Cold Saw/V1 Design Files/Swivel Plate - Revision history

YK: /* Swivel Plate */

2012-06-15T22:54:28Z

Swivel Plate

← Older revision		Revision as of 22:54, 15 June 2012
Line 1:		Line 1:
	=Swivel Plate=		=Swivel Plate=

	*'''Length: ~~457~~.~~2mm~~''' (Long enough to support the drive assembly such that the blade is centered on the vise)		*'''Length: 406.4mm''' (Long enough to support the drive assembly such that the blade is centered on the vise)

	*'''Width: 203.2mm''' (Wide enough to fit the shaft blocks wide enough to support the drive assembly such that the blade is centered on the vise)		*'''Width: 203.2mm''' (Wide enough to fit the shaft blocks wide enough to support the drive assembly such that the blade is centered on the vise)

	*'''Thickness: 25.4mm'''		*'''Thickness: 25.4mm'''



	*'''Swivel Hole Diameter: 30mm'''		*'''Swivel Hole Diameter: 30mm'''

	*'''Swivel Hole Along Length; ~~400mm from~~ Edge'''		*'''Swivel Hole Along Length; Near Edge'''

	*'''Swivel Hole Spacing Along Width: Centered'''		*'''Swivel Hole Spacing Along Width: Centered'''


	*'''Support Hole Diameter: 12mm with 20mm dia 13 deep countersink'''

	*'''Support Hole Rectangle: 30mm x 55mm'''

	*'''Support Hole Rectangle Positioning: Centered, 140mm apart center to center.'''

	*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''

YK: /* Swivel Plate */

2012-06-12T16:49:03Z

Swivel Plate

← Older revision		Revision as of 16:49, 12 June 2012
Line 1:		Line 1:
	=Swivel Plate=		=Swivel Plate=

	*'''Length: 457.2mm'''		*'''Length: 457.2mm''' (Long enough to support the drive assembly such that the blade is centered on the vise)

	*'''Width: 203.2mm''' (Wide enough to fit the shaft blocks wide enough to support the drive assembly such that the blade is centered on the vise)		*'''Width: 203.2mm''' (Wide enough to fit the shaft blocks wide enough to support the drive assembly such that the blade is centered on the vise)

YK: /* Swivel Plate */

2012-06-12T16:48:33Z

Swivel Plate

← Older revision		Revision as of 16:48, 12 June 2012
Line 3:		Line 3:
	*'''Length: 457.2mm'''		*'''Length: 457.2mm'''

	*'''Width: ~~304~~.~~8mm~~'''		*'''Width: 203.2mm''' (Wide enough to fit the shaft blocks wide enough to support the drive assembly such that the blade is centered on the vise)

	*'''Thickness: 25.4mm'''		*'''Thickness: 25.4mm'''
Line 19:		Line 19:
	*'''Support Hole Rectangle: 30mm x 55mm'''		*'''Support Hole Rectangle: 30mm x 55mm'''

	*'''Support Hole Rectangle Positioning: Centered, ~~150mm~~ apart center to center.'''		*'''Support Hole Rectangle Positioning: Centered, 140mm apart center to center.'''

	*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''		*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''

YK: /* Swivel Plate */

2012-06-12T15:29:47Z

Swivel Plate

← Older revision		Revision as of 15:29, 12 June 2012
Line 19:		Line 19:
	*'''Support Hole Rectangle: 30mm x 55mm'''		*'''Support Hole Rectangle: 30mm x 55mm'''

	*'''Support Hole Rectangle ~~Spacing~~: ~~Around a corner~~, 150mm apart center to center.'''		*'''Support Hole Rectangle Positioning: Centered, 150mm apart center to center.'''

	*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''		*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''



	*'''2D Image'''		*'''2D Image'''

YK: /* Swivel Plate */

2012-06-11T23:57:00Z

Swivel Plate

← Older revision		Revision as of 23:57, 11 June 2012
Line 10:		Line 10:
	*'''Swivel Hole Diameter: 30mm'''		*'''Swivel Hole Diameter: 30mm'''

	*'''Swivel Hole Along Length; ~~50mm~~ from Edge'''		*'''Swivel Hole Along Length; 400mm from Edge'''

	*'''Swivel Hole Spacing Along Width: Centered'''		*'''Swivel Hole Spacing Along Width: Centered'''

YK: /* Swivel Plate */

2012-06-11T23:56:47Z

Swivel Plate

← Older revision		Revision as of 23:56, 11 June 2012
Line 20:		Line 20:

	*'''Support Hole Rectangle Spacing: Around a corner, 150mm apart center to center.'''		*'''Support Hole Rectangle Spacing: Around a corner, 150mm apart center to center.'''



	*'''Clamp Hole Diameter: 10.5mm dia, then M12x1.75 tapped'''

	*'''Clamp Hole Spacing Along Width: 185mm''' (Swivel Hole Spacing Along Width)

	*'''Clamp Hole Spacing Along Height: 12.7mm''' (Swivel Plate Thickness / 2)


	*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''		*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''

	*'''Clamp Hole Notes: The swivel clamp fastens horizontally such that the swivel plate does not bend within the disc tolerance. A plate has excellent performance along its length and width, but not vertical forces against


	*'''2D Image'''		*'''2D Image'''

YK: /* Swivel Plate */

2012-06-11T23:47:14Z

Swivel Plate

← Older revision		Revision as of 23:47, 11 June 2012
Line 10:		Line 10:
	*'''Swivel Hole Diameter: 30mm'''		*'''Swivel Hole Diameter: 30mm'''

	*'''Swivel Hole Along Length; ~~25mm~~ from Edge'''		*'''Swivel Hole Along Length; 50mm from Edge'''

	*'''Swivel Hole Spacing Along Width: Centered'''		*'''Swivel Hole Spacing Along Width: Centered'''

YK: /* Swivel Plate */

2012-06-11T23:46:57Z

Swivel Plate

← Older revision		Revision as of 23:46, 11 June 2012
Line 8:		Line 8:


	*'''Swivel Hole Diameter: ~~153mm~~'''		*'''Swivel Hole Diameter: 30mm'''

	*'''Swivel Hole ~~Spacing~~ Along Length~~: 335mm~~'''		*'''Swivel Hole Along Length; 25mm from Edge'''

	*'''Swivel Hole Spacing Along Width: ~~185mm~~'''		*'''Swivel Hole Spacing Along Width: Centered'''

YK: /* Swivel Plate */

2012-06-07T20:34:39Z

Swivel Plate

← Older revision		Revision as of 20:34, 7 June 2012
Line 31:		Line 31:

	*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''		*'''Support Hole Notes: The Support holes must be positioned such that the blade is centered at the vise. The blade should be centered at the vise so that angled cuts are facilitated in both directions (angling to both left and right). The Support holes should also leave enough space between the Shaft Blocks such that a thrust washer and clamping shaft collar can fit in between (and be easily maintained).'''

			*'''Clamp Hole Notes: The swivel clamp fastens horizontally such that the swivel plate does not bend within the disc tolerance. A plate has excellent performance along its length and width, but not vertical forces against

YK: /* Swivel Plate */

2012-06-04T23:30:58Z

Swivel Plate

← Older revision		Revision as of 23:30, 4 June 2012
Line 25:		Line 25:
	*'''Clamp Hole Diameter: 10.5mm dia, then M12x1.75 tapped'''		*'''Clamp Hole Diameter: 10.5mm dia, then M12x1.75 tapped'''

	*'''Clamp Hole Spacing Along Width: ~~190mm~~''' (Swivel Hole Spacing Along Width)		*'''Clamp Hole Spacing Along Width: 185mm''' (Swivel Hole Spacing Along Width)

	*'''Clamp Hole Spacing Along Height: 12.7mm''' (Swivel Plate Thickness / 2)		*'''Clamp Hole Spacing Along Height: 12.7mm''' (Swivel Plate Thickness / 2)