CEB Press/Manufacturing Instructions/Valve Mount - Revision history

YK: /* Tools */

2011-12-23T00:30:37Z

Tools

← Older revision		Revision as of 00:30, 23 December 2011
Line 10:		Line 10:

	*Drill Press with 5/16" or larger bit.		*Drill Press with 5/16" or larger bit.

			*Center Punch

			*Measuring Tape

			*Metal Marking Utensil

	=Materials=		=Materials=

YK at 00:26, 23 December 2011

2011-12-23T00:26:40Z

← Older revision		Revision as of 00:26, 23 December 2011
Line 15:		Line 15:
	*Steel plate 1/4" x 6" x 12"		*Steel plate 1/4" x 6" x 12"

	*Solenoid Valve ~~Set~~		*Solenoid Valve Subplate with Mount Angles

	=Steps=		=Steps=
Line 21:		Line 21:
	*Set the steel plate on a flat surface		*Set the steel plate on a flat surface

	*Position the solenoid valve ~~set~~ over the plate such that its work port surface is flush with the top edge and square with the side edges of the steel plate.		*Position the solenoid valve subplate with mount angles over the plate such that its work port surface is flush with the top edge and square with the side edges of the steel plate.

	*Using the marking utensil and the center punch, mark then center punch the 4 aligned holes at the sides of the steel plate		*Using the marking utensil and the center punch, mark then center punch the 4 aligned holes at the sides of the steel plate

YK at 00:25, 23 December 2011

2011-12-23T00:25:20Z

← Older revision		Revision as of 00:25, 23 December 2011
Line 1:		Line 1:
	{{Category=CEB press building instructions}}		{{Category=CEB press building instructions}}

	=Part Information		=Part Information=

	The valve mount holds the hydraulic solenoid valves to the primary arm.		*The valve mount holds the hydraulic solenoid valves to the primary arm.

	=Tools=		=Tools=

YK at 00:23, 23 December 2011

2011-12-23T00:23:35Z

← Older revision		Revision as of 00:23, 23 December 2011
Line 1:		Line 1:
	{{Category=CEB press building instructions}}		{{Category=CEB press building instructions}}

			=Part Information

	The valve mount holds the hydraulic solenoid valves to the primary arm.		The valve mount holds the hydraulic solenoid valves to the primary arm.
Line 26:		Line 28:

	*Punch 2 holes of 13/16" diameter that are centered 20cm from each other and 3cm from the bottom edge of the steel plate.		*Punch 2 holes of 13/16" diameter that are centered 20cm from each other and 3cm from the bottom edge of the steel plate.

			[[Image:ValveMount.png]]

YK at 23:54, 22 December 2011

2011-12-22T23:54:18Z

← Older revision		Revision as of 23:54, 22 December 2011
Line 1:		Line 1:
	{{Category=CEB press building instructions}}		{{Category=CEB press building instructions}}
	~~{{Template:CEB Press Manufacturing Instructions Navbox}}~~
	The valve mount holds the hydraulic solenoid valves to the primary arm.		The valve mount holds the hydraulic solenoid valves to the primary arm.
	<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=a239d963ea082d1a1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>
	=Tools ~~required~~=		=Tools=

	*Hole puncher with 13/16" Dies		*Hole puncher with 13/16" Dies
	*Drill Press with 1/4" or larger bit.
	~~=Materials required=~~
	*1/4"x6" flatbar: 12"
	*Solenoid Valve

	=~~Diagrams~~=		*Drill Press with 5/16" or larger bit.
	~~[[Image:valvemount.png\|thumb\|600px\|The valve mount]]~~
	=~~Fabrication instructions~~=		=Materials=
	~~#Find your hydraulic~~ solenoid valve ~~and locate its mounting holes on the back. Put~~ the plate ~~under it so~~ that the ~~mounts on the valve align~~ with the ~~top~~ of the plate.
	~~#Use spray paint to~~ mark the holes on the ~~mount's location to~~ the ~~6"x12"~~ plate~~. Center punch them.~~		*Steel plate 1/4" x 6" x 12"
	#Drill ~~the~~ holes ~~to at least a 1~~/4" ~~large (you might want to oversize them a bit, as it very difficult to get them in~~ the ~~perfect location.)~~
	#Punch 13/16" ~~holes at~~ the bottom of the plate.		*Solenoid Valve Set

			=Steps=

			*Set the steel plate on a flat surface

			*Position the solenoid valve set over the plate such that its work port surface is flush with the top edge and square with the side edges of the steel plate.

			*Using the marking utensil and the center punch, mark then center punch the 4 aligned holes at the sides of the steel plate

			*Drill 4 holes of 5/16" diameter at the marked points of the steel plate

			*Punch 2 holes of 13/16" diameter that are centered 20cm from each other and 3cm from the bottom edge of the steel plate.

Bkufa: /* Materials required */

2011-12-12T18:56:10Z

Materials required

← Older revision		Revision as of 18:56, 12 December 2011
Line 8:		Line 8:
	=Materials required=		=Materials required=
	*1/4"x6" flatbar: 12"		*1/4"x6" flatbar: 12"
			*Solenoid Valve

	=Diagrams=		=Diagrams=
	[[Image:valvemount.png\|thumb\|600px\|The valve mount]]		[[Image:valvemount.png\|thumb\|600px\|The valve mount]]

Bkufa at 18:55, 12 December 2011

2011-12-12T18:55:44Z

← Older revision		Revision as of 18:55, 12 December 2011
Line 1:		Line 1:
	{{Category=CEB press building instructions}}		{{Category=CEB press building instructions}}
	{{Template:CEB Press Manufacturing Instructions Navbox}}		{{Template:CEB Press Manufacturing Instructions Navbox}}
	~~[[Image:Valvemount.jpg\|thumb\|400px]]~~
	The valve mount holds the hydraulic solenoid valves to the primary arm.		The valve mount holds the hydraulic solenoid valves to the primary arm.
	<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=a239d963ea082d1a1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>		<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=a239d963ea082d1a1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>

Bkufa at 18:55, 12 December 2011

2011-12-12T18:55:10Z

← Older revision		Revision as of 18:55, 12 December 2011
Line 3:		Line 3:
	[[Image:Valvemount.jpg\|thumb\|400px]]		[[Image:Valvemount.jpg\|thumb\|400px]]
	The valve mount holds the hydraulic solenoid valves to the primary arm.		The valve mount holds the hydraulic solenoid valves to the primary arm.
			<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=a239d963ea082d1a1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>
	=Tools required=		=Tools required=
	*Hole puncher with 13/16" Dies		*Hole puncher with 13/16" Dies

Bkufa: /* Fabrication instructions */

2011-12-12T18:53:05Z

Fabrication instructions

← Older revision		Revision as of 18:53, 12 December 2011
Line 11:		Line 11:
	[[Image:valvemount.png\|thumb\|600px\|The valve mount]]		[[Image:valvemount.png\|thumb\|600px\|The valve mount]]
	=Fabrication instructions=		=Fabrication instructions=
	#Find your ~~Hydraulic~~ valve and locate its mounting holes on the back. Put the plate under it so that the mounts on the valve align with the top of the plate.		#Find your hydraulic solenoid valve and locate its mounting holes on the back. Put the plate under it so that the mounts on the valve align with the top of the plate.
	#Use spray paint to mark the holes on the mount's location to the ~~6x12~~ plate.		#Use spray paint to mark the holes on the mount's location to the 6"x12" plate. Center punch them.
	#Drill the holes to at least a 1/4" large (you might want to oversize them a bit, as it very difficult to get them in the perfect location.)		#Drill the holes to at least a 1/4" large (you might want to oversize them a bit, as it very difficult to get them in the perfect location.)
	#Punch 13/16 holes ~~1" in and .75" up~~ at the bottom of the plate.		#Punch 13/16" holes at the bottom of the plate.

Bkufa at 10:03, 9 October 2011

2011-10-09T10:03:50Z

← Older revision		Revision as of 10:03, 9 October 2011
Line 8:		Line 8:
	=Materials required=		=Materials required=
	*1/4"x6" flatbar: 12"		*1/4"x6" flatbar: 12"
			=Diagrams=
			[[Image:valvemount.png\|thumb\|600px\|The valve mount]]
	=Fabrication instructions=		=Fabrication instructions=
	#Find your Hydraulic valve and locate its mounting holes on the back. Put the plate under it so that the mounts on the valve align with the top of the plate.		#Find your Hydraulic valve and locate its mounting holes on the back. Put the plate under it so that the mounts on the valve align with the top of the plate.