Assemble Power Cube - Revision history

KhalidH at 22:49, 27 December 2013

2013-12-27T22:49:27Z

← Older revision		Revision as of 22:49, 27 December 2013
Line 33:		Line 33:

	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]
			[[category:Power Cube]]

2011-06-19T01:05:52Z

@@ Line 19: / Line 19: @@
 **Verify that height of engine makes pump stick out 1" above bottom plane of the Power Cube
 **Tack weld hydraulic pump plate, and connecting vertical plate
 [[Category:Fabrication Procedures]]

2011-06-19T01:01:30Z

← Older revision		Revision as of 01:01, 19 June 2011
Line 18:		Line 18:
	**Attach lovejoy coupler to engine		**Attach lovejoy coupler to engine
	**Verify that height of engine makes pump stick out 1" above bottom plane of the Power Cube		**Verify that height of engine makes pump stick out 1" above bottom plane of the Power Cube
			**Tack weld hydraulic pump plate, and connecting vertical plate

	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]

2011-06-19T01:00:36Z

← Older revision		Revision as of 01:00, 19 June 2011
Line 17:		Line 17:
	**Place engine in position		**Place engine in position
	**Attach lovejoy coupler to engine		**Attach lovejoy coupler to engine
	**~~Adjust~~ height of ~~angle to allow hydraulic~~ pump to stick 1" above bottom plane of the Power Cube		**Verify that height of engine makes pump stick out 1" above bottom plane of the Power Cube

	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]

2011-06-19T00:59:43Z

← Older revision		Revision as of 00:59, 19 June 2011
Line 11:		Line 11:
	**Torch engine mount plate pattern- best is plasma cutter		**Torch engine mount plate pattern- best is plasma cutter
	**Torch hydraulic pump mount plate pattern		**Torch hydraulic pump mount plate pattern
	**Tack weld angle to frame ~~and~~ mount ~~plates~~ to hydraulic tank		**Measure distance from bottom of pump to bottom plane of engine
			**Use this measurement to determine height of engine mount plate in frame
			**Tack weld angle to frame
			**Tack weld engine mount plate to hydraulic tank and angle
	**Place engine in position		**Place engine in position
	**Attach lovejoy coupler to engine		**Attach lovejoy coupler to engine

2011-06-19T00:57:29Z

← Older revision		Revision as of 00:57, 19 June 2011
Line 11:		Line 11:
	**Torch engine mount plate pattern- best is plasma cutter		**Torch engine mount plate pattern- best is plasma cutter
	**Torch hydraulic pump mount plate pattern		**Torch hydraulic pump mount plate pattern
	**Adjust height of angle to allow hydraulic pump to stick 1" above bottom plane of the Power Cube
	**Tack weld angle to frame and mount plates to hydraulic tank		**Tack weld angle to frame and mount plates to hydraulic tank
	**Place engine in position		**Place engine in position
	**Attach lovejoy coupler to engine		**Attach lovejoy coupler to engine
			**Adjust height of angle to allow hydraulic pump to stick 1" above bottom plane of the Power Cube

	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]

2011-06-19T00:55:52Z

← Older revision		Revision as of 00:55, 19 June 2011
Line 2:		Line 2:
	*Weld hydraulic tank onto frame, with suction strainer assembly in place. Orientation faces the operator when looking backwards at the Power Cube.		*Weld hydraulic tank onto frame, with suction strainer assembly in place. Orientation faces the operator when looking backwards at the Power Cube.
	*Weld fuel tank to frame. Orientation is away from operator (safety) on the rear left corner of frame.		*Weld fuel tank to frame. Orientation is away from operator (safety) on the rear left corner of frame.
	*[[Mount Engine and Pump]]:		*Mount Engine and Pump:
	**Trim engine shaft to 2"		**Trim engine shaft to 2"
	**Put hydraulic fittings on hydraulic pump, and connect lovejoy coupler to pump		**Put hydraulic fittings on hydraulic pump, and connect lovejoy coupler to pump

2011-06-19T00:55:38Z

← Older revision		Revision as of 00:55, 19 June 2011
Line 9:		Line 9:
	**[1] Cut 1/4"x8"x3"? connecting plate		**[1] Cut 1/4"x8"x3"? connecting plate
	**[1] Cut 1/4"x2" angle for Power Cube Mount		**[1] Cut 1/4"x2" angle for Power Cube Mount
	**Torch engine mount plate - best is plasma cutter		**Torch engine mount plate pattern- best is plasma cutter
	**Torch hydraulic pump plate		**Torch hydraulic pump mount plate pattern
	**Adjust height of angle to allow hydraulic pump to stick 1" above bottom plane of the Power Cube		**Adjust height of angle to allow hydraulic pump to stick 1" above bottom plane of the Power Cube
	**Tack weld angle to frame and mount plates to hydraulic tank		**Tack weld angle to frame and mount plates to hydraulic tank

2011-06-19T00:45:17Z

← Older revision		Revision as of 00:45, 19 June 2011
Line 4:		Line 4:
	*[[Mount Engine and Pump]]:		*[[Mount Engine and Pump]]:
	**Trim engine shaft to 2"		**Trim engine shaft to 2"
	*Put fittings on hydraulic pump		**Put hydraulic fittings on hydraulic pump, and connect lovejoy coupler to pump
	**[1] Cut plate for Engine Mount - 1/4"x8"x20"?		**[1] Cut plate for Engine Mount - 1/4"x8"x20"?
	**[1] Cut plate for hydraulic pump - 1/4"x8"x?		**[1] Cut plate for hydraulic pump - 1/4"x8"x?

2011-06-19T00:44:26Z

@@ Line 2: / Line 2: @@
 *Weld hydraulic tank onto frame, with suction strainer assembly in place. Orientation faces the operator when looking backwards at the Power Cube.
 *Weld fuel tank to frame. Orientation is away from operator (safety) on the rear left corner of frame.
-*[[Mount Engine and Pump]]
+*[[Mount Engine and Pump]]:
 [[Category:Fabrication Procedures]]