LifeTrac IV/Manufacturing Instructions/Frame - Revision history

Dorkmo: /* Torch */

2012-03-20T04:04:55Z

Torch

← Older revision		Revision as of 04:04, 20 March 2012
Line 52:		Line 52:
	holes for arm shaft		holes for arm shaft
	22" from back of front-to-back top frame tube		22" from back of front-to-back top frame tube
			:Diameter depends on outside diameter of pipe for holding the arm shaft

Dorkmo: /* Torch */

2012-03-19T21:43:06Z

Torch

← Older revision		Revision as of 21:43, 19 March 2012
Line 51:		Line 51:
	===Torch===		===Torch===
	holes for arm shaft		holes for arm shaft
			22" from back of front-to-back top frame tube

Dorkmo at 20:28, 19 March 2012

2012-03-19T20:28:08Z

← Older revision		Revision as of 20:28, 19 March 2012
Line 48:		Line 48:
	: Drill holes at 6", 38"		: Drill holes at 6", 38"
	: Rotate 90 degrees, drill holes at 2", 42"		: Rotate 90 degrees, drill holes at 2", 42"

			===Torch===
			holes for arm shaft

Dorkmo: Created page with "===cut=== 4"X4"X1/4" Square Tubing Four 76" Two 68" Three 60" Two 59" Two 55" Two 52" Three 44" ===drill=== Unless otherwise specified, drill all holes at 13/16" diame..."

2012-03-19T20:26:46Z

Created page with "===cut=== 4"X4"X1/4" Square Tubing *Four 76" *Two 68" *Three 60" *Two 59" *Two 55" *Two 52" *Three 44" ===drill=== * Unless otherwise specified, drill all holes at 13/16" diame..."

New page

===cut===
4"X4"X1/4" Square Tubing
*Four 76"
*Two 68"
*Three 60"
*Two 59"
*Two 55"
*Two 52"
*Three 44"

===drill===

* Unless otherwise specified, drill all holes at 13/16" diameter.
* Drill holes through entire tube (ie: through both sides).
* For each tube, measure all holes from one end of tube.

----

; 3 Lower cross tubes, 60" long
: Drill holes at 14", 46"
: Rotate 90 degrees, drill holes at 2", 10", 50", 58"

; 2 Bottom Inner North-South tubes, 76" long
: Drill holes at 6", ? 70"
: Rotate 90 degrees, drill holes at 2", ? 50", 58"

; 2 Bottom Outer North-South tubes, 76" long
: Drill holes at ?
: Rotate 90 degrees, drill holes at 2", ? 74"

; 2 Front Vertical tubes, 55" long
: Drill holes at 6", 50"
: Rotate 90 degrees, drill holes at 2", 46"

; 2 Middle Vertical tubes, 52" long
: Drill holes at 6", 24", 50"
: Rotate 90 degrees, drill holes at 2", 46"

; 2 Rear Vertical tubes, 59" long
: Drill holes at 2", 21", 29 1/2", 47 1/2", 54"
: Rotate 90 degrees, drill holes at 6", 50"

; 2 Top North-South tubes, 68" long
: Drill holes at 6", 22", 62"
: Rotate 90 degrees, drill holes at 2", 26", 66" and a 2 3/8" hole @ 48" (with cutting torch)

; 3 Top Cross tubes, 44" long
: Drill holes at 6", 38"
: Rotate 90 degrees, drill holes at 2", 42"

LifeTrac IV/Manufacturing Instructions/Frame - Revision history

Dorkmo: /* Torch */

Dorkmo: /* Torch */

Dorkmo at 20:28, 19 March 2012

Dorkmo: Created page with "===cut=== 4"X4"X1/4" Square Tubing *Four 76" *Two 68" *Three 60" *Two 59" *Two 55" *Two 52" *Three 44" ===drill=== * Unless otherwise specified, drill all holes at 13/16" diame..."

Dorkmo: Created page with "===cut=== 4"X4"X1/4" Square Tubing Four 76" Two 68" Three 60" Two 59" Two 55" Two 52" Three 44" ===drill=== Unless otherwise specified, drill all holes at 13/16" diame..."