[Alex Parts Inventory]]
	*Heat break size?

Marcin at 17:40, 7 November 2018

2018-11-07T17:40:06Z

← Older revision		Revision as of 17:40, 7 November 2018
Line 1:		Line 1:
			=Build Space=

			Make a copy of:

			<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vSdnEaF2sf2ORPESJhIb1Bhquov-ZOh5sjbFAgT_BcNSyee0Q12eUFTsMdb6r4HEsrO17KvC3gozMSN/embed?start=false&loop=false&delayms=3000" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>

			[https://docs.google.com/presentation/d/1KGWenTMrttuJIoEpXvef1ICN8QQa0vD1EA0LrJm4tQA/edit#slide=id.g4071900322_0_32 edit]


	=Main Certification Spreadsheet=		=Main Certification Spreadsheet=
	make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0		make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0

Marcin: /* Spreadsheet */

2018-11-07T17:36:27Z

Spreadsheet

← Older revision		Revision as of 17:36, 7 November 2018
Line 1:		Line 1:
	=Spreadsheet=		=Main Certification Spreadsheet=
	make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0		make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0

Marcin: /* Spreadsheet */

2018-11-07T17:36:15Z

Spreadsheet

← Older revision		Revision as of 17:36, 7 November 2018
Line 1:		Line 1:
	=Spreadsheet=		=Spreadsheet=
			make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0
	~~<html><iframe src="https://docs.google.com/spreadsheets/d/e/2PACX~~-~~1vSXCg_lsC3w_3uVxDAaXUlKMogto8d9n59vbe80Rckjm9BH16c8wlUqgYB4_yT4G0F1gWz7DjDFfzIu/pubhtml?widget=true&headers=false" height=500 width=1000></iframe></html>~~

	https://docs.google.com/spreadsheets/d/~~1JhQnZPx6u0c22sgaoCL22G8c0626dGyagXsDBnxev2Q~~/edit#gid=0


	=Electronics Certification=		=Electronics Certification=

Marcin: /* Kit Inventory */

2018-11-07T17:35:47Z

Kit Inventory

← Older revision		Revision as of 17:35, 7 November 2018
Line 5:		Line 5:
	https://docs.google.com/spreadsheets/d/1JhQnZPx6u0c22sgaoCL22G8c0626dGyagXsDBnxev2Q/edit#gid=0		https://docs.google.com/spreadsheets/d/1JhQnZPx6u0c22sgaoCL22G8c0626dGyagXsDBnxev2Q/edit#gid=0


			=Electronics Certification=

			make copy of https://docs.google.com/presentation/d/1tuqGoRbD_J-1NZOyky5YsDny67ybINcYIUi9IxU4gtc/edit#slide=id.g4071900322_0_32

	=Kit Inventory=		=Kit Inventory=
Line 13:		Line 17:

	[https://docs.google.com/spreadsheets/d/1FhlzOXlx9gDl9IkadzLJBlQ7obsZjdiJURAZUjvUyVM/edit#gid=440076612 edit]		[https://docs.google.com/spreadsheets/d/1FhlzOXlx9gDl9IkadzLJBlQ7obsZjdiJURAZUjvUyVM/edit#gid=440076612 edit]


	=Links=		=Links=