D3D Pro v23.12 Troubleshooting and Repair - Revision history

Alexa at 12:33, 6 July 2024

2024-07-06T12:33:36Z

← Older revision		Revision as of 12:33, 6 July 2024
Line 5:		Line 5:
	---		---

	{{log\|date=2024/06/26\|time=11:23pm\|note=Pen Case \| Trying old print settings to see if recent changes are the cause of the print failures. Removed large clog at start of print (likely from previous print). Used the top of the extruder stepper motor for leverage when using pliers to remove clogged filament. Failed - underextrusion @ ~25mm up.}}		{{log\|date=2024/06/26\|time=11:23pm\|note=Pen Case - Trying old print settings to see if recent changes are the cause of the print failures. Removed large clog at start of print (likely from previous print). Used the top of the extruder stepper motor for leverage when using pliers to remove clogged filament. Failed - underextrusion @ ~25mm up.}}

	---		---

Alexa: Finish through 2024/06/26

2024-07-06T12:33:21Z

Finish through 2024/06/26

← Older revision		Revision as of 12:33, 6 July 2024
Line 2:		Line 2:
	=Print & Maintenance Log=		=Print & Maintenance Log=
	<nowiki>{{log\|date=\|time=\|note=}}</nowiki>		<nowiki>{{log\|date=\|time=\|note=}}</nowiki>

			---

			{{log\|date=2024/06/26\|time=11:23pm\|note=Pen Case \| Trying old print settings to see if recent changes are the cause of the print failures. Removed large clog at start of print (likely from previous print). Used the top of the extruder stepper motor for leverage when using pliers to remove clogged filament. Failed - underextrusion @ ~25mm up.}}

			---

	{{log\|date=2024/06/25\|time=11:11pm\|note=Failed - '''Lost Z Steps'''}}		{{log\|date=2024/06/25\|time=11:11pm\|note=Failed - '''Lost Z Steps'''}}

Alexa: Finish through 2024/06/25

2024-07-06T12:15:58Z

Finish through 2024/06/25

@@ Line 2: / Line 2: @@
 =Print & Maintenance Log=
 <nowiki>{{log|date=|time=|note=}}</nowiki>
 {{log|date=2024/06/24|time=11:49pm|note=Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. '''X axis belt clamp is too low - damaging prints.''' Failure - Bed adhesion, underextrusion, filament stripping.}}

Alexa at 12:03, 6 July 2024

2024-07-06T12:03:08Z

← Older revision		Revision as of 12:03, 6 July 2024
Line 1:		Line 1:
			{{RightTOC}}
	=Print & Maintenance Log=		=Print & Maintenance Log=
	<nowiki>{{log\|date=\|time=\|note=}}</nowiki>		<nowiki>{{log\|date=\|time=\|note=}}</nowiki>
Line 17:		Line 18:

	{{log\|date=2024/06/24\|time=10:24pm\|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}		{{log\|date=2024/06/24\|time=10:24pm\|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}


	~~{{RightTOC}}~~

Alexa at 12:02, 6 July 2024

2024-07-06T12:02:49Z

← Older revision		Revision as of 12:02, 6 July 2024
Line 17:		Line 17:

	{{log\|date=2024/06/24\|time=10:24pm\|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}		{{log\|date=2024/06/24\|time=10:24pm\|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}


			{{RightTOC}}

Alexa: Finish through 2024/06/24

2024-07-06T12:01:26Z

Finish through 2024/06/24

← Older revision		Revision as of 12:01, 6 July 2024
Line 1:		Line 1:
	=Print & Maintenance Log=		=Print & Maintenance Log=
			<nowiki>{{log\|date=\|time=\|note=}}</nowiki>

			{{log\|date=2024/06/24\|time=11:49pm\|note=Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. '''X axis belt clamp is too low - damaging prints.''' Failure - Bed adhesion, underextrusion, filament stripping.}}

			{{log\|date=2024/06/24\|time=11:46pm\|note=Blackjack Shoe Plate 2 - probing failed, bed misaligned}}

			{{log\|date=2024/06/24\|time=11:43pm\|note=Failure to heat bed - M112 error}}

			{{log\|date=2024/06/24\|time=11:38pm\|note=R.T.T.P. - turned off linear advance @ ~10% - Print looking okay at 60% - some underextrusion early on. Print successful! Horizontal artiface appears in a repeating pattern every 7mm. (Primarily cosmetic issue). Printed this model in incorrect orientation}}

			{{log\|date=2024/06/24\|time=11:11pm\|note=R.T.T.P. - Paused @ skirt for stripped filament. Failed @ 5-10%. Stripped filament}}

			{{log\|date=2024/06/24\|time=11:08pm\|note=R.T.T.P. - Speed too high? Seemingly exceeding max volumetric flow rate. Failed - underextrusion}}

			{{log\|date=2024/06/24\|time=10:45pm\|note=Ringing tower test print - Cancelled - Forgot to adjust min. layer time}}

	{{log\|date=2024/06/24\|time=10:24pm\|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}		{{log\|date=2024/06/24\|time=10:24pm\|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}

Alexa: Create new data collection page

2024-07-06T11:47:47Z

Create new data collection page

New page

=Print & Maintenance Log=

{{log|date=2024/06/24|time=10:24pm|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}}