D3D Mega v23.05 Calculations - Revision history

Alexa: /* Bed Lift */

2023-11-08T23:59:02Z

Bed Lift

@@ Line 1: / Line 1: @@
 ==Bed Lift==
 Using 8 total 8mm universal axes on the Z axis, the printer is calculated to be able to lift up to 72lbs max before belt skipping occurs. With the bed weighing in at roughly 30-40lbs, there will be a minimum of 30lbs left for lifting the print. See [[GT2 Belts]] for notes on lifting power. Adding counterweights as was done in the [[D3D Giga]] build could enable prints up to the full 72lbs.
 ==Heated Chamber==

Alexa: Add links

2023-09-23T03:49:28Z

Add links

← Older revision		Revision as of 03:49, 23 September 2023
Line 4:		Line 4:
	==Heated Chamber==		==Heated Chamber==
	[https://web.archive.org/web/20221005061820/https://engineering.stackexchange.com/questions/16840/how-thick-do-i-need-to-make-the-insulation-in-my-homemade-furnace Breakdown of calculating insulation]		[https://web.archive.org/web/20221005061820/https://engineering.stackexchange.com/questions/16840/how-thick-do-i-need-to-make-the-insulation-in-my-homemade-furnace Breakdown of calculating insulation]


			= Links =

			[[D3D Mega v23.05]]

Alexa: Add link, sections

2023-09-16T17:29:16Z

Add link, sections

← Older revision		Revision as of 17:29, 16 September 2023
Line 1:		Line 1:
			==Bed Lift==
	Using 8 total 8mm universal axes on the Z axis, the printer is calculated to be able to lift up to 72lbs max before belt skipping occurs. With the bed weighing in at roughly 30-40lbs, there will be a minimum of 30lbs left for lifting the print. See [[GT2 Belts]] for notes on lifting power. Adding counterweights as was done in the [[D3D Giga]] build could enable prints up to the full 72lbs.		Using 8 total 8mm universal axes on the Z axis, the printer is calculated to be able to lift up to 72lbs max before belt skipping occurs. With the bed weighing in at roughly 30-40lbs, there will be a minimum of 30lbs left for lifting the print. See [[GT2 Belts]] for notes on lifting power. Adding counterweights as was done in the [[D3D Giga]] build could enable prints up to the full 72lbs.

			==Heated Chamber==
			[https://web.archive.org/web/20221005061820/https://engineering.stackexchange.com/questions/16840/how-thick-do-i-need-to-make-the-insulation-in-my-homemade-furnace Breakdown of calculating insulation]

Alexa: Added note on bed lift capacity.

2023-07-09T09:09:57Z

Added note on bed lift capacity.

← Older revision		Revision as of 09:09, 9 July 2023
Line 1:		Line 1:
	Using 8 total 8mm universal axes on the Z axis, the printer is calculated to be able to lift up to 72lbs max before belt skipping occurs. With the bed weighing in at roughly 30-40lbs, there will be a minimum of 30lbs left for lifting the print. See [[GT2 Belts]] for notes on lifting power.		Using 8 total 8mm universal axes on the Z axis, the printer is calculated to be able to lift up to 72lbs max before belt skipping occurs. With the bed weighing in at roughly 30-40lbs, there will be a minimum of 30lbs left for lifting the print. See [[GT2 Belts]] for notes on lifting power. Adding counterweights as was done in the [[D3D Giga]] build could enable prints up to the full 72lbs.

Alexa: Create page

2023-05-22T02:02:02Z

Create page

New page

Using 8 total 8mm universal axes on the Z axis, the printer is calculated to be able to lift up to 72lbs max before belt skipping occurs. With the bed weighing in at roughly 30-40lbs, there will be a minimum of 30lbs left for lifting the print. See [[GT2 Belts]] for notes on lifting power.