CEB Press/Manufacturing Instructions/Wide Cylinder Supports - Revision history

Bkufa at 02:45, 16 December 2011

2011-12-16T02:45:09Z

← Older revision		Revision as of 02:45, 16 December 2011
Line 1:		Line 1:
			<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=31ebd3ea006a79211211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>
	=Tools Required=		=Tools Required=
	*Welder		*Welder

Bkufa at 08:27, 13 December 2011

2011-12-13T08:27:59Z

← Older revision		Revision as of 08:27, 13 December 2011
Line 20:		Line 20:

	=Diagrams=		=Diagrams=
			[[Image:widecylindersuppmonster.jpg\|thumb\|left\|400px\|The "monster" wide cylinder supports]]
			[[Image:widecylindersuppnorm.jpg\|thumb\|600px\|The "normal" wide cylinder supports]]
			=Fabrication Instructions=

	~~=Fabrication Instructions=~~
	~~[[Image:widecylindersuppmonster.jpg\|thumb\|left\|The "monster" wide cylinder supports]]~~
	~~[[Image:widecylindersuppnorm.jpg\|thumb\|The "normal" wide cylinder supports]]~~
	#For the "Normal CEB," torch 3/4" holes in the angle for the cylinder supports in the same manner as with the horizontal members.(19" apart, 3/4" diameter)		#For the "Normal CEB," torch 3/4" holes in the angle for the cylinder supports in the same manner as with the horizontal members.(19" apart, 3/4" diameter)
	#*For the monster, don't worry about the holes, you'll mag-drill them later.		#*For the monster, don't worry about the holes, you'll mag-drill them later.

Bkufa at 08:26, 13 December 2011

2011-12-13T08:26:26Z

← Older revision		Revision as of 08:26, 13 December 2011
Line 1:		Line 1:
			=Tools Required=
			*Welder
			*Torch
			*Punch with 3/4" dies
			*Angle Grinder
			*Speed square

			=Materials Required=
			==Monster CEB==
			*6" Light (1/4") U-Channel: 41.5" total; Wide cylinder support horizontal: 20 3/4" (2)
			*2"x2"x1/4" angle: 11.5"; Wide cylinder support verticals: 5.75" (2)
			*3/4" Steel Nuts-(2)
			*3/4" Galvanized Nuts-(2)
			==Normal CEB==
			*2"x2"x1/4" Angle: 53"
			**Wide cylinder support horizontal: 20 3/4" (2)
			**Wide cylinder support verticals: 5.75" (2)
			*3/4" Steel Nuts-(2)
			*3/4" Galvanized Nuts-(2)

			=Diagrams=

			=Fabrication Instructions=
	[[Image:widecylindersuppmonster.jpg\|thumb\|left\|The "monster" wide cylinder supports]]		[[Image:widecylindersuppmonster.jpg\|thumb\|left\|The "monster" wide cylinder supports]]
	[[Image:widecylindersuppnorm.jpg\|thumb\|The "normal" wide cylinder supports]]		[[Image:widecylindersuppnorm.jpg\|thumb\|The "normal" wide cylinder supports]]

Bkufa: Created page with "The "monster" wide cylinder supports The "normal" wide cylinder supports #For the "Norma..."

2011-12-13T08:16:32Z

Created page with "thumb|left|The "monster" wide cylinder supports thumb|The "normal" wide cylinder supports #For the "Norma..."

New page

[[Image:widecylindersuppmonster.jpg|thumb|left|The "monster" wide cylinder supports]]
[[Image:widecylindersuppnorm.jpg|thumb|The "normal" wide cylinder supports]]
#For the "Normal CEB," torch 3/4" holes in the angle for the cylinder supports in the same manner as with the horizontal members.(19" apart, 3/4" diameter)
#*For the monster, don't worry about the holes, you'll mag-drill them later.
#Weld the 2"x2" angle (5.75") centered and squared on one side of the U-Channel(for "monster") or angle (for "normal", weld it to the side without the holes).
#Torch a hole (3/4" for "normal") (1" for "monster") away from the end of the 2"x2" for a 3/4" bolt and grind it clean.
#Place a steel nut over the hole and insure it is clear for a bolt and flush.
#Weld the nut in place.
#Put a galvanized nut on a 3/4"x2.5" bolt and thread through the welded nut on each side.