CEB Press/Manufacturing Instructions/Controller Mount - Revision history

YK: /* Tools */

2011-12-23T00:29:55Z

Tools

← Older revision		Revision as of 00:29, 23 December 2011
Line 12:		Line 12:

	*Metal Marking Utensil		*Metal Marking Utensil

			*Measuring Tape

	=Materials=		=Materials=

YK: /* Tools */

2011-12-22T23:35:31Z

Tools

← Older revision		Revision as of 23:35, 22 December 2011
Line 9:		Line 9:
	*Hole punch with 13/16" die.		*Hole punch with 13/16" die.

	*Drill press with 1/4" bit.		*Drill press with 5/16" bit.

	*Metal Marking Utensil		*Metal Marking Utensil

YK: /* Steps */

2011-12-22T23:35:19Z

Steps

← Older revision		Revision as of 23:35, 22 December 2011
Line 27:		Line 27:
	*Using the marking utensil and the center punch, mark then center punch the 3 aligned hole locations on the steel plate		*Using the marking utensil and the center punch, mark then center punch the 3 aligned hole locations on the steel plate

	*Drill 1/4" holes through the steel plate at the marked points.		*Drill 5/16" holes through the steel plate at the marked points.

	*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.		*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.

	[[Image:ControllerBoxMount.png]]		[[Image:ControllerBoxMount.png]]

YK: /* Steps */

2011-12-22T22:14:09Z

Steps

← Older revision		Revision as of 22:14, 22 December 2011
Line 31:		Line 31:
	*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.		*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.

	[[Image:ControllerBoxMount.png~~\|700px~~]]		[[Image:ControllerBoxMount.png]]

YK: /* Steps */

2011-12-22T22:13:37Z

Steps

← Older revision		Revision as of 22:13, 22 December 2011
Line 30:		Line 30:

	*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.		*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.

			[[Image:ControllerBoxMount.png\|700px]]

YK: /* Steps */

2011-12-22T22:00:13Z

Steps

← Older revision		Revision as of 22:00, 22 December 2011
Line 29:		Line 29:
	*Drill 1/4" holes through the steel plate at the marked points.		*Drill 1/4" holes through the steel plate at the marked points.

	*Punch 2 holes of 13/16" diameter near the bottom exposed region ~~of the steel plate. The center of these 2 holes should be 10cm apart from each other and 3cm from the bottom edge~~ of the steel plate.		*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate.

YK: /* Steps */

2011-12-22T21:54:06Z

Steps

← Older revision		Revision as of 21:54, 22 December 2011
Line 29:		Line 29:
	*Drill 1/4" holes through the steel plate at the marked points.		*Drill 1/4" holes through the steel plate at the marked points.

	*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate. ~~Specifically, the points are 1 inch~~ from the ~~sides and~~ bottom ~~near~~ the ~~two bottom corners~~.		*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate. The center of these 2 holes should be 10cm apart from each other and 3cm from the bottom edge of the steel plate.

YK at 21:49, 22 December 2011

2011-12-22T21:49:11Z

@@ Line 1: / Line 1: @@
 {{Category=CEB press building instructions}}
-{{Template:CEB Press Manufacturing Instructions Navbox}}
-[[Image:controllermount.jpg|thumb|400px|right|The controller mount view from the back]]
+=Part Information=
 The controller mount attaches the controller box to the primary arms.
-<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=7e774e41eb714c5f1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>
+*The controller mount attaches the controller box to the primary arms.
-=Tools Required=
 *Hole punch with 13/16" die.
-=Diagrams=
+*Drill press with 1/4" bit.
-[[Image:controllerplate2d.jpg|600px]]
-[[Image:controllerplate.png|600px]]
+*Metal Marking Utensil
-=Fabrication instructions=
+*Punch 2 holes of 13/16" diameter near the bottom exposed region of the steel plate. Specifically, the points are 1 inch from the sides and bottom near the two bottom corners.

Bkufa at 02:00, 15 December 2011

2011-12-15T02:00:24Z

← Older revision		Revision as of 02:00, 15 December 2011
Line 3:		Line 3:
	[[Image:controllermount.jpg\|thumb\|400px\|right\|The controller mount view from the back]]		[[Image:controllermount.jpg\|thumb\|400px\|right\|The controller mount view from the back]]
	The controller mount attaches the controller box to the primary arms.		The controller mount attaches the controller box to the primary arms.
	<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=~~2616e5b5a549f3341211da1f85706ccd~~&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>		<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=7e774e41eb714c5f1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>
	=Tools Required=		=Tools Required=
	*Hole punch with 13/16" die.		*Hole punch with 13/16" die.

Bkufa: /* Fabrication instructions */

2011-12-15T01:58:54Z

Fabrication instructions

← Older revision		Revision as of 01:58, 15 December 2011
Line 20:		Line 20:
	#Find your controller box and locate its mounting holes on the back. Use spray paint to spray a nice wet coating over the hole locations, then press your 6x15 plate to it, square and so that the top hole is about a 1/2" away from the top, to mark the hole locations. Center punch them.		#Find your controller box and locate its mounting holes on the back. Use spray paint to spray a nice wet coating over the hole locations, then press your 6x15 plate to it, square and so that the top hole is about a 1/2" away from the top, to mark the hole locations. Center punch them.
	#Drill the 1/4" holes for the controller box. You can drill them a little bigger (up to 5/16") if you'd like, as it's difficult to get the holes perfectly aligned.		#Drill the 1/4" holes for the controller box. You can drill them a little bigger (up to 5/16") if you'd like, as it's difficult to get the holes perfectly aligned.
	#Punch ~~13/16"~~ holes as shown at the bottom of the plate.		#Punch holes as shown at the bottom piece.
			#Weld the bottom piece to the large plate.
	#Weld the 2" flatbar perpendicularly to the plate on the back. The bottom should be flush with it, so the top hole for the controller is still accessible. You only need to weld it in a few spots. (see photo)		#Weld the 2" flatbar perpendicularly to the plate on the back. The bottom should be flush with it, so the top hole for the controller is still accessible. You only need to weld it in a few spots. (see photo)