Industrial Robot Electrical Design - Revision history

Syk0saje: Redirected page to Industrial Robot/Research Development

2012-01-28T11:40:18Z

Redirected page to Industrial Robot/Research Development

← Older revision		Revision as of 11:40, 28 January 2012
Line 1:		Line 1:
	#REDIRECT [[Industrial Robot Development]]		#REDIRECT [[Industrial Robot/Research Development]]

YK: organizing into main ind. robot pages, redirect added to main dev page

2011-07-20T07:12:03Z

organizing into main ind. robot pages, redirect added to main dev page

← Older revision		Revision as of 07:12, 20 July 2011
Line 1:		Line 1:
	[[~~Category:~~ Industrial Robot]]		#REDIRECT [[Industrial Robot Development]]

	~~=Solenoid Driver=~~

	The function of the solenoid driver is to power on and off the solenoid valves. The solenoid driver receives a pulse width modulation signal from the microcontroller and amplifies that signal; the amplified signal is a DC output that energizes the solenoid valve.

	~~Possibility is the PWM Driver 1.1 from RepRap wiki [http://reprap.org/wiki/PWM_Driver_1_1?sortcol=0&table=1&up=1 PWM Driver 1.1]~~

	~~=Stepper Motor Driver=~~

	~~The function of the stepper motor driver is to power the stepper motors in discrete increments; the stepper motor shaft then rotates based on how much energy was provided by the stepper motor driver.~~

	~~More information on stepper motor controllers can be found in the following link; the design contained in that link is the one planned to be used for the industrial robot. [[Stepper Motor Controller]]~~

	~~Off-the-Shelf options include [http://www.sparkfun.com/products/10267 EasyDriver on sparkfun] and [http://www.pololu.com/catalog/product/1201 A4983 Stepper Motor Driver on pololu]~~

	~~=Shaft Encoder=~~

	~~[http://mechatronics.mech.northwestern.edu/design_ref/sensors/encoders.html Mechatronics on Digital Encoders]~~

	~~[http://en.wikipedia.org/wiki/Rotary_encoder Wikipedia on Rotary Encoders]~~

	The function of the shaft encoder is to determine the position of a motor shaft as time passes. This function is necessary for the industrial robot to perform tasks with accuracy, because the robot's movement is determined not only by the power supplied to the motors but also the load being moved. For instance, more power is required to lift a boulder than a baseball. It is easier, more practical, and more accurate to have a position sensor (shaft encoder) than having to calculate different power inputs for each load.

	An absolute encoder can identify different positions of the measured shaft, but is more complex than an incremental encoder. However, an incremental encoder only provides relative position information. An incremental encoder can be used as an "absolute" one by saving the relative movement information; for instance, for day 1, joint A moves 5 degrees clockwise from the home position, then day 2, joint A moves 10 more degrees clockwise; by saving the information from day 1, the microcontroller can understand that joint A has moved a total of 15 degrees clockwise from the home position, not just 10 degrees.

	~~[http://translate.google.com/translate?js=y&prev=_t&hl=en&ie=UTF-8&layout=1&eotf=1&u=http://sites.google.com/site/proyectosroboticos/encoder Resource for Incremental Encoder Design]~~

	~~[http://www.societyofrobots.com/sensors_encoder.shtml Society of Robots on Incremental Encoder Design]~~

	~~The current development plan is to use incremental encoders for their low cost, high resolution, and simplicity of design and fabrication relative to absolute encoders.~~

	~~Incremental encoders can be split into 2 types: magnetic and optical. The current plan is to use optical encoders.~~

	~~A phototransistor pair can be found here [http://parts.digikey.com/ca/1/43466-opto-sensor-dual-pkg-slot-type-ee-sx1031.html Digikey PT pair]~~

	Combining that with schmidt trigger'd comparators, 2 digital outputs can carry signals to the microcontroller, one output to determine direction of shaft rotation and the other output to determine speed of shaft rotation. (if output B changes when output A is high, the shaft is rotating in one direction; if output B changes when output A is low, the shaft is rotating in the other direction).

	~~[http://thedenneys.org/pub/robot/encoders/ Denneys on optical incremental encoders~~]

YK: organizing into main ind. robot pages

2011-07-20T07:10:52Z

organizing into main ind. robot pages

← Older revision		Revision as of 07:10, 20 July 2011
Line 1:		Line 1:
	~~=Electrical Design Illustrated Overview=~~

	~~[[Image:RobotElecOverview.png\|790px]]~~

	~~=Toolchain for Toolpaths=~~

	Electrical Schematic Designer (gschem) > export ( __ filetype)> PCB Layout Creator (PCB) > export (gerber filetype)> G-code generator from gerber files (PCB2gcode) > export (gcode filetype) > Machine Controller (EMC2) > export (logic signals) > Machine ( __ ) > export (work)

	[[Category: Industrial Robot]]		[[Category: Industrial Robot]]

	~~=Micro-controller=~~

	The microcontroller is the programmable command unit of the industrial robot. The microcontroller can send signals to the stepper motor drivers and solenoid drivers to move the robot; the microcontroller can receive signals from the shaft encoder to determine how far the robot has moved at each of the 6 joints.

	~~Possibility is an Arduino microcontroller (such as the Arduino Mega 2560) [http://www.arduino.cc/ Arduino Website]~~

	~~The microcontroller will need 6 analog outputs with PWM to give signals to the solenoid drivers.~~

	~~The microcontroller will need X ___ outputs ___ to give signals to the stepper motor drivers.~~

	~~The microcontroller will need X ___ inputs ___ to receive signals from the shaft encoders.~~

	~~The microcontroller will need a universal serial bus (USB) port to interface with the computer.~~

	=Solenoid Driver=		=Solenoid Driver=

YK: /* Stepper Motor Driver */

2011-06-07T21:31:28Z

Stepper Motor Driver

← Older revision		Revision as of 21:31, 7 June 2011
Line 35:		Line 35:
	More information on stepper motor controllers can be found in the following link; the design contained in that link is the one planned to be used for the industrial robot. [[Stepper Motor Controller]]		More information on stepper motor controllers can be found in the following link; the design contained in that link is the one planned to be used for the industrial robot. [[Stepper Motor Controller]]

	Off-the-Shelf options include [http://www.sparkfun.com/products/10267 EasyDriver on sparkfun]		Off-the-Shelf options include [http://www.sparkfun.com/products/10267 EasyDriver on sparkfun] and [http://www.pololu.com/catalog/product/1201 A4983 Stepper Motor Driver on pololu]

	=Shaft Encoder=		=Shaft Encoder=

YK: /* Stepper Motor Driver */ Added off-the-shelf item

2011-06-07T21:22:39Z

Stepper Motor Driver: Added off-the-shelf item

← Older revision		Revision as of 21:22, 7 June 2011
Line 34:		Line 34:

	More information on stepper motor controllers can be found in the following link; the design contained in that link is the one planned to be used for the industrial robot. [[Stepper Motor Controller]]		More information on stepper motor controllers can be found in the following link; the design contained in that link is the one planned to be used for the industrial robot. [[Stepper Motor Controller]]

			Off-the-Shelf options include [http://www.sparkfun.com/products/10267 EasyDriver on sparkfun]

	=Shaft Encoder=		=Shaft Encoder=

YK: /* Shaft Encoder */ Added resource, brief function explanation

2011-06-07T21:11:40Z

Shaft Encoder: Added resource, brief function explanation

← Older revision		Revision as of 21:11, 7 June 2011
Line 51:		Line 51:
	The current development plan is to use incremental encoders for their low cost, high resolution, and simplicity of design and fabrication relative to absolute encoders.		The current development plan is to use incremental encoders for their low cost, high resolution, and simplicity of design and fabrication relative to absolute encoders.

	Incremental encoders can be split into 2 types: magnetic and optical.		Incremental encoders can be split into 2 types: magnetic and optical. The current plan is to use optical encoders.

			A phototransistor pair can be found here [http://parts.digikey.com/ca/1/43466-opto-sensor-dual-pkg-slot-type-ee-sx1031.html Digikey PT pair]

			Combining that with schmidt trigger'd comparators, 2 digital outputs can carry signals to the microcontroller, one output to determine direction of shaft rotation and the other output to determine speed of shaft rotation. (if output B changes when output A is high, the shaft is rotating in one direction; if output B changes when output A is low, the shaft is rotating in the other direction).

			[http://thedenneys.org/pub/robot/encoders/ Denneys on optical incremental encoders]

YK: /* Shaft Encoder */ Added second resource for encoder design

2011-06-05T00:16:03Z

Shaft Encoder: Added second resource for encoder design

← Older revision		Revision as of 00:16, 5 June 2011
Line 46:		Line 46:

	[http://translate.google.com/translate?js=y&prev=_t&hl=en&ie=UTF-8&layout=1&eotf=1&u=http://sites.google.com/site/proyectosroboticos/encoder Resource for Incremental Encoder Design]		[http://translate.google.com/translate?js=y&prev=_t&hl=en&ie=UTF-8&layout=1&eotf=1&u=http://sites.google.com/site/proyectosroboticos/encoder Resource for Incremental Encoder Design]

			[http://www.societyofrobots.com/sensors_encoder.shtml Society of Robots on Incremental Encoder Design]

	The current development plan is to use incremental encoders for their low cost, high resolution, and simplicity of design and fabrication relative to absolute encoders.		The current development plan is to use incremental encoders for their low cost, high resolution, and simplicity of design and fabrication relative to absolute encoders.

	Incremental encoders can be split into 2 types: magnetic and optical.		Incremental encoders can be split into 2 types: magnetic and optical.

YK: /* Shaft Encoder */ Added resource and development plan on encoders

2011-06-02T22:50:59Z

Shaft Encoder: Added resource and development plan on encoders

← Older revision		Revision as of 22:50, 2 June 2011
Line 44:		Line 44:

	An absolute encoder can identify different positions of the measured shaft, but is more complex than an incremental encoder. However, an incremental encoder only provides relative position information. An incremental encoder can be used as an "absolute" one by saving the relative movement information; for instance, for day 1, joint A moves 5 degrees clockwise from the home position, then day 2, joint A moves 10 more degrees clockwise; by saving the information from day 1, the microcontroller can understand that joint A has moved a total of 15 degrees clockwise from the home position, not just 10 degrees.		An absolute encoder can identify different positions of the measured shaft, but is more complex than an incremental encoder. However, an incremental encoder only provides relative position information. An incremental encoder can be used as an "absolute" one by saving the relative movement information; for instance, for day 1, joint A moves 5 degrees clockwise from the home position, then day 2, joint A moves 10 more degrees clockwise; by saving the information from day 1, the microcontroller can understand that joint A has moved a total of 15 degrees clockwise from the home position, not just 10 degrees.

			[http://translate.google.com/translate?js=y&prev=_t&hl=en&ie=UTF-8&layout=1&eotf=1&u=http://sites.google.com/site/proyectosroboticos/encoder Resource for Incremental Encoder Design]

			The current development plan is to use incremental encoders for their low cost, high resolution, and simplicity of design and fabrication relative to absolute encoders.

			Incremental encoders can be split into 2 types: magnetic and optical.

YK: Added brief descriptions of components

2011-06-02T02:00:00Z

Added brief descriptions of components

← Older revision		Revision as of 02:00, 2 June 2011
Line 10:		Line 10:

	=Micro-controller=		=Micro-controller=

			The microcontroller is the programmable command unit of the industrial robot. The microcontroller can send signals to the stepper motor drivers and solenoid drivers to move the robot; the microcontroller can receive signals from the shaft encoder to determine how far the robot has moved at each of the 6 joints.

	Possibility is an Arduino microcontroller (such as the Arduino Mega 2560) [http://www.arduino.cc/ Arduino Website]		Possibility is an Arduino microcontroller (such as the Arduino Mega 2560) [http://www.arduino.cc/ Arduino Website]
Line 23:		Line 25:
	=Solenoid Driver=		=Solenoid Driver=

	Possibility is the PWM ~~Solenoid~~ Driver from RepRap wiki [http://reprap.org/wiki/PWM_Driver_1_1?sortcol=0&table=1&up=1 PWM Driver 1.1]		The function of the solenoid driver is to power on and off the solenoid valves. The solenoid driver receives a pulse width modulation signal from the microcontroller and amplifies that signal; the amplified signal is a DC output that energizes the solenoid valve.

			Possibility is the PWM Driver 1.1 from RepRap wiki [http://reprap.org/wiki/PWM_Driver_1_1?sortcol=0&table=1&up=1 PWM Driver 1.1]

	=Stepper Motor Driver=		=Stepper Motor Driver=

	The stepper motor driver to be used ~~is from~~ [[Stepper Motor Controller]]		The function of the stepper motor driver is to power the stepper motors in discrete increments; the stepper motor shaft then rotates based on how much energy was provided by the stepper motor driver.

			More information on stepper motor controllers can be found in the following link; the design contained in that link is the one planned to be used for the industrial robot. [[Stepper Motor Controller]]

	=Shaft Encoder=		=Shaft Encoder=
Line 34:		Line 40:

	[http://en.wikipedia.org/wiki/Rotary_encoder Wikipedia on Rotary Encoders]		[http://en.wikipedia.org/wiki/Rotary_encoder Wikipedia on Rotary Encoders]

			The function of the shaft encoder is to determine the position of a motor shaft as time passes. This function is necessary for the industrial robot to perform tasks with accuracy, because the robot's movement is determined not only by the power supplied to the motors but also the load being moved. For instance, more power is required to lift a boulder than a baseball. It is easier, more practical, and more accurate to have a position sensor (shaft encoder) than having to calculate different power inputs for each load.

	An absolute encoder can identify different positions of the measured shaft, but is more complex than an incremental encoder. However, an incremental encoder only provides relative position information. An incremental encoder can be used as an "absolute" one by saving the relative movement information; for instance, for day 1, joint A moves 5 degrees clockwise from the home position, then day 2, joint A moves 10 more degrees clockwise; by saving the information from day 1, the microcontroller can understand that joint A has moved a total of 15 degrees clockwise from the home position, not just 10 degrees.		An absolute encoder can identify different positions of the measured shaft, but is more complex than an incremental encoder. However, an incremental encoder only provides relative position information. An incremental encoder can be used as an "absolute" one by saving the relative movement information; for instance, for day 1, joint A moves 5 degrees clockwise from the home position, then day 2, joint A moves 10 more degrees clockwise; by saving the information from day 1, the microcontroller can understand that joint A has moved a total of 15 degrees clockwise from the home position, not just 10 degrees.

YK: edited for readability

2011-06-01T23:40:47Z

edited for readability

← Older revision		Revision as of 23:40, 1 June 2011
Line 1:		Line 1:
	=Electrical Design Illustrated Overview=		=Electrical Design Illustrated Overview=

	[[Image:RobotElecOverview.png]]		[[Image:RobotElecOverview.png\|790px]]

	=Toolchain for Toolpaths=		=Toolchain for Toolpaths=