Lathe Specifications - Revision history

Dennis at 09:13, 17 March 2009

2009-03-17T09:13:46Z

← Older revision		Revision as of 09:13, 17 March 2009
Line 1:		Line 1:
	~~'''~~Fabrication and Cost~~'''~~		==Fabrication and Cost==
	*Ease and low cost of fabrication is the primary goal, as a high-performance lathe is perhaps the most important tool in a workshop		*Ease and low cost of fabrication is the primary goal, as a high-performance lathe is perhaps the most important tool in a workshop
	*Construction consists of a concrete bed		*Construction consists of a concrete bed
Line 14:		Line 14:
	[[Image:Lathe.jpg]]		[[Image:Lathe.jpg]]

	~~'''~~Specifications~~'''~~		==Specifications==
	*12" lathe		*12" lathe
	*1/1000" accuracy via bearing tolerance and chuck tolerance		*1/1000" accuracy via bearing tolerance and chuck tolerance

Jeremy at 22:17, 5 March 2009

2009-03-05T22:17:28Z

← Older revision		Revision as of 22:17, 5 March 2009
Line 19:		Line 19:
	*Heavy duty axial thrust acceptable, as determined by 3" shaft and bearings		*Heavy duty axial thrust acceptable, as determined by 3" shaft and bearings
	*Radial thrust determined by set screws on 2 bearings, with 2 extra full split collars		*Radial thrust determined by set screws on 2 bearings, with 2 extra full split collars


			=BOM=
			*http://www.thebigbearingstore.com/servlet/the-57/2%22-Pillow-Block-Bearing/Detail
			*


	[[Category:Specifications]]		[[Category:Specifications]]

WikiSysop at 04:39, 2 March 2009

2009-03-02T04:39:50Z

← Older revision		Revision as of 04:39, 2 March 2009
Line 10:		Line 10:
	*2" shaft constitutes a mounting surface for an xy table and for tail stock		*2" shaft constitutes a mounting surface for an xy table and for tail stock
	*Feed-through shaft is present, but is only 1 foot deep		*Feed-through shaft is present, but is only 1 foot deep
			*[http://surpluscenter.com/item.asp?UID=2009030121420114&item=1-215-47-4-S&catname=powerTrans Cheap 2 15/16" bearing]

	[[Image:Lathe.jpg]]		[[Image:Lathe.jpg]]

WikiSysop at 04:37, 2 March 2009

2009-03-02T04:37:23Z

← Older revision		Revision as of 04:37, 2 March 2009
Line 12:		Line 12:

	[[Image:Lathe.jpg]]		[[Image:Lathe.jpg]]

			'''Specifications'''
			*12" lathe
			*1/1000" accuracy via bearing tolerance and chuck tolerance
			*Heavy duty axial thrust acceptable, as determined by 3" shaft and bearings
			*Radial thrust determined by set screws on 2 bearings, with 2 extra full split collars

			[[Category:Specifications]]

WikiSysop at 04:27, 2 March 2009

2009-03-02T04:27:56Z

← Older revision		Revision as of 04:27, 2 March 2009
Line 10:		Line 10:
	*2" shaft constitutes a mounting surface for an xy table and for tail stock		*2" shaft constitutes a mounting surface for an xy table and for tail stock
	*Feed-through shaft is present, but is only 1 foot deep		*Feed-through shaft is present, but is only 1 foot deep

			[[Image:Lathe.jpg]]

WikiSysop: New page: '''Fabrication and Cost''' Ease and low cost of fabrication is the primary goal, as a high-performance lathe is perhaps the most important tool in a workshop Construction consists of a c...

2009-03-02T04:20:29Z

New page: '''Fabrication and Cost''' *Ease and low cost of fabrication is the primary goal, as a high-performance lathe is perhaps the most important tool in a workshop *Construction consists of a c...

New page

'''Fabrication and Cost'''
*Ease and low cost of fabrication is the primary goal, as a high-performance lathe is perhaps the most important tool in a workshop
*Construction consists of a concrete bed
*Cost is that of 4 bags of concrete for the bed, chuck, cross slide, and
*Motor cost is included in [[LifeTrac]] infrastructure
*Motor coupler to lathe shaft is machined
*Commercial chck is the main cost
*XY table constitutes a cross slide
*Tool post is fabricated
*2" shaft constitutes a mounting surface for an xy table and for tail stock
*Feed-through shaft is present, but is only 1 foot deep