Electronic Design Guidelines - Revision history

Ron Broberg at 17:30, 16 July 2011

2011-07-16T17:30:19Z

← Older revision		Revision as of 17:30, 16 July 2011
Line 17:		Line 17:

	[[Category: Electronics]]		[[Category: Electronics]]
			[[Category: CAD]]

Ron Broberg at 17:28, 16 July 2011

2011-07-16T17:28:07Z

← Older revision		Revision as of 17:28, 16 July 2011
Line 3:		Line 3:
	Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible.		Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible.

	Choosing a common set of components to use where possible will help with fabrication. We can share these symbols and footprints so designing is faster. Designs should be done in open source software KiCAD or Gnu Electronic Design Automation tools.		Choosing a common set of components to use where possible will help with fabrication. We can share these symbols and footprints so designing is faster. Designs should be done in open source software [http://www.lis.inpg.fr/realise_au_lis/kicad/\| KiCAD] or [http://www.gpleda.org/index.html\| Gnu Electronic Design Automation] tools.

	Look at existing designs and try to use the same components.		Look at existing designs and try to use the same components.

Ron Broberg at 14:52, 14 July 2011

2011-07-14T14:52:56Z

← Older revision		Revision as of 14:52, 14 July 2011
Line 15:		Line 15:

	Standard connector for solenoid control terminals		Standard connector for solenoid control terminals

			[[Category: Electronics]]

Josh Jordan at 16:31, 7 July 2011

2011-07-07T16:31:15Z

← Older revision		Revision as of 16:31, 7 July 2011
Line 7:		Line 7:
	Look at existing designs and try to use the same components.		Look at existing designs and try to use the same components.
	http://opensourceecology.org/wiki/Replication_of_CEB_Controller		http://opensourceecology.org/wiki/Replication_of_CEB_Controller

			This is a list of circuits we need: http://opensourceecology.org/wiki/Electronics_List

	Standard connectors:		Standard connectors:

	Standard connector for 12V output and input		Standard connector for 12V output and input

	Standard connector for solenoid control terminals		Standard connector for solenoid control terminals

Josh Jordan at 16:29, 7 July 2011

2011-07-07T16:29:39Z

← Older revision		Revision as of 16:29, 7 July 2011
Line 1:		Line 1:
			[[Category: Digital Fabrication]]

	Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible.		Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible.

Josh Jordan at 16:27, 7 July 2011

2011-07-07T16:27:35Z

← Older revision		Revision as of 16:27, 7 July 2011
Line 4:		Line 4:

	Look at existing designs and try to use the same components.		Look at existing designs and try to use the same components.
			http://opensourceecology.org/wiki/Replication_of_CEB_Controller

	Standard connectors:		Standard connectors:
	Standard connector for 12V output and input		Standard connector for 12V output and input
	Standard connector for solenoid control terminals		Standard connector for solenoid control terminals

Josh Jordan: Created page with "Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible. Choosing a common se..."

2011-07-06T00:34:23Z

Created page with "Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible. Choosing a common se..."

New page

Electronic designs should be as simple as possible and be programmable if possible. Use the AVR ATMEGA if possible so the design can be arduino compatible.

Choosing a common set of components to use where possible will help with fabrication. We can share these symbols and footprints so designing is faster. Designs should be done in open source software KiCAD or Gnu Electronic Design Automation tools.

Look at existing designs and try to use the same components.

Standard connectors:
Standard connector for 12V output and input
Standard connector for solenoid control terminals