Build Wheel Shafts - Revision history

Marcin at 05:23, 19 June 2011

2011-06-19T05:23:54Z

← Older revision		Revision as of 05:23, 19 June 2011
Line 13:		Line 13:
	*Torch out 3" long slit in 1-7/8" shaft, on two sides of shaft		*Torch out 3" long slit in 1-7/8" shaft, on two sides of shaft
	*Plug weld spline shafting in hole, on lathe if necessary for alignment		*Plug weld spline shafting in hole, on lathe if necessary for alignment
	*		*Trim the 6-spline shafting so that there is no gap between the shafting and the female coupler on motor.


	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]

Marcin at 05:22, 19 June 2011

2011-06-19T05:22:33Z

← Older revision		Revision as of 05:22, 19 June 2011
Line 9:		Line 9:

	'''Motor End'''		'''Motor End'''
			*Use 6" stub of standard 1-3/8" 6 spline shafting
	*End drill 3.5" deep (on a lathe) the 1-3/8" receiver for 6-spline standard PTO shafting		*End drill 3.5" deep (on a lathe) the 1-3/8" receiver for 6-spline standard PTO shafting
			*Torch out 3" long slit in 1-7/8" shaft, on two sides of shaft
			*Plug weld spline shafting in hole, on lathe if necessary for alignment
			*


	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]

Marcin at 05:19, 19 June 2011

2011-06-19T05:19:04Z

← Older revision		Revision as of 05:19, 19 June 2011
Line 1:		Line 1:
			'''Wheel End'''

	*Cut 1-7/8" shafts to 28"		*Cut 1-7/8" shafts to 28"
	*Cut 6" long collars from 2" pipe		*Cut 6" long collars from 2" pipe
Line 5:		Line 7:
	**Drill through collar and shaft at the same time		**Drill through collar and shaft at the same time
	*Weld on reinforcing nuts on collars		*Weld on reinforcing nuts on collars

			'''Motor End'''
	*End drill 3.5" deep (on a lathe) the 1-3/8" receiver for 6-spline standard PTO shafting		*End drill 3.5" deep (on a lathe) the 1-3/8" receiver for 6-spline standard PTO shafting

	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]

Marcin: Created page with "Cut 1-7/8" shafts to 28" Cut 6" long collars from 2" pipe Label collar and shaft, as these are paired up and can't be confused between shafts. Drill 3/4" hole for wheel plate..."

2011-06-19T01:45:50Z

Created page with "*Cut 1-7/8" shafts to 28" *Cut 6" long collars from 2" pipe *Label collar and shaft, as these are paired up and can't be confused between shafts. *Drill 3/4" hole for wheel plate..."

New page

*Cut 1-7/8" shafts to 28"
*Cut 6" long collars from 2" pipe
*Label collar and shaft, as these are paired up and can't be confused between shafts.
*Drill 3/4" hole for wheel plate mounting through shaft and collar
**Drill through collar and shaft at the same time
*Weld on reinforcing nuts on collars
*End drill 3.5" deep (on a lathe) the 1-3/8" receiver for 6-spline standard PTO shafting

[[Category:Fabrication Procedures]]

Build Wheel Shafts - Revision history

Marcin at 05:23, 19 June 2011

Marcin at 05:22, 19 June 2011

Marcin at 05:19, 19 June 2011

Marcin: Created page with "*Cut 1-7/8" shafts to 28" *Cut 6" long collars from 2" pipe *Label collar and shaft, as these are paired up and can't be confused between shafts. *Drill 3/4" hole for wheel plate..."

Marcin: Created page with "Cut 1-7/8" shafts to 28" Cut 6" long collars from 2" pipe Label collar and shaft, as these are paired up and can't be confused between shafts. Drill 3/4" hole for wheel plate..."