Genie Door Opener Programming - Revision history

Marcin at 04:23, 18 March 2026

2026-03-18T04:23:16Z

@@ Line 3: / Line 3: @@
 #To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.
 #Make sure you are in the unlocked position on the wall console to start programming.
-#Hit the program button for a few seconds. Blue light will turn on.
+#Hit the program button for a few seconds. Blue light will turn on. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.
-#Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.
+#Press down the down (-) button - move the door into the closed position, using down and up as needed for adjustment. Do not go too far, you may just crush the door. '''Critical: you have only 30 seconds to do this before timeout!''' (Not sure whether it is 30 seconds of inactivity, or 30 seconds total - check)
-Move the door into the closed position, using down and up as needed for adjustment. Do not go too far, you may just crush the door.
+Further adjustment of limits:
-'''Critical: you have only 30 seconds to do this before timeout!''' (Not sure whether it is 30 seconds of inactivity, or 30 seconds total - check)
+Battery Backup Unit:
+#Battery backup unit - install it with power to the head off.
-When door is in fully closed position - hit the 'set' button (the third button).
+#Quality control: once wired, LEDs light on the motion sensors. Wall unit lights up. Light can be switched on and off on the wall unit. Can lock the opener on the wall unit. Meaning it will not move.

Marcin at 04:05, 18 March 2026

2026-03-18T04:05:02Z

← Older revision		Revision as of 04:05, 18 March 2026
Line 1:		Line 1:
	More info in [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit#slide=id.g3331bf0e34a_0_0 work doc].		More info in [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit#slide=id.g3331bf0e34a_0_0 work doc].

	To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.		#To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.
			#Make sure you are in the unlocked position on the wall console to start programming.
	Make sure you are in the unlocked position on the wall console to start programming.		#Hit the program button for a few seconds. Blue light will turn on.
			#Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.
	Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.

	Move the door into the closed position, using down and up as needed for adjustment. Do not go too far, you may just crush the door.		Move the door into the closed position, using down and up as needed for adjustment. Do not go too far, you may just crush the door.

Marcin at 05:13, 8 March 2025

2025-03-08T05:13:01Z

← Older revision		Revision as of 05:13, 8 March 2025
Line 1:		Line 1:
			More info in [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit#slide=id.g3331bf0e34a_0_0 work doc].

	To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.		To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.

Marcin at 05:11, 8 March 2025

2025-03-08T05:11:51Z

@@ Line 1: / Line 1: @@
 To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.
 Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.
@@ Line 18: / Line 20: @@
 Heavier than normal blockage reverses the lowering - such as someone or something trapped under door. Blockage stops motion when raising.

Marcin at 05:08, 8 March 2025

2025-03-08T05:08:19Z

@@ Line 1: / Line 1: @@
-To program, open the door half way.
+To program, open the door half way. Lock turnbuckle in holder. Use a belt-drive door opener, so that the belt can be 3D printed later on.
 Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.
@@ Line 6: / Line 6: @@
 '''Critical: you have only 30 seconds to do this before timeout!''' (Not sure whether it is 30 seconds of inactivity, or 30 seconds total - check)

Marcin: Created page with "To program, open the door half way. Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release but..."

2025-03-08T05:03:09Z

Created page with "To program, open the door half way. Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release but..."

New page

To program, open the door half way.

Press down the down (-) button long. It does not matter what the light scheme in the indicator lights is. After 2 second hold, release button, and blue light will flash.

Move the door into the closed position, using down and up as needed for adjustment. Do not go too far, you may just crush the door.

'''Critical: you have only 30 seconds to do this before timeout!''' (Not sure whether it is 30 seconds of inactivity, or 30 seconds total - check)