Ron Broberg: moved Edison Battery Manufacture to Edison Battery/Manufacture

2011-07-18T22:44:33Z

moved Edison Battery Manufacture to Edison Battery/Manufacture

← Older revision	Revision as of 22:44, 18 July 2011
(No difference)

Ron Broberg: Created page with "A description of of the nickel-iron Edison Battery, including its manufacture, was published in 1924 by the Edison Storage Battery Company as the..."

2011-07-15T15:18:29Z

Created page with "A description of of the nickel-iron Edison Battery, including its manufacture, was published in 1924 by the Edison Storage Battery Company as the..."

New page

A description of of the [[nickel-iron_battery| nickel-iron]] [[Edison Battery]], including its manufacture, was published in 1924 by the [[Edison Storage Battery Company]] as the book "The ''Edison alkaline storage battery.''" This is an excerpt from pages 13-24. There are numerous illustrations in the original not yet reproduced here. Note that the 'flat' mesh cells of earlier models have been replaced, in the case of the negative iron oxide anode, by a helical twisted cylinder.

http://books.google.com/books?id=IKIgAAAAMAAJ&pg=PA13

==A Trip Through the Factory==

PERHAPS the easiest way to describe the manufacture of the Edison Storage Battery
is to take the reader in imagination, through the factory at Orange. Let us, therefore,
enter the "Million Cell Plant" of the Edison Storage Battery Company, to observe
the ingenious machines and processes that Mr. Edison found it necessary to invent,
and to perfect, before the nickel-iron-alkaline storage battery could be made
in commercial quantities.

One of the first Edison Batteries to be put on the market was the 150 ampere hour size
suitable for operating delivery wagons, passenger electrics and similar types of small cars.
This was known as the Type A4 and since then the output of the factory has been estimated
in "A4 equivalents." The buildings and their present equipment have a capacity of over 3,000
"A4 equivalents" per 10 hour day — a million "A4 equivalents" per year. Mr. Edison, however,
looks upon this as only a nucleus of the business awaiting development and ample room has been left
in the concrete structures with their nine acres of floor space for extension in every department.

In being shown the construction of the cell the first things to take up arc, naturally,
the "plates" that hold the active materials — nickel hydrate in perforated steel tubes
for the positive, and iron oxide in perforated steel pockets for the negative.

These perforated steel pockets and perforated steel tubes are made from cold rolled carbon steel ribbon
which passes between two rollers. One roller has small projections on its surface;
the other roller corresponding depressions. The ribbon comes out filled with regular rows
of rectangular perforations, so small that 560 are included in one square inch.
This perforating is necessary so that the potash solution may come in contact with
the iron oxide and the nickel hydrate, and the necessary chemical action take place.

To remove any little burrs that might remain after the perforating process,
the ribbon is ground by emery wheels that smooth the rough side. But, emery dust gets
into the little perforations, and to clean them the ribbon is fed through a machine
with six revolving wire brushes. As it zig-zags up and down, on its way through the machine,
two brushes rub one side, two the other side, and two brush cross-wise—the ribbon emerges
with every perforation perfectly clean.

The ribbon is then nickel-plated. It is drawn from a reel and travels in and out
through a series of tanks containing respectively, a potash solution; hot water;
a double solution of nickel ammonium sulphate; hot water; cold water; and ammonium hydroxide.
Pulley wheels located above and in the bottoms of the tanks guide it, the lower wheel being made
of non-conducting material. The potash solution removes all oil and grease; the hot water removes
the potash; the double solution of nickel ammonium sulphate is the nickelplating bath;
the hot water again washes it and dissolves any salts that may have lodged in the perforations;
the cold water removes what the hot water does not; and the ammonium hydroxide removes all trace
of acid that may remain from the nickel-plating bath.

Traveling in and out through a series of baths, the perforated steel ribbon is subjected
to a continuous nickel-plating process.

From ribbon to completed tube in one operation. Each machine makes ~20,000 tubes a day.

It takes eight minutes for a given point on the ribbon to pass through the entire process.

After being nickel-plated the ribbon is dried. This prevents any rust forming during
the brief interval before it goes to the annealing furnaces.

From the drying oven it is placed in a crucible. The crucible is hermetically sealed
and as much air exhausted as possible. The crucible is put in an oil-burning furnace.
To prevent oxidation or discoloring of the nickel-plated material, while under the action
of the extreme heat of the furnace, a stream of hydrogen gas is constantly passed
through the crucible, keeping the ribbon in an "inert" atmosphere.

All steel parts used in the Edison Cell are annealed in this manner. In the annealing process
the nickel-plating is fused or welded to the steel itself. Thus it becomes an integral part
of the steel and removes the possibility of the nickel coating pealing off or being chipped off.

Before being nickel-plated and after being annealed the ribbon is weighed and micrometer readings
taken to make certain that the nickel is properly deposited.

The ribbon is prepared in two widths, the narrower being used for the negative or iron oxide pocket.
The negative pockets are formed in halves not unlike the well-known paper scarf-pin box
in which the box proper and cover are approximately equal, one fitting over the other.
Groups of punches cut the ribbon to required length and stamp the halves into form.
The halves are then slid together, forming the pockets. One end is left open for filling with iron oxide.

The ribbon for the positive tube is fed automatically into a machine through a shaping die
that not only forms it spirally into a tube ]/i inch in diameter, but laps the edges
of the ribbon over each other, forming a perfect joint. This lappedover seam is pressed fiat or swedged,
and as a last-operation, the tube is cut to correct length (41/9 inches). In some of these machines
the tubes are wound to the right, in others they are wound to the left. The purpose of making
these tubes in "rights" and "lefts" will be explained later.

It is customary for a workman to have had six months' experience in setting the forming dies
of this machine before he can make it produce a normal output of 20,000 tubes a day.
The positive tube is ready to be filled. Ordinarily to fill it with nickel hydrate would be
neither difficult nor interesting, but there are certain electrical characteristics wanted
that gave Mr. Edison many sleepless nights before they were obtained.

The electricity in flowing through the solution from the positive element (nickel hydrate)
to the negative element (iron oxide) causes the oxygen in the iron oxide to come over to the
nickel hydrate. This oxidizes the hydrate and forms nickel oxide or peroxide. This nickel oxide
has comparatively high electrical resistance, so it is advisable to divide it up into very thin layers
and to conduct the electricity to these layers by intervening layers of metal.

Pure nickel is not difficult to obtain, but to get it in the form required for loading the positive tube,
is an original and interesting process.

After a multitude of experiments to obtain a layer of thin conducting metal that would prove
satisfactory electrically and yet have as long a life as the rest of the battery,
the plan was conceived of using "flakes" of nickel which could be loaded into the tubes
the same as the nickel hydrate but which, when tamped down, would give the desired conducting element.
The processes for manufacturing this nickel flake are perhaps the most interesting in the factory.

A traveling crane carrying 10 revolving copper cylinders is shown on the opposite page.
The cylinders are lowered into two parallel rows of 5 copper baths each corresponding
to the 10 cylinders, where a very thin film of copper is deposited on them. Then they are lifted out
and travel past multiple water jets that spray them thoroughly before they are lowered
into a row of nickel baths where a film of nickel, approximately ^^-0 [sic] inch thick,
is deposited over the copper.

Then they travel back to the copper baths pausing at the water jets for another thorough spraying.
This operation is repeated until there are 125 films of copper and 125 films of nickel.

The time the cylinders should remain in the nickel bath is accurately regulated by a circuit breaker
and ampere hour meter combined to automatically permit only sufficient current to pass to deposit
a nickel film of the correct thickness. The length of time required to give the copper coating
is not so important. It takes about five hours to make one 250 layer sheet .0075 inch thick.

The sheet is removed from the cylinder; cut into pieces 1/16 inch square and the pieces put
into a solution where the copper is dissolved leaving thin films of pure metallic nickel.
After thorough washing and the forcing out of the water by centrifugal machines similar to sugar driers,
the nickel is dried over steam coils, screened and sent to the tube-loading machines—the thinnest,
lightest, pure metal product ever used in a manufacturing process, nickel" snow-flake.''

It would take 85 flakes, placed one on top of the other, to equal the thickness of the paper
used in this book, and a bushel weighs only 4 1/2 pounds.

Drilling the positive tubes is the next operation. Again it was found to be necessary to
provide machinery of special design. The tubes are taken eight at a time and a little metal cap
is inserted in the bottom of each. They are then placed in a mould and the mould placed in the machine
directly under a row of fixed tubes through which metal rods pass. The tube-loading machines are also
equipped with two hoppers; one hopper dumps a specific quantity of nickel hydrate, the other dumps
a specific quantity of nickel flake. Then, with a force of 2,000 pounds per square inch,
the metal rods ram the layers down. This process is automatically repeated until there are
over 300 alternate layers (about 630 layers in all) in a tube only 4 1/2 inches in length.
As each tube becomes fully loaded, the machine automatically stops the plunger for that particular tube.

To make certain that the tubefilling machines are alternating accurately, one tube is taken from
every lot filled, sawed longitudinally, and put under the microscope. (A magnified section is shown
on this page.) Should the filling be improperly done, the error is detected promptly and that
lot of tubes rejected.

Early experiment showed that the oxidizing of the hydrate had a tendency to cause the tubes to swell.
To overcome this absolutely, each tube is reinforced with eight seamless steel rings,
equidistantly spaced.

These little rings are punched, ten at a time, from a ribbon of highest grade finished cold rolled steel.
This steel is made especially for the Edison Storage Battery Company for this particular job;
if made too soft or too hard it will not do. The ribbon travels from a reel through the press
to another reel on which, after the rings are punched out, it is wound as "scrap."

On its way through the punch the ribbon pauses as dies descend and punch out ten holes. Then it advances
and when the dies descend again to punch out another ten holes the first ten have arrived at another row
of dies which force down the inside edges of the holes making rims, or flanges, equal in depth to that
of the desired rings. The dies that force down the edges are encircled with a hard steel shell
that reaches the ribbon 1/16" behind the dies and cuts off the rim.

It is interesting to note that the sheet steel from which the rings are made is thinner than the width
of the bands. These rings, before being used, are nickel-plated and fed into a machine that
automatically discards any that are imperfect.

The filled tubes and the seamless rings are put into another automatic machine. The rings gravitate
into 8 equidistant grooves in such a position that the tube can be forced through them by
a plunger working from the side.

After being closed, trimmed and inspected, 30 of these positive tubes are mounted on a nickel-plated
steel grid and pressed into permanent position by hydraulic pressure of 40 tons. You will remember these
tubes were made in "rights" and "lefts." They are mounted alternately in the grid so that any tendency
to twist on the part of one tube will be counteracted by the next one which is oppositely wound.

For a Type A4 Edison Cell four positive plates are mounted on a steel rod, to which has been attached
a vertical pole, the plates being equidistantly spaced by means of steel washers. Similarly are mounted
five negative plates. "Intermesh" the four positive and five negative plates so that they will be
alternately negative and positive, keep these plates from touching by putting hard rubber rods or
pin insulators between them, fit hard rubber ladder pieces or grid separators to the edges of the plates,
and the elements are assembled and ready to place in their container.

The container is made of nickel-plated sheet steel with sides corrugated to increase its strength.
The single side seam, is welded by the oxy-acetylene blowpipe and the tops and bottom welded on
in the same manner.

The assembled elements are now placed in the container with thin sheets of hard rubber, on the sides
not already insulated by the grid separators. A hard rubber washer is dropped on each of the vertical
pole pieces, and the cell is ready to have the top welded on. It is not necessary to see
the inside of the cell again.

The fittings through which the vertical poles pass are provided with soft rubber washers,
and with rings and gland caps for expanding these soft rubber washers to form a gas-tight
and liquid-tight packing between the top of the container and the poles.

The top of a Type A4 Cell with cover welded on is shown on this page. The aperture for putting
in solution, or adding distilled water is in the valve box in the center. In the top of the lid is
a little valve which allows the gas generated during charging to get out, but no impurities or air
can get in.

When any storage battery is charged, hydrogen gas forms on the negative plates and oxygen gas
on the positive. These gases, in the form of minute bubbles, rise to the surface of the solution and,
being lighter than air, float away.

Edison Battery/Manufacture - Revision history

Ron Broberg: moved Edison Battery Manufacture to Edison Battery/Manufacture

Ron Broberg: Created page with "A description of of the nickel-iron Edison Battery, including its manufacture, was published in 1924 by the Edison Storage Battery Company as the..."