CEB Press/Manufacturing Instructions/Case - Revision history

Zdwiel at 14:39, 23 May 2013

2013-05-23T14:39:52Z

← Older revision		Revision as of 14:39, 23 May 2013
Line 57:		Line 57:
	[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad. You'll need to perform this solution method if initial serial communication tests prove buggy. You cannot perform this after mounting the microcontroller inside the case.		[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad. You'll need to perform this solution method if initial serial communication tests prove buggy. You cannot perform this after mounting the microcontroller inside the case.

	*[[Linked Extension Cord]]		*[[CEB_Press/Manufacturing_Instructions/Linked_Extension_Cord\|Linked Extension Cord Manufacturing Instructions]]

	=Steps=		=Steps=

2013-05-23T14:37:45Z

Materials

← Older revision		Revision as of 14:37, 23 May 2013
Line 57:		Line 57:
	[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad. You'll need to perform this solution method if initial serial communication tests prove buggy. You cannot perform this after mounting the microcontroller inside the case.		[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad. You'll need to perform this solution method if initial serial communication tests prove buggy. You cannot perform this after mounting the microcontroller inside the case.

	*Linked Extension Cord		*[[Linked Extension Cord]]

	~~[http://opensourceecology.org/wiki/CEB_Press/Manufacturing_Instructions/Linked_Extension_Cord Assembly Instructions~~]

	=Steps=		=Steps=

2013-05-23T14:36:41Z

← Older revision		Revision as of 14:36, 23 May 2013
Line 98:		Line 98:

	*Using the screwdriver with the number 2 philips bit, tighten the screws of the wire clamp at the bottom-left of the lug box.		*Using the screwdriver with the number 2 philips bit, tighten the screws of the wire clamp at the bottom-left of the lug box.

			=See Also=

			*[[Terminal Case\|Different Version (old/new?)]]

2011-12-22T18:08:25Z

Materials

← Older revision		Revision as of 18:08, 22 December 2011
Line 55:		Line 55:
	*Arduino Uno Microcontroller		*Arduino Uno Microcontroller

	[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad.		[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad. You'll need to perform this solution method if initial serial communication tests prove buggy. You cannot perform this after mounting the microcontroller inside the case.

	*Linked Extension Cord		*Linked Extension Cord

2011-12-19T03:57:40Z

← Older revision		Revision as of 03:57, 19 December 2011
Line 54:		Line 54:

	*Arduino Uno Microcontroller		*Arduino Uno Microcontroller

			[http://arduino.cc/forum/index.php/topic,52447.0.html Arduino Uno Serial Issue Solution, Replies 2 and 4] Note: for Arduino Uno Version R2, the contact point for entering DFU mode is the top-left male pin instead of the top-left pad.

	*Linked Extension Cord		*Linked Extension Cord

2011-12-13T16:58:45Z

← Older revision		Revision as of 16:58, 13 December 2011
Line 1:		Line 1:
			=Video=

			<html>
			<iframe src="https://player.vimeo.com/video/33580858?title=0&byline=0&portrait=0" width="400" height="225" frameborder="0" webkitAllowFullScreen allowFullScreen></iframe>
			</html>

	=Tools=		=Tools=

2011-12-13T06:00:44Z

2011-12-08T17:59:54Z

Steps

← Older revision		Revision as of 17:59, 8 December 2011
Line 90:		Line 90:

	*Insert the exposed ends of the 5 pieces of 100cm black wire into the lug box through the bottom-middle hole.		*Insert the exposed ends of the 5 pieces of 100cm black wire into the lug box through the bottom-middle hole.

	~~=Steps=~~

	*'''Set up the lug box'''

	~~[[Image:Cutlerhammerbox.jpg\|300px]]~~

2011-12-08T17:57:22Z

Steps

← Older revision		Revision as of 17:57, 8 December 2011
Line 96:		Line 96:

	[[Image:Cutlerhammerbox.jpg\|300px]]		[[Image:Cutlerhammerbox.jpg\|300px]]

	*'''Using a metal cutoff saw, cut in half the terminal strip that is inside the outdoor main lug box in order to create a positive and a negative set of terminal blocks with 3 terminals each.

	~~[[Image:Terminalstrip.jpg\|300px]]~~

	*'''Mount the home wiring box to the inside of the outdoor main lug box by'''

2011-12-06T17:51:55Z

Materials

@@ Line 1: / Line 1: @@
 =Materials=
-*'''Outdoor Main Lug Box'''
+*Outdoor Main Lug Box
-*'''Home Wiring Box'''
+*Using the screwdriver with the flathead bit, screw the exposed end of the 30cm black wire to the lower terminal strip. Connect the other end of the 30cm black wire to the ground pin of the power switch.
-*'''Power Switch'''
+*Using the screwdriver with the flathead bit, screw the 15cm red wire to the upper terminal strip and the 15cm black wire to the lower terminal strip.
-*'''18 AWG Red Wire'''
+*Insert the exposed end of the 100cm red wire into the lug box through the bottom-middle hole.
-*'''18 AWG Black Wire'''
+*Using the screwdriver with the flathead bit, screw the exposed end of the 100cm red wire to the upper terminal strip.
-*'''[10] 16 AWG Spade Terminals'''
+*Insert the exposed ends of the 5 pieces of 100cm black wire into the lug box through the bottom-middle hole.
 =Steps=