CEB Press/Manufacturing Instructions/Arms - secondary - Revision history

YK at 00:59, 23 December 2011

2011-12-23T00:59:50Z

← Older revision		Revision as of 00:59, 23 December 2011
Line 1:		Line 1:
	{{Category=CEB press building instructions}}		{{Category=CEB press building instructions}}
	~~{{Template:CEB Press Manufacturing Instructions Navbox}}~~

	[[Image:Secondaryarms.jpg\|400px]]		[[Image:Secondaryarms.jpg\|400px]]
	~~The secondary arms connect the primary arm/frame assembly to the legs to support the structure.~~

	== Tools Required ==		<html>
			<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>
			</html><br/>

			[[Image:2ndarmweldover.png\|800px]]

			=Part Information=

			The secondary arms connect the primary arms to the legs to support the structure.

			=Tools Required=

	*Cutting Torch		*Cutting Torch

	*Angle Grinder		*Angle Grinder

	*Welder		*Welder

	== Materials Required ==		=Materials Required=

	*2 ~~pieces 72" long -~~ 4"x6"x1/2" ~~angle steel~~		*[2] Steel Angle 4" A x 6" B x 1/2" Thickness x 72" Length
	*1 piece 3"x3"~~x1/2" steel~~
	*[[CEB Press/Manufacturing Instructions/Leg Holders\|Leg Holders]](8)

	~~== Diagrams ==~~		*Steel Plate 3" x 3" x 1/2"
	~~<html>~~
	~~<iframe src=~~"~~http://sketchup.google.com/3dwarehouse~~/~~mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no~~" ~~marginheight="0" marginwidth="0" width="400" height="300"></iframe>~~		*[8] Leg Holders
	~~</html><br/>~~
	[~~[Image:2ndarmweldover.png\|800px]~~]

	== Fabrication Steps ==		== Fabrication Steps ==
	#Punch the holes in each arm. They are symmetrical.
	#Place the leg holders in their proper locations.		*Punch the holes in each arm. They are symmetrical.
	#*They go on the 4" side of the angle.
	#*They are symmetric. See Diagram for placement on each end.		*Place the leg holders in their proper locations.
	#*Make sure they are square with the angle iron and centered vertically.
	#Weld them to the angle.		*They go on the 4" side of the angle.

			*They are symmetric. See Diagram for placement on each end.

			*Make sure they are square with the angle iron and centered vertically.

			*Weld them to the angle.

Bkufa: /* Fabrication Steps */

2011-12-14T18:20:48Z

Fabrication Steps

← Older revision		Revision as of 18:20, 14 December 2011
Line 24:		Line 24:

	== Fabrication Steps ==		== Fabrication Steps ==
	#Punch the holes in each arm. They are symmetrical		#Punch the holes in each arm. They are symmetrical.
	#Place the leg holders in their proper locations.		#Place the leg holders in their proper locations.
	#*They go on the 4" side of the angle.		#*They go on the 4" side of the angle.
	#*They are symmetric. See Diagram for placement on each end.		#*They are symmetric. See Diagram for placement on each end.
	#Make sure they are square with the angle iron and centered vertically.		#*Make sure they are square with the angle iron and centered vertically.
	#*Weld them to the ~~machine~~.		#Weld them to the angle.
	~~#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)~~

Bkufa at 17:44, 14 December 2011

2011-12-14T17:44:05Z

← Older revision		Revision as of 17:44, 14 December 2011
Line 24:		Line 24:

	== Fabrication Steps ==		== Fabrication Steps ==
	~~You will be torching~~ the holes ~~and welding the tab for the secondary cylinder during the final assembly of the machine~~.		#Punch the holes in each arm. They are symmetrical
	~~For now:~~
	#Place the leg holders in their proper locations.		#Place the leg holders in their proper locations.
	#*They go on the 4" side of the angle.		#*They go on the 4" side of the angle.
Line 32:		Line 31:
	#*Weld them to the machine.		#*Weld them to the machine.
	#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)		#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)
	~~#Put bolts in the outside leg holders on each arm.~~

Bkufa: /* Fabrication Steps */

2011-12-14T00:30:19Z

Fabrication Steps

← Older revision		Revision as of 00:30, 14 December 2011
Line 28:		Line 28:
	#Place the leg holders in their proper locations.		#Place the leg holders in their proper locations.
	#*They go on the 4" side of the angle.		#*They go on the 4" side of the angle.
	#*They are ~~symetric~~. See Diagram for placement on each end.		#*They are symmetric. See Diagram for placement on each end.
	#Make sure they are square with the angle iron and centered vertically.		#Make sure they are square with the angle iron and centered vertically.
	#*Weld them to the machine.		#*Weld them to the machine.
	#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)		#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)
	#Put bolts in the outside leg holders on each arm.		#Put bolts in the outside leg holders on each arm.

Bkufa: /* Fabrication Steps */

2011-12-14T00:30:01Z

Fabrication Steps

← Older revision		Revision as of 00:30, 14 December 2011
Line 25:		Line 25:
	== Fabrication Steps ==		== Fabrication Steps ==
	You will be torching the holes and welding the tab for the secondary cylinder during the final assembly of the machine.		You will be torching the holes and welding the tab for the secondary cylinder during the final assembly of the machine.
			For now:
	~~See [[Leg Holders]]~~		#Place the leg holders in their proper locations.
			#*They go on the 4" side of the angle.
	#~~Plase~~ the leg holders in their proper locations ~~(two at each end, and two 12~~" ~~away from~~ the end~~) and weld them in place, insuring~~ they are square with the angle iron.		#*They are symetric. See Diagram for placement on each end.
			#Make sure they are square with the angle iron and centered vertically.
			#*Weld them to the machine.
	#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)		#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)
	#Put bolts in the outside leg holders on each arm.		#Put bolts in the outside leg holders on each arm.

Bkufa: /* Diagrams */

2011-12-14T00:14:01Z

Diagrams

← Older revision		Revision as of 00:14, 14 December 2011
Line 20:		Line 20:
	<html>		<html>
	<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>		<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>
	</html>		</html><br/>
	[[Image:2ndarmweldover.png\|~~400px~~]]		[[Image:2ndarmweldover.png\|800px]]

	== Fabrication Steps ==		== Fabrication Steps ==

Bkufa: /* Diagrams */

2011-12-14T00:13:14Z

Diagrams

← Older revision		Revision as of 00:13, 14 December 2011
Line 21:		Line 21:
	<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>		<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>
	</html>		</html>
			[[Image:2ndarmweldover.png\|400px]]

	== Fabrication Steps ==		== Fabrication Steps ==

Bkufa: /* Diagrams */

2011-12-13T22:33:13Z

Diagrams

← Older revision		Revision as of 22:33, 13 December 2011
Line 18:		Line 18:

	== Diagrams ==		== Diagrams ==

	~~Front Arm~~

	<html>		<html>
	<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=~~ecda29b3822e184ab38804396e417a9b~~&etyp=~~im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>~~		<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=4c317c20fdb7bac61211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>
	~~</html>~~

	~~Back Arm~~

	~~<html>~~
	~~<iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=bf682d89b179f975b38804396e417a9b&etyp=im~~&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe>
	</html>		</html>

Bkufa: /* Fabrication Steps */

2011-10-27T18:32:15Z

Fabrication Steps

← Older revision		Revision as of 18:32, 27 October 2011
Line 39:		Line 39:
	#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)		#*You may want to weld them so the nut is facing sideways instead of straight out, this way the bolts don't stick out any more from the machine. (They like to catch your clothing as you walk by)
	#Put bolts in the outside leg holders on each arm.		#Put bolts in the outside leg holders on each arm.

	~~This is saved for later, during the assembly of the machine:~~
	~~#Clamp one angle iron arm to each side of the primary arms, the 6" side to the underside of the primary arms, with the 4" side facing outwards from the assembly.~~
	~~#Torch thru the holes on the primary arms to make two 3/4" holes on each secondary arm.~~
	~~#Clean up the torch slag with an angle grinder.~~

Dorkmo: corrected, one hole each side now

2011-10-05T01:33:28Z

corrected, one hole each side now

← Older revision		Revision as of 01:33, 5 October 2011
Line 18:		Line 18:

	== Diagrams ==		== Diagrams ==
	~~Note: In the final model, there is only one hole where the secondary arms connect to the primary arms. Please change.~~

	Front Arm		Front Arm