CNCCMV2/Structure/Blocks - Revision history

YK at 21:33, 18 May 2012

2012-05-18T21:33:57Z

← Older revision		Revision as of 21:33, 18 May 2012
Line 49:		Line 49:
	*Drill all holes		*Drill all holes

	=Fabricate X ~~Major~~ Block=		=Fabricate X Block=

	*[[Image: XMajorBlockV2.jpg\|300px]]		*[[Image: XMajorBlockV2.jpg\|300px]]
Line 64:		Line 64:

	*Tap required holes.		*Tap required holes.

	~~=Fabricate X Minor Block=~~

	*[[Image: XMinorBlockV2.jpg\|300px]]

	*[[File: XMinorBlockV2.pdf]]

	*Qty=2		*Qty=2
Line 81:		Line 75:
	*Tap required holes.		*Tap required holes.

	=Fabricate Y ~~Major~~ Block=		=Fabricate Y Block=

	*[[Image: YMajorBlockV2.jpg\|300px]]		*[[Image: YMajorBlockV2.jpg\|300px]]

	*[[File: YMajorBlockV2.pdf]]		*[[File: YMajorBlockV2.pdf]]

	*Qty=1

	*Match drill with the Narrow Template.

	*Match drill with the Wide Template.

	*Mark the remaining holes.

	*Drill all holes to their appropriate diameters.

	*Tap required holes.

	~~=Fabricate Y Minor Block=~~

	*[[Image: YMinorBlockV2.jpg\|300px]]

	*[[File: YMinorBlockV2.pdf]]

	*Qty=1		*Qty=1
Line 133:		Line 109:
	*Tap required holes.		*Tap required holes.

	=Fabricate Z ~~Major~~ Block=		=Fabricate Z Block=

	*[[Image: ZMajorBlockV2.jpg\|300px]]		*[[Image: ZMajorBlockV2.jpg\|300px]]

	*[[File: ZMajorBlockV2.pdf]]		*[[File: ZMajorBlockV2.pdf]]

	*Qty=1

	*Match drill with the Wide Template.

	*Mark the remaining holes.

	*Drill all holes to their appropriate diameters.

	~~=Fabricate Z Minor Block=~~

	*[[Image: ZMinorBlockV2.jpg\|300px]]

	*[[File: ZMinorBlockV2.pdf]]

	*Qty=1		*Qty=1

2012-04-29T04:32:08Z

Fabricate Narrow Template

2012-04-29T04:31:54Z

← Older revision		Revision as of 04:31, 29 April 2012
Line 18:		Line 18:

	*When clamping templates and components for match drilling, ensure that the datum edges of the template are appropriately positioned relative to the component to be drilled.		*When clamping templates and components for match drilling, ensure that the datum edges of the template are appropriately positioned relative to the component to be drilled.

			=Fabricate Narrow Template=

			[[Image: NarrowTemplateV2.jpg\|300px]]

			*[[File: NarrowTemplateV2.pdf]]

	=Fabricate Wide Template=		=Fabricate Wide Template=
Line 25:		Line 31:
	*[[File: WideTemplateV2.pdf]]		*[[File: WideTemplateV2.pdf]]

	~~=Fabricate~~ Narrow Template=		*Mark datum lines for the Narrow Template.

	~~[[Image: NarrowTemplateV2.jpg\|300px]]~~		*Match drill with the Narrow Template.

	*~~[[File: NarrowTemplateV2~~.~~pdf]]~~

	=Fabricate Platform=		=Fabricate Platform=

2012-04-28T23:05:21Z

← Older revision		Revision as of 23:05, 28 April 2012
Line 14:		Line 14:

	*All pilot holes to be tapped M5x0.8 should have a diameter of 4.5mm		*All pilot holes to be tapped M5x0.8 should have a diameter of 4.5mm

			=Template-Component Clamping: Datum Edge Orientation=

			*When clamping templates and components for match drilling, ensure that the datum edges of the template are appropriately positioned relative to the component to be drilled.

	=Fabricate Wide Template=		=Fabricate Wide Template=

2012-04-28T22:12:23Z

2012-04-28T20:28:54Z

Fabricate Wide Template

2012-04-28T18:16:32Z

Fabricate Narrow Template

← Older revision		Revision as of 18:16, 28 April 2012
Line 25:		Line 25:
	=Fabricate Narrow Template=		=Fabricate Narrow Template=

			[[Image: NarrowTemplateV2.jpg\|300px]]

			*[[File: NarrowTemplateV2.pdf]]
	*

	*

	=Fabricate Platform=		=Fabricate Platform=

2012-04-28T16:31:26Z

← Older revision		Revision as of 16:31, 28 April 2012
Line 14:		Line 14:

	*All pilot holes to be tapped M5x0.8 should have a diameter of 4.5mm		*All pilot holes to be tapped M5x0.8 should have a diameter of 4.5mm

			=Fabricate Wide Template=



			*

			*

			=Fabricate Narrow Template=



			*

			*

	=Fabricate Platform=		=Fabricate Platform=

2012-04-27T17:59:52Z

← Older revision		Revision as of 17:59, 27 April 2012
Line 10:		Line 10:

	*After drilling each hole, tap it and screw in an M5 screw for secure mounting for drilling and superior alignment.		*After drilling each hole, tap it and screw in an M5 screw for secure mounting for drilling and superior alignment.

			=M5 Pilot Holes=

			*All pilot holes to be tapped M5x0.8 should have a diameter of 4.5mm

	=Fabricate Platform=		=Fabricate Platform=

2012-04-26T21:30:54Z

← Older revision		Revision as of 21:30, 26 April 2012
Line 1:		Line 1:
			=Marking the Sleeve Bearing Mount Holes=

			*Mark 6.5mm from the circumference of the 18mm hole for each sleeve bearing mount hole.

			*Drawing a centerline may be helpful to measure along.

			=Drilling the Leadscrew Nut Mount Holes=

			*Match drill the leadscrew nut mount holes from the leadscrew nut to the block while the leadscrew nut is fitted inside the block for superior alignment.

			*After drilling each hole, tap it and screw in an M5 screw for secure mounting for drilling and superior alignment.

	=Fabricate Platform=		=Fabricate Platform=