Backhoe Conceptual Specifications - Revision history

Marcin at 06:01, 16 May 2013

2013-05-16T06:01:36Z

← Older revision		Revision as of 06:01, 16 May 2013
Line 1:		Line 1:
			*Bonding plates have 1" holes, and all holes are 1". Pivot holes are 3" for heavy duty pivots.
	*Based on 4x4 inch tubing, 1/4" or 1/2" wall depending on strength required		*Based on 4x4 inch tubing, 1/4" or 1/2" wall depending on strength required
	*Scaling can happen by:		*Scaling can happen by:
Line 12:		Line 13:

	=Design for Prototyping=		=Design for Prototyping=
	*Using 4x4 beams, sections of any length can be made to allow fit of any cylinder. Mounting plates allow for cylinders to be fitted in any location, as 1" holes of mounting plates can be used as holes for pin of cylinder. Thus, boom and stick of the backhoe can be made to size as needed. ~~Cylinders mound on~~		*Using 4x4 beams, sections of any length can be made to allow fit of any cylinder. Mounting plates allow for cylinders to be fitted in any location, as 1" holes of mounting plates can be used as holes for pin of cylinder. Thus, boom and stick of the backhoe can be made to size as needed. Plates can be layered as much as needed.


	=Ecology=		=Ecology=

Marcin at 06:00, 16 May 2013

2013-05-16T06:00:05Z

← Older revision		Revision as of 06:00, 16 May 2013
Line 10:		Line 10:
	**Stacking of pivot joints plates to increase pivot strength		**Stacking of pivot joints plates to increase pivot strength
	*Pivot joints are used to couple tubing members		*Pivot joints are used to couple tubing members

			=Design for Prototyping=
			*Using 4x4 beams, sections of any length can be made to allow fit of any cylinder. Mounting plates allow for cylinders to be fitted in any location, as 1" holes of mounting plates can be used as holes for pin of cylinder. Thus, boom and stick of the backhoe can be made to size as needed. Cylinders mound on


	=Ecology=		=Ecology=

Marcin: /* Ecology */

2013-05-16T01:19:21Z

Ecology

← Older revision		Revision as of 01:19, 16 May 2013
Line 14:		Line 14:
	*Same technique for creating articulated joints may be applied to creating loader arms or cherrypicker arms		*Same technique for creating articulated joints may be applied to creating loader arms or cherrypicker arms
	*Similar technique may be used to build well drilling rig frames		*Similar technique may be used to build well drilling rig frames
			*Similar technique is used to build the ironworker machine.

Marcin at 01:18, 16 May 2013

2013-05-16T01:18:48Z

← Older revision		Revision as of 01:18, 16 May 2013
Line 1:		Line 1:
	*Based on 4x4 inch tubing, 1/4" or 1/2" wall depending on ~~side~~		*Based on 4x4 inch tubing, 1/4" or 1/2" wall depending on strength required
	*Scaling can happen by:		*Scaling can happen by:
	**Extension of tube members		**Extension of tube members inlength
	**By stacking tube members on top of each other in one direction		**By stacking tube members on top of each other in one direction
	**By stacking tube members on top of each other in two directions		**By stacking tube members on top of each other in two directions
			**By stacking tube members in a space frame configuration by using connector plates.
			**Using thicker wall of tubing
			**May be connected to one another by plates
			**Stacking of connector plates for increasing strength
			**Stacking of pivot joints plates to increase pivot strength
			*Pivot joints are used to couple tubing members

			=Ecology=
			*Same technique for creating articulated joints may be applied to creating loader arms or cherrypicker arms
			*Similar technique may be used to build well drilling rig frames

Marcin: Created page with "Based on 4x4 inch tubing, 1/4" or 1/2" wall depending on side Scaling can happen by: Extension of tube members By stacking tube members on top of each other in one direc..."

2013-05-16T01:13:55Z

Created page with "*Based on 4x4 inch tubing, 1/4" or 1/2" wall depending on side *Scaling can happen by: **Extension of tube members **By stacking tube members on top of each other in one direc..."

New page