Cold Saw/Build Instructions/Swivel - Revision history

YK at 20:57, 19 June 2012

2012-06-19T20:57:38Z

← Older revision		Revision as of 20:57, 19 June 2012
Line 4:		Line 4:

	Measure, mark, pilot drill, and drill the swivel hole.		Measure, mark, pilot drill, and drill the swivel hole.

			http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Swivel_Plate

	=Shaft Blocks=		=Shaft Blocks=

	Clamp two Shaft Blocks onto the table, one on top of the other and oriented to drill the shaft hole.		Clamp two Shaft Blocks onto the table, one on top of the other and oriented to drill the shaft hole.

			http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Shaft_Block

	Measure, mark, pilot drill, and drill the shaft hole, match drilling into the shaft block underneath.		Measure, mark, pilot drill, and drill the shaft hole, match drilling into the shaft block underneath.

YK at 20:47, 19 June 2012

2012-06-19T20:47:53Z

← Older revision		Revision as of 20:47, 19 June 2012
Line 22:		Line 22:

	Tack weld and weld the Shaft Blocks to the Swivel Plate.		Tack weld and weld the Shaft Blocks to the Swivel Plate.

			=Threaded Rod=

			Clamp the Base Plate to the table.

			Place the Swivel Plate on top of the Base Plate and align the swivel holes by inserting the Short Threaded Rod into the swivel holes of the Swivel Plate and Base Plate.

			Clamp the Swivel Plate to the Base Plate.

			Clamp the Short Threaded Rod so as to facilitate welding the Short Threaded Rod to the Swivel Plate from the top, with a small gap from the top surface.

			Tack weld and weld the Short Threaded Rod to the Swivel Plate.

YK at 20:42, 19 June 2012

2012-06-19T20:42:51Z

← Older revision		Revision as of 20:42, 19 June 2012
Line 14:		Line 14:

	Measure, mark, drill, counterbore, and tap the stopper hole.		Measure, mark, drill, counterbore, and tap the stopper hole.

			=Shaft Blocks to Swivel Plate=

			Clamp the Shaft Blocks to the Swivel Plate's rear, such that their outer faces along the shaft axis are less than 130mm and also that the shaft blocks are approximately parallel to the Swivel Plate's faces.

			Insert the Shaft into the Shaft Blocks for alignment.

			Tack weld and weld the Shaft Blocks to the Swivel Plate.

YK: Created page with "=Swivel Plate= Clamp the Swivel Plate onto the table. Measure, mark, pilot drill, and drill the swivel hole. =Shaft Blocks= Clamp two Shaft Blocks onto the table, one on top ..."

2012-06-19T20:39:55Z

Created page with "=Swivel Plate= Clamp the Swivel Plate onto the table. Measure, mark, pilot drill, and drill the swivel hole. =Shaft Blocks= Clamp two Shaft Blocks onto the table, one on top ..."

New page

=Swivel Plate=

Clamp the Swivel Plate onto the table.

Measure, mark, pilot drill, and drill the swivel hole.

=Shaft Blocks=

Clamp two Shaft Blocks onto the table, one on top of the other and oriented to drill the shaft hole.

Measure, mark, pilot drill, and drill the shaft hole, match drilling into the shaft block underneath.

Clamp a Shaft Block, oriented to drill the stopper hole.

Measure, mark, drill, counterbore, and tap the stopper hole.