Ironworker/Manufacturing Instructions - Revision history

Marcin: /* Prototype II Blade */

2012-12-04T16:35:12Z

Prototype II Blade

2012-12-04T16:34:59Z

Prototype II Blade

2012-12-04T16:34:28Z

Introduction

2012-01-17T06:13:58Z

Introduction

← Older revision		Revision as of 06:13, 17 January 2012
Line 8:		Line 8:
	<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=76574afca0dc2a81211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html><br/>		<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=76574afca0dc2a81211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html><br/>

	Note: Prototype 1 Capacity is actually 45 Tons, because the main arm was too thin to withstand warping from pressure. The holes egged from punching holes above this rated capacity. If this arm, and the linkage attaching it to the punch were 1.5" thick, the capacity would jump to 60 tons.		Note: Prototype 1 Capacity is actually 45 Tons, because the main arm was too thin to withstand warping from pressure. The holes for the main pin, and linkage pins egged from punching holes above this rated capacity. If this arm, and the linkage attaching it to the punch were 1.5" thick, the capacity would jump to 60 tons.

	==Build==		==Build==

2012-01-17T06:13:14Z

Introduction

← Older revision		Revision as of 06:13, 17 January 2012
Line 6:		Line 6:

	Sketchup of prototype 1:<br/>		Sketchup of prototype 1:<br/>
	<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=76574afca0dc2a81211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>		<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=76574afca0dc2a81211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html><br/>

			Note: Prototype 1 Capacity is actually 45 Tons, because the main arm was too thin to withstand warping from pressure. The holes egged from punching holes above this rated capacity. If this arm, and the linkage attaching it to the punch were 1.5" thick, the capacity would jump to 60 tons.

	==Build==		==Build==

2012-01-13T04:23:48Z

Introduction

← Older revision		Revision as of 04:23, 13 January 2012
Line 4:		Line 4:

	See [[Ironworkers]] for introduction.		See [[Ironworkers]] for introduction.

			Sketchup of prototype 1:<br/>
			<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=76574afca0dc2a81211da1f85706ccd&etyp=sw&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>

	==Build==		==Build==

2011-09-06T01:01:45Z

← Older revision		Revision as of 01:01, 6 September 2011
Line 1:		Line 1:
	{{~~ToolTemplate\|ToolName=Ironworker~~}}		{{GVCS Header}}

	==Introduction==		==Introduction==
Line 39:		Line 39:

	[[Category:Ironworker]][[Category:Hole Puncher]][[Category:RepLab]]		[[Category:Ironworker]][[Category:Hole Puncher]][[Category:RepLab]]

			{{GVCS Footer}}

2011-08-23T03:20:45Z

← Older revision		Revision as of 03:20, 23 August 2011
Line 1:		Line 1:
	=Introduction=		{{ToolTemplate\|ToolName=Ironworker}}

			==Introduction==

	See [[Ironworkers]] for introduction.		See [[Ironworkers]] for introduction.

	=Build=		==Build==
	We start the build of the ''open source ironworker'' with a 120 ton hole puncher for poking up to 1.5 inch holes in 1" steel (figure based on Edwards ironworkers) plate.		We start the build of the ''open source ironworker'' with a 120 ton hole puncher for poking up to 1.5 inch holes in 1" steel (figure based on Edwards ironworkers) plate.

Line 12:		Line 14:
	You can download the file [http://openpario.mime.oregonstate.edu:3000/documents/96 here.]		You can download the file [http://openpario.mime.oregonstate.edu:3000/documents/96 here.]

	=Design v0.1=		==Design v0.1==

	[[Image:holepuncher01.jpg]]		[[Image:holepuncher01.jpg]]

	=Bill of Materials=		==Bill of Materials==
	*5"x8" hydrauilic cylinder		*5"x8" hydrauilic cylinder
	*[2]1"x4" pin - for mounting cylinder		*[2]1"x4" pin - for mounting cylinder

2011-08-23T03:19:48Z

← Older revision	Revision as of 03:19, 23 August 2011
(No difference)

2010-06-26T05:05:38Z

Bill of Materials

@@ Line 21: / Line 21: @@
 *[2]3/4" or 1" washers
 *[2] 1"x10"x48" plate - main parallel pieces
+*
 [[Category:Ironworker]][[Category:Hole Puncher]][[Category:RepLab]]