D3D v20.04 Software - Revision history

Marcin: /* Updates */

2020-04-26T16:28:55Z

Updates

← Older revision		Revision as of 16:28, 26 April 2020
Line 11:		Line 11:
	*#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed.		*#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed.
	*#define Z_MAX_POS 400 - increase z		*#define Z_MAX_POS 400 - increase z
			#define HOMING_FEEDRATE_Z (1260) - changed this from 4*60

	=Profile=		=Profile=

Marcin: /* Updates */

2020-04-26T15:51:59Z

Updates

← Older revision		Revision as of 15:51, 26 April 2020
Line 10:		Line 10:
	=Updates=		=Updates=
	*#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed.		*#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed.
			*#define Z_MAX_POS 400 - increase z

	=Profile=		=Profile=

Marcin: /* Firmware */

2020-04-26T15:51:06Z

Firmware

← Older revision		Revision as of 15:51, 26 April 2020
Line 1:		Line 1:


	=Firmware=		=Firmware=
	*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.		*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.
Line 5:		Line 7:
	*Note that we also need to use D3D Universal E steps per mm -M92 E100		*Note that we also need to use D3D Universal E steps per mm -M92 E100
	*Note we need to make sure we move over 80 mm after G28 so probe is over bed		*Note we need to make sure we move over 80 mm after G28 so probe is over bed

			=Updates=
			*#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed.

	=Profile=		=Profile=

Marcin: /* Firmware */

2020-04-24T04:32:55Z

Firmware

← Older revision		Revision as of 04:32, 24 April 2020
Line 1:		Line 1:
	=Firmware=		=Firmware=
	*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.		*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.
	*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: ~~endstop_reversing~~ was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]		*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_inverting was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]
	*'''New file with versioning is thus: [[File:Marlin_D3D_Pro_2.zip]]'''		*'''New file with versioning is thus: [[File:Marlin_D3D_Pro_2.zip]]'''
	*Note that we also need to use D3D Universal E steps per mm -M92 E100		*Note that we also need to use D3D Universal E steps per mm -M92 E100

Marcin: /* Firmware */

2020-04-24T04:17:07Z

Firmware

← Older revision		Revision as of 04:17, 24 April 2020
Line 2:		Line 2:
	*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.		*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.
	*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]		*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]
	*New file: [[File:Marlin_D3D_Pro_2.zip]]		*'''New file with versioning is thus: [[File:Marlin_D3D_Pro_2.zip]]'''
	*Note that we also need to use D3D Universal E steps per mm -M92 E100		*Note that we also need to use D3D Universal E steps per mm -M92 E100
	*Note we need to make sure we move over 80 mm after G28 so probe is over bed		*Note we need to make sure we move over 80 mm after G28 so probe is over bed

Marcin: /* Firmware */

2020-04-20T07:11:57Z

Firmware

← Older revision		Revision as of 07:11, 20 April 2020
Line 5:		Line 5:
	*Note that we also need to use D3D Universal E steps per mm -M92 E100		*Note that we also need to use D3D Universal E steps per mm -M92 E100
	*Note we need to make sure we move over 80 mm after G28 so probe is over bed		*Note we need to make sure we move over 80 mm after G28 so probe is over bed

			=Profile=
			*[[File:d3d_pro_2.ini]]
			*G0 Z330 takes bed down - but why was it 330 (12"+) in the 8" printers? This is taken from the older printer profiles.

	=Links=		=Links=
	*[[D3D v20.04]]		*[[D3D v20.04]]

Marcin: /* Firmware */

2020-04-20T06:57:50Z

Firmware

← Older revision		Revision as of 06:57, 20 April 2020
Line 3:		Line 3:
	*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]		*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]
	*New file: [[File:Marlin_D3D_Pro_2.zip]]		*New file: [[File:Marlin_D3D_Pro_2.zip]]
			*Note that we also need to use D3D Universal E steps per mm -M92 E100
			*Note we need to make sure we move over 80 mm after G28 so probe is over bed

	=Links=		=Links=
	*[[D3D v20.04]]		*[[D3D v20.04]]

Marcin at 06:32, 20 April 2020

2020-04-20T06:32:06Z

← Older revision		Revision as of 06:32, 20 April 2020
Line 3:		Line 3:
	*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]		*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]
	*New file: [[File:Marlin_D3D_Pro_2.zip]]		*New file: [[File:Marlin_D3D_Pro_2.zip]]

			=Links=
			*[[D3D v20.04]]

Marcin: Created page with "=Firmware= *Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. File:Marlin_D3D_Pro_v1.0.zip no longer works...."

2020-04-20T06:31:50Z

Created page with "=Firmware= *Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. File:Marlin_D3D_Pro_v1.0.zip no longer works...."

New page

=Firmware=
*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works.
*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_reversing was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]]
*New file: [[File:Marlin_D3D_Pro_2.zip]]