D3D v18.07 - Revision history

Marcin: /* BOM */

2018-08-15T15:21:02Z

BOM

← Older revision		Revision as of 15:21, 15 August 2018
Line 20:		Line 20:

	=BOM=		=BOM=
	*[[D3D_v18.06_BOM]] - main		*Same as [[D3D_v18.06_BOM]] - main
	*Extruder BOM - [[D3D_Extruder#BOM]] - v18.07 - proven.		*Extruder BOM - [[D3D_Extruder#BOM]] - v18.07 - proven.

2018-08-02T18:22:18Z

CAD

← Older revision		Revision as of 18:22, 2 August 2018
Line 17:		Line 17:

	*Updated file with sensor holder moved down - https://wiki.opensourceecology.org/wiki/File:Extruder_modification.fcstd		*Updated file with sensor holder moved down - https://wiki.opensourceecology.org/wiki/File:Extruder_modification.fcstd
	*

			=BOM=
			*[[D3D_v18.06_BOM]] - main
			*Extruder BOM - [[D3D_Extruder#BOM]] - v18.07 - proven.

	=Build=		=Build=
	==Extruder Build==		==Extruder Build==

2018-07-26T20:06:00Z

Jul 26, 2018

← Older revision		Revision as of 20:06, 26 July 2018
Line 50:		Line 50:

	<html><iframe src="https://www.facebook.com/plugins/post.php?href=https%3A%2F%2Fwww.facebook.com%2Fmarcin.jakubowski.378%2Fposts%2F10214136807991353&width=500" width="500" height="688" style="border:none;overflow:hidden" scrolling="no" frameborder="0" allowTransparency="true" allow="encrypted-media"></iframe></html>		<html><iframe src="https://www.facebook.com/plugins/post.php?href=https%3A%2F%2Fwww.facebook.com%2Fmarcin.jakubowski.378%2Fposts%2F10214136807991353&width=500" width="500" height="688" style="border:none;overflow:hidden" scrolling="no" frameborder="0" allowTransparency="true" allow="encrypted-media"></iframe></html>

			'''Proposed Solution for Smooth Motion with Soft Rods'''
			*Oil-filled bushings. See [[8 mm Rods]].
			*Lubrication - for heat and speed
			*Speed optimization - set max speed for fast travel so when going above 400%, we don't exceed a fast value such as 200mm/sec.
			*Set travel speed to no more than print speed - to optimize for fast printing where travel is only a small part of a print - and we care more about rod longevity based on lifetime design goals.

	==Jul 24, 2018==		==Jul 24, 2018==

2018-07-26T19:56:39Z

Data Collection

← Older revision		Revision as of 19:56, 26 July 2018
Line 47:		Line 47:

	=Data Collection=		=Data Collection=
			==Jul 26, 2018==

			<html><iframe src="https://www.facebook.com/plugins/post.php?href=https%3A%2F%2Fwww.facebook.com%2Fmarcin.jakubowski.378%2Fposts%2F10214136807991353&width=500" width="500" height="688" style="border:none;overflow:hidden" scrolling="no" frameborder="0" allowTransparency="true" allow="encrypted-media"></iframe></html>

			==Jul 24, 2018==
	*Bottom layer speed increased from 20 to 40		*Bottom layer speed increased from 20 to 40
	*Top/bottom speed increased from 15 to 25		*Top/bottom speed increased from 15 to 25

2018-07-26T16:52:38Z

Code Notes

← Older revision		Revision as of 16:52, 26 July 2018
Line 12:		Line 12:

	=Code Notes=		=Code Notes=
	*Turned on EEPROM in latest version so that we can save the Z offset settings between runs, as Z offset can drift slowly.		*Turned on EEPROM in latest version so that we can save the Z offset settings between runs, as Z offset can drift slowly. This keeps the updated version of offset in place.

	=CAD=		=CAD=

2018-07-26T16:52:18Z

Development Template

← Older revision		Revision as of 16:52, 26 July 2018
Line 10:		Line 10:

	<html><iframe width="700" height="370" src="https://osedev.org/graph/weekly/burndown/D3D%20v1807?start=6/18/2018"></iframe></html>		<html><iframe width="700" height="370" src="https://osedev.org/graph/weekly/burndown/D3D%20v1807?start=6/18/2018"></iframe></html>

			=Code Notes=
			*Turned on EEPROM in latest version so that we can save the Z offset settings between runs, as Z offset can drift slowly.

	=CAD=		=CAD=

2018-07-26T16:51:35Z

Data Collection

← Older revision		Revision as of 16:51, 26 July 2018
Line 48:		Line 48:
	*Min and max speed of fan set to 100		*Min and max speed of fan set to 100
	*Set up SD card support as at [[RepRap Discount Smart Controller]]		*Set up SD card support as at [[RepRap Discount Smart Controller]]
	*After running at 400%, 8 mm 12L14 ultra machinable rods are getting pitted.		*After running at 400%, 8 mm 12L14 ultra machinable rods are getting pitted. The left connector for stepper motors burned out - I suspect it was the added resistance of moving the motors that drew extra current for a meltdown. Then about 10 minutes into the print, the print would stop - motors stalling slowly to a dead stop. Then the temperature error set once motors stopped moving. Essentially, power to the board stopped when the plug melted.

	=Future Work=		=Future Work=

	*Live height adjustment in Marlin - tune first layer until exactness after bed level correction		*Live height adjustment in Marlin - tune first layer until exactness after bed level correction

2018-07-26T10:49:57Z

Data Collection

← Older revision		Revision as of 10:49, 26 July 2018
Line 48:		Line 48:
	*Min and max speed of fan set to 100		*Min and max speed of fan set to 100
	*Set up SD card support as at [[RepRap Discount Smart Controller]]		*Set up SD card support as at [[RepRap Discount Smart Controller]]
			*After running at 400%, 8 mm 12L14 ultra machinable rods are getting pitted.

	=Future Work=		=Future Work=

	*Live height adjustment in Marlin - tune first layer until exactness after bed level correction		*Live height adjustment in Marlin - tune first layer until exactness after bed level correction

2018-07-25T12:22:02Z

Data Collection

← Older revision		Revision as of 12:22, 25 July 2018
Line 48:		Line 48:
	*Min and max speed of fan set to 100		*Min and max speed of fan set to 100
	*Set up SD card support as at [[RepRap Discount Smart Controller]]		*Set up SD card support as at [[RepRap Discount Smart Controller]]

			=Future Work=

			*Live height adjustment in Marlin - tune first layer until exactness after bed level correction

2018-07-25T11:44:04Z

Data Collection

← Older revision		Revision as of 11:44, 25 July 2018
Line 47:		Line 47:
	*Amazing quality results at 125%, going up		*Amazing quality results at 125%, going up
	*Min and max speed of fan set to 100		*Min and max speed of fan set to 100
			*Set up SD card support as at [[RepRap Discount Smart Controller]]