G-Code Generation - Revision history

Marcin: /* G Code Generation for 3D Printing */

2018-12-22T04:46:47Z

G Code Generation for 3D Printing

← Older revision		Revision as of 04:46, 22 December 2018
Line 1:		Line 1:
			=Basic Anatomy=

			TO generate a sample g-coded file from scratch for testing motion only on D3D :

			#Home Axes -
			##G28 X0 Y0 - just x and y
			#Start moving -
			##G1 X50 Y50
			##G1 X150 Y50
			##G1 X50 Y50
			##G1 X150 Y50

			This just moves the x axis back and forth

			When it comes to extruding - read on.

	=G Code Generation for 3D Printing=		=G Code Generation for 3D Printing=
	*G code generation for 3D printing is nontrivial because you also have to specify how much filament to extrude		*G code generation for 3D printing is nontrivial because you also have to specify how much filament to extrude

Marcin: Marcin moved page G Code Generation to G-Code Generation

2018-12-22T04:27:45Z

Marcin moved page G Code Generation to G-Code Generation

← Older revision

Revision as of 04:27, 22 December 2018

Marcin at 16:08, 8 December 2018

2018-12-08T16:08:14Z

← Older revision		Revision as of 16:08, 8 December 2018
Line 25:		Line 25:
	Which means -- at this point, I don't think this printer has the capacity to complete the burn-in test at any speed, let alone a 16-motor production print.		Which means -- at this point, I don't think this printer has the capacity to complete the burn-in test at any speed, let alone a 16-motor production print.

	[[File:actualprintarea.jpg]]		[[File:actualprintarea.jpg\|400px]]

Marcin at 16:03, 8 December 2018

2018-12-08T16:03:48Z

← Older revision		Revision as of 16:03, 8 December 2018
Line 24:		Line 24:

	Which means -- at this point, I don't think this printer has the capacity to complete the burn-in test at any speed, let alone a 16-motor production print.		Which means -- at this point, I don't think this printer has the capacity to complete the burn-in test at any speed, let alone a 16-motor production print.

			[[File:actualprintarea.jpg]]

Marcin: Created page with "=G Code Generation for 3D Printing= *G code generation for 3D printing is nontrivial because you also have to specify how much filament to extrude I found that manually writ..."

2018-12-08T16:00:35Z

Created page with "=G Code Generation for 3D Printing= *G code generation for 3D printing is nontrivial because you also have to specify how much filament to extrude I found that manually writ..."

New page

=G Code Generation for 3D Printing=
*G code generation for 3D printing is nontrivial because you also have to specify how much filament to extrude

I found that manually writing gcode for the suggested "burn in test" print was nontrivial. A few example lines of gcode taken from test-cube.gcode look like this:

G1 X110.200 Y110.200 E2.00144

G1 X93.000 Y110.200 E2.32498

G1 X93.000 Y93.000 E2.64853

It's all straightforward until you get to E -- this is a measure of how much filament to extrude in mm. But it is additive -- so the file starts at 0 and increases continuously until the end of the file. Slicer programs like CURA do the work of calculating the E value for each movement.

I found I could calculate a value (length of axis movement times layer height times layer width) -- but doing so for the entirety of the file seemed like more work than it was worth. Is there a trick I'm missing?

I also attempted making a file in FreeCAD but had trouble getting a 3D shape with width from my sketch -- my FreeCAD skills are like 1/10.

So anyway, then I googled it: https://www.thingiverse.com/thing:2779287 and thought this should work just fine.

The initial test on my printer shows me that my print area is less than the full 8-inch square bed. Photo attached shows my print area limits.

The front limit (right side of photo) is due to the X-axis motor hitting up against the front frame. The right limit (top side of photo) is less clear -- my extruder refuses to move any further along the X-axis but I don't visually see anything obstructing its motion. The distance left on the axis is about 1 inch.

Which means -- at this point, I don't think this printer has the capacity to complete the burn-in test at any speed, let alone a 16-motor production print.