CEB Press v16.09/SCAD Files/Parametric - Revision history

Dorkmo: /* To Do */

2018-06-03T17:56:30Z

To Do

← Older revision		Revision as of 17:56, 3 June 2018
Line 1,905:		Line 1,905:
	=To Do=		=To Do=

	*update with newest changes of the FreeCAD version
	*get [[Nesting_Software\|SVnest]] to work for torch table layout		*get [[Nesting_Software\|SVnest]] to work for torch table layout

2018-06-03T17:54:57Z

← Older revision		Revision as of 17:54, 3 June 2018
Line 1:		Line 1:
	'''work in progress'''		'''work in progress''' moved on to [[CEB Press v17.08/SCAD Files/]]

	creating an OpenSCAD replica of v16.09		creating an OpenSCAD replica of v16.09

2018-06-03T16:57:31Z

To Do

← Older revision		Revision as of 16:57, 3 June 2018
Line 1,906:		Line 1,906:

	*update with newest changes of the FreeCAD version		*update with newest changes of the FreeCAD version
			*get [[Nesting_Software\|SVnest]] to work for torch table layout

2018-06-03T16:39:13Z

Part Review Layout

← Older revision		Revision as of 16:39, 3 June 2018
Line 1,901:		Line 1,901:

	</nowiki>		</nowiki>


			=To Do=

			*update with newest changes of the FreeCAD version

2017-07-21T02:07:16Z

Default Variables

← Older revision		Revision as of 02:07, 21 July 2017
Line 87:		Line 87:

	a1x=4;		a1x=4;
			a1y=72; //calculate based on drawer cylinder
			a1z=aZstandard;

	a2y=6;		a2x=6;
			a2y=72; //calculate based on drawer cylinder
			a2z=aZstandard;

	a4z=aZstandard;		a4z=aZstandard;
Line 143:		Line 147:

	f4x=f5x-0.5; //same as f5 but minus 0.25 on each side to give a little overhang		f4x=f5x-0.5; //same as f5 but minus 0.25 on each side to give a little overhang


	</nowiki>		</nowiki>

2017-07-21T02:05:23Z

← Older revision		Revision as of 02:05, 21 July 2017
Line 1,207:		Line 1,207:
	use <modus.scad>;		use <modus.scad>;

	a6p(~~6,4,0.5,0.5,1~~);		a6p();

	module a6p(X,Y,Zx,Zy,W){		module a6p(){

			X=a2x;
			Y=a1x;
			Zx=a2z;
			Zy=a1z;

			W=min(((1)/cos((atan((Y-1)/(X-1))))),((1)/sin((atan((Y-1)/(X-1))))));
			//trying to make some overhang for insert to butt up against. not perfect but working
			//trying for 0.5, but not getting there exactly

	difference(){		difference(){
Line 1,218:		Line 1,227:
	rotate([0,0,atan((Y-1)/(X-1))])		rotate([0,0,atan((Y-1)/(X-1))])
	translate([0,-W,0])		translate([0,-W,0])
	cube([50,W,a6z]);		#cube([50,W,a6z]);

	cube([0.625,Zx,a6z]);		cube([0.625,Zx,a6z]);
Line 1,242:		Line 1,251:

	translate([X-Zy,Y-0.625-100,0])		translate([X-Zy,Y-0.625-100,0])
	#cube([Zy,100,a6z]);		cube([Zy,100,a6z]);



	} //end difference		} //end difference

2017-07-21T02:01:59Z

2017-07-21T02:01:04Z

2017-07-20T02:41:35Z

Default Variables

← Older revision		Revision as of 02:41, 20 July 2017
Line 91:		Line 91:

	a4z=aZstandard;		a4z=aZstandard;
			a6z=aZstandard;

	//		//
Line 143:		Line 143:

	f4x=f5x-0.5; //same as f5 but minus 0.25 on each side to give a little overhang		f4x=f5x-0.5; //same as f5 but minus 0.25 on each side to give a little overhang


	</nowiki>		</nowiki>

2017-07-20T02:36:35Z