FreeCAD Log - Revision history

Marcin: /* Fri Jun 2, 2017 */

2017-06-03T03:19:42Z

Fri Jun 2, 2017

← Older revision		Revision as of 03:19, 3 June 2017
Line 2:		Line 2:

	=Fri Jun 2, 2017=		=Fri Jun 2, 2017=
			Issue - while this looks fine in principle, zooming in shows broken lines at edges. This uses [[Roberto Log]] macro, [[File:Iso_view.FCMacro]] to extract the iso views, scale 8. Also, line width in the macro was 0.3 - changing to 0.1 does not change anything.

	[[File:jaggedlines.jpg\|500px]]		[[File:jaggedlines.jpg\|500px]]

Marcin at 03:14, 3 June 2017

2017-06-03T03:14:31Z

← Older revision		Revision as of 03:14, 3 June 2017
Line 1:		Line 1:
			{{Hint\|This is a log for troubleshooting and improving FreeCAD. Anyone can post.}}

	=Fri Jun 2, 2017=		=Fri Jun 2, 2017=

Marcin: /* Fri Jun 2, 2017 */

2017-06-03T03:02:14Z

Fri Jun 2, 2017

← Older revision		Revision as of 03:02, 3 June 2017
Line 1:		Line 1:
	=Fri Jun 2, 2017=		=Fri Jun 2, 2017=

	[[File:jaggedlines.jpg]]		[[File:jaggedlines.jpg\|500px]]

	=Wed Jun 17, 2015=		=Wed Jun 17, 2015=

Marcin at 03:00, 3 June 2017

2017-06-03T03:00:25Z

← Older revision		Revision as of 03:00, 3 June 2017
Line 1:		Line 1:
			=Fri Jun 2, 2017=

			[[File:jaggedlines.jpg]]

	=Wed Jun 17, 2015=		=Wed Jun 17, 2015=
	Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it. Managed to draw tubes, rotate, and copy them - but the instructions on the [[FreeCAD Wiki]] do not appear to do the things they say should happen. Aligning corners is the next frontier, and copying them reliably. Bug report: need to switch between navigation styles within a drawing to activate certain features.		Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it. Managed to draw tubes, rotate, and copy them - but the instructions on the [[FreeCAD Wiki]] do not appear to do the things they say should happen. Aligning corners is the next frontier, and copying them reliably. Bug report: need to switch between navigation styles within a drawing to activate certain features.

	[[Category:FreeCAD]]		[[Category:FreeCAD]]

Marcin at 04:04, 30 December 2015

2015-12-30T04:04:45Z

← Older revision		Revision as of 04:04, 30 December 2015
Line 1:		Line 1:
	=Wed Jun 17, 2015=		=Wed Jun 17, 2015=
	Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it. Managed to draw tubes, rotate, and copy them - but the instructions on the [[FreeCAD Wiki]] do not appear to do the things they say should happen. Aligning corners is the next frontier, and copying them reliably. Bug report: need to switch between navigation styles within a drawing to activate certain features.		Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it. Managed to draw tubes, rotate, and copy them - but the instructions on the [[FreeCAD Wiki]] do not appear to do the things they say should happen. Aligning corners is the next frontier, and copying them reliably. Bug report: need to switch between navigation styles within a drawing to activate certain features.

			[[Category:FreeCAD]]

Marcin at 19:17, 18 June 2015

2015-06-18T19:17:09Z

← Older revision		Revision as of 19:17, 18 June 2015
Line 1:		Line 1:
	=Wed Jun 17, 2015=		=Wed Jun 17, 2015=
	Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it.		Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it. Managed to draw tubes, rotate, and copy them - but the instructions on the [[FreeCAD Wiki]] do not appear to do the things they say should happen. Aligning corners is the next frontier, and copying them reliably. Bug report: need to switch between navigation styles within a drawing to activate certain features.

Marcin: Created page with "=Wed Jun 17, 2015= Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug rep..."

2015-06-18T19:14:57Z

Created page with "=Wed Jun 17, 2015= Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug rep..."

New page

=Wed Jun 17, 2015=
Experience so far is that the interface is very frustrating. Key difficulty is how to activate different functions. Many times they are blanked out. Bug report: drawing buttons in workbenches deactivate, and the only way to get them to activate is to switch out of a workbench and get back into it.