CEB Press v17.08 Workshop Improvement Notes - Revision history

Marcin: /* Morale */

2023-01-04T18:28:02Z

Morale

← Older revision		Revision as of 18:28, 4 January 2023
Line 18:		Line 18:
	=Morale=		=Morale=
	*Definitely people are excited, so things are good		*Definitely people are excited, so things are good
	*

Marcin at 18:48, 25 August 2017

2017-08-25T18:48:20Z

← Older revision		Revision as of 18:48, 25 August 2017
Line 5:		Line 5:
	*Tabs on top frame pieces and mid frame pieces are bowing in from the welding. Needs complete ability to weld back and forth until a good weld happens		*Tabs on top frame pieces and mid frame pieces are bowing in from the welding. Needs complete ability to weld back and forth until a good weld happens

			=CNC Cut Pattern=
			*More reinforcements are required for pieces not bending in
			*Markings on arms, both primary and secondary, should be unique so visual inspection for which part goes with which becomes easier. Today, someone took the wrong arm pair (one piece from one arm, and another piece from another) - and it wasnt' visible immediately because pieces looked the same. Unique identifiers should be added in the CNC cut itself.
			*Immediately visible markings should occur so one end of long arm pieces is easily distinguished from another end, so the steel does not need to be flipped - saving time
			*Poka yoke patterns on drawer should allow easier ability to identify which piece goes where. Right now pokayoke exists for fit itself, but metal should provide additional info (which is top, bottom - so things are not put in upside down.
	=Equipment=		=Equipment=
	*Gas went out on 1 welder during the workshop (gas solenoid issue?)		*Gas went out on 1 welder during the workshop (gas solenoid issue?)

Marcin at 18:39, 25 August 2017

2017-08-25T18:39:39Z

← Older revision		Revision as of 18:39, 25 August 2017
Line 1:		Line 1:
	=Sourcing Issues=		=Sourcing Issues=
	*2 pieces missing from CNC cutting; need to make sure that materials are available the week before the event and that they are inventoried - or we inventory our own cutting. This is the first time that a steel order was not correct - the CNC shop is at fault here.		*2 pieces missing from CNC cutting; need to make sure that materials are available the week before the event and that they are inventoried - or we inventory our own cutting. This is the first time that a steel order was not correct - the CNC shop is at fault here.
			*Solution - picking an old part of old machine (secondary arms)
	=Design=		=Design=
	*Tabs on top frame pieces and mid frame pieces are bowing in from the welding. Needs complete ability to weld back and forth until a good weld happens		*Tabs on top frame pieces and mid frame pieces are bowing in from the welding. Needs complete ability to weld back and forth until a good weld happens
Line 10:		Line 10:
	:*We are down from 6 known working to 4 known working MIGs and 3 stick welders.		:*We are down from 6 known working to 4 known working MIGs and 3 stick welders.
	:*Definite case for open source version of welder so any issue can be addressed readily. Or convert the stick welders to MIG by addition of wire feeder + gas.		:*Definite case for open source version of welder so any issue can be addressed readily. Or convert the stick welders to MIG by addition of wire feeder + gas.

			=Morale=
			*Definitely people are excited, so things are good
			*

Marcin: Created page with "=Sourcing Issues= *2 pieces missing from CNC cutting; need to make sure that materials are available the week before the event and that they are inventoried - or we inventory..."

2017-08-25T18:38:27Z

Created page with "=Sourcing Issues= *2 pieces missing from CNC cutting; need to make sure that materials are available the week before the event and that they are inventoried - or we inventory..."

New page

=Sourcing Issues=
*2 pieces missing from CNC cutting; need to make sure that materials are available the week before the event and that they are inventoried - or we inventory our own cutting. This is the first time that a steel order was not correct - the CNC shop is at fault here.

=Design=
*Tabs on top frame pieces and mid frame pieces are bowing in from the welding. Needs complete ability to weld back and forth until a good weld happens

=Equipment=
*Gas went out on 1 welder during the workshop (gas solenoid issue?)
*Gas was already out on 1 welder, but that wasn't checked prior to the workshop. Tighter quality control on welders needs to happen before workshop.
:*We are down from 6 known working to 4 known working MIGs and 3 stick welders.
:*Definite case for open source version of welder so any issue can be addressed readily. Or convert the stick welders to MIG by addition of wire feeder + gas.