CEB Press v17.08 Design + Function - Revision history

Marcin: /* Pressure Settings */

2017-11-03T02:15:22Z

Pressure Settings

← Older revision		Revision as of 02:15, 3 November 2017
Line 13:		Line 13:

	=Pressure Settings=		=Pressure Settings=
	The operating pressure of the machine is set using the relief valve on the power hoses from the Power Cube. To adjust the setting, use a hydraulic pressure gauge to set the machine bypass to 2500 PSI. Turn the adjustment screw in to raise the pressure, and out to loosen it. The adjustment screw is under the adjustement nut on the bypass valve. The machine is pre-set to 2500 PSI.		The operating pressure of the machine is set using the relief valve on the power hoses from the Power Cube. To adjust the setting, use a hydraulic pressure gauge to set the machine bypass to 2500 PSI. Turn the adjustment screw in to raise the pressure, and out to loosen it. The adjustment screw is under the adjustement nut on the bypass valve. The machine should be pre-set to 2500 PSI.

	The pressure sensor should be preset to 2200-2300 PSI. To set the pressure of the pressure sensor, adjust a small flathead screwdriver screw on the pressure sensor. If the pressure sensor does not trigger, lower the pressure setting. Screw in to raise pressure, and screw out to lower the pressure. The pressure sensor comes pre-set.		The pressure sensor should be preset to 2200-2300 PSI. To set the pressure of the pressure sensor, adjust a small flathead screwdriver screw on the pressure sensor. If the pressure sensor does not trigger, lower the pressure setting. Screw in to raise pressure, and screw out to lower the pressure. The pressure sensor comes pre-set.

Marcin at 06:28, 6 October 2017

2017-10-06T06:28:45Z

← Older revision		Revision as of 06:28, 6 October 2017
Line 3:		Line 3:
	The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is loaded from the top of the machine using a tractor loader from one side of the machine. The blocks are ejected on the opposite side of the machine, away from the loading side - so that machine loading and unloading can happen safely at the same time. The blocks are pressed agains the surface of the soil loading drawer, and typical operating pressure for CEBs is 2200-2300 PSI to achieve proper compreesion. No advantage in block quality is obtained by running above this pressure.		The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is loaded from the top of the machine using a tractor loader from one side of the machine. The blocks are ejected on the opposite side of the machine, away from the loading side - so that machine loading and unloading can happen safely at the same time. The blocks are pressed agains the surface of the soil loading drawer, and typical operating pressure for CEBs is 2200-2300 PSI to achieve proper compreesion. No advantage in block quality is obtained by running above this pressure.

	The ~~full sequence of pressing steps under automatic operation is found in this diagram:~~		=Wiring and Pressing Sequence=
			The following diagrams show the electrical and plumbing connections.

	<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vTizYupL4HSzjPVivhHpbWZJ5XXCtTnlOJ5G8qifOHzMQkjhNUStHOVcfCDpBdiEwP56lmXQYYRgrmW/embed?start=false&loop=false&delayms=3000#4" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>		The document also shows the full sequence of pressing steps under automatic operation.

			<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vTizYupL4HSzjPVivhHpbWZJ5XXCtTnlOJ5G8qifOHzMQkjhNUStHOVcfCDpBdiEwP56lmXQYYRgrmW/embed?start=false&loop=false&delayms=3000" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>

	[https://docs.google.com/presentation/d/1ITZPT5dSDMs_2q3t-ijj3eC7j1GWCpbe99dprmVASLQ/edit#slide=id.g27b48854a0_0_16 edit]		[https://docs.google.com/presentation/d/1ITZPT5dSDMs_2q3t-ijj3eC7j1GWCpbe99dprmVASLQ/edit#slide=id.g27b48854a0_0_16 edit]

Marcin: /* Pressure Setting */

2017-10-06T06:24:39Z

Pressure Setting

← Older revision		Revision as of 06:24, 6 October 2017
Line 9:		Line 9:
	[https://docs.google.com/presentation/d/1ITZPT5dSDMs_2q3t-ijj3eC7j1GWCpbe99dprmVASLQ/edit#slide=id.g27b48854a0_0_16 edit]		[https://docs.google.com/presentation/d/1ITZPT5dSDMs_2q3t-ijj3eC7j1GWCpbe99dprmVASLQ/edit#slide=id.g27b48854a0_0_16 edit]

	=Pressure ~~Setting~~=		=Pressure Settings=
	The operating pressure of the machine is		The operating pressure of the machine is set using the relief valve on the power hoses from the Power Cube. To adjust the setting, use a hydraulic pressure gauge to set the machine bypass to 2500 PSI. Turn the adjustment screw in to raise the pressure, and out to loosen it. The adjustment screw is under the adjustement nut on the bypass valve. The machine is pre-set to 2500 PSI.

			The pressure sensor should be preset to 2200-2300 PSI. To set the pressure of the pressure sensor, adjust a small flathead screwdriver screw on the pressure sensor. If the pressure sensor does not trigger, lower the pressure setting. Screw in to raise pressure, and screw out to lower the pressure. The pressure sensor comes pre-set.

Marcin: /* General */

2017-10-06T05:29:09Z

General

← Older revision		Revision as of 05:29, 6 October 2017
Line 6:		Line 6:

	<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vTizYupL4HSzjPVivhHpbWZJ5XXCtTnlOJ5G8qifOHzMQkjhNUStHOVcfCDpBdiEwP56lmXQYYRgrmW/embed?start=false&loop=false&delayms=3000#4" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>		<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vTizYupL4HSzjPVivhHpbWZJ5XXCtTnlOJ5G8qifOHzMQkjhNUStHOVcfCDpBdiEwP56lmXQYYRgrmW/embed?start=false&loop=false&delayms=3000#4" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>

			[https://docs.google.com/presentation/d/1ITZPT5dSDMs_2q3t-ijj3eC7j1GWCpbe99dprmVASLQ/edit#slide=id.g27b48854a0_0_16 edit]

	=Pressure Setting=		=Pressure Setting=
	The operating pressure of the machine is		The operating pressure of the machine is

Marcin at 05:28, 6 October 2017

2017-10-06T05:28:04Z

← Older revision		Revision as of 05:28, 6 October 2017
Line 3:		Line 3:
	The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is loaded from the top of the machine using a tractor loader from one side of the machine. The blocks are ejected on the opposite side of the machine, away from the loading side - so that machine loading and unloading can happen safely at the same time. The blocks are pressed agains the surface of the soil loading drawer, and typical operating pressure for CEBs is 2200-2300 PSI to achieve proper compreesion. No advantage in block quality is obtained by running above this pressure.		The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is loaded from the top of the machine using a tractor loader from one side of the machine. The blocks are ejected on the opposite side of the machine, away from the loading side - so that machine loading and unloading can happen safely at the same time. The blocks are pressed agains the surface of the soil loading drawer, and typical operating pressure for CEBs is 2200-2300 PSI to achieve proper compreesion. No advantage in block quality is obtained by running above this pressure.

	The full sequence of pressing steps is found in this diagram:		The full sequence of pressing steps under automatic operation is found in this diagram:

			<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vTizYupL4HSzjPVivhHpbWZJ5XXCtTnlOJ5G8qifOHzMQkjhNUStHOVcfCDpBdiEwP56lmXQYYRgrmW/embed?start=false&loop=false&delayms=3000#4" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>

	=Pressure Setting=		=Pressure Setting=
	The operating pressure of the machine is		The operating pressure of the machine is

Marcin: Created page with "=General= The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is..."

2017-10-06T05:15:35Z

Created page with "=General= The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is..."

New page

=General=

The OSE CEB Press is a bottom press- blocks are pressed by the main cylinder from the bottom. A soil loading drawer loads soil into the compression chamber. Soil is loaded from the top of the machine using a tractor loader from one side of the machine. The blocks are ejected on the opposite side of the machine, away from the loading side - so that machine loading and unloading can happen safely at the same time. The blocks are pressed agains the surface of the soil loading drawer, and typical operating pressure for CEBs is 2200-2300 PSI to achieve proper compreesion. No advantage in block quality is obtained by running above this pressure.

The full sequence of pressing steps is found in this diagram:

=Pressure Setting=
The operating pressure of the machine is