Master Interface Process - Revision history

Marcin at 20:49, 18 June 2022

2022-06-18T20:49:40Z

← Older revision		Revision as of 20:49, 18 June 2022
Line 1:		Line 1:
	OSE's method for adding [[BIM]] house layers. A layer is defined by drawing a contour at the right height within FreeCAD. For [[Seed Eco-Home]], the design works around the bottom edge of beadboard for house circuit design. See working doc [https://docs.google.com/presentation/d/1ryuVJO_YEAID97JgGmrzYeAFA_RrwwyLfWe0NdrobNc/edit#slide=id.g133e72099cc_0_70].		OSE's method for adding [[BIM]] house layers. A layer is defined by drawing a contour at the right height within FreeCAD. For [[Seed Eco-Home]], the design works around the bottom edge of beadboard for house circuit design. See working doc [https://docs.google.com/presentation/d/1ryuVJO_YEAID97JgGmrzYeAFA_RrwwyLfWe0NdrobNc/edit#slide=id.g133e72099cc_0_70].

	For example, where do you design your electrical boxes? If you know the wall layout design, and you know that the electrical boxes are flush with the interior skin (beadboard) - and you know the height of the bottom of the electrical box - then you have defined where an electrical box goes on any ~~give~~ interior or exterior wall module.		For example, where do you design your electrical boxes? If you know the wall layout design, and you know that the electrical boxes are flush with the interior skin (beadboard) - and you know the height of the bottom of the electrical box - then you have defined where an electrical box goes on any given interior or exterior wall module.

Marcin at 20:42, 18 June 2022

2022-06-18T20:42:36Z

← Older revision		Revision as of 20:42, 18 June 2022
Line 1:		Line 1:
	OSE's method for adding BIM house layers. A layer is defined by drawing a contour at the right height. For [[Seed Eco-Home]], the design works around the bottom edge of beadboard for house circuit design. See working doc [https://docs.google.com/presentation/d/1ryuVJO_YEAID97JgGmrzYeAFA_RrwwyLfWe0NdrobNc/edit#slide=id.g133e72099cc_0_70].		OSE's method for adding [[BIM]] house layers. A layer is defined by drawing a contour at the right height within FreeCAD. For [[Seed Eco-Home]], the design works around the bottom edge of beadboard for house circuit design. See working doc [https://docs.google.com/presentation/d/1ryuVJO_YEAID97JgGmrzYeAFA_RrwwyLfWe0NdrobNc/edit#slide=id.g133e72099cc_0_70].

			For example, where do you design your electrical boxes? If you know the wall layout design, and you know that the electrical boxes are flush with the interior skin (beadboard) - and you know the height of the bottom of the electrical box - then you have defined where an electrical box goes on any give interior or exterior wall module.

Marcin: Created page with "OSE's method for adding BIM house layers. A layer is defined by drawing a contour at the right height. For Seed Eco-Home, the design works around the bottom edge of beadbo..."

2022-06-18T20:40:25Z

Created page with "OSE's method for adding BIM house layers. A layer is defined by drawing a contour at the right height. For Seed Eco-Home, the design works around the bottom edge of beadbo..."

New page

OSE's method for adding BIM house layers. A layer is defined by drawing a contour at the right height. For [[Seed Eco-Home]], the design works around the bottom edge of beadboard for house circuit design. See working doc [https://docs.google.com/presentation/d/1ryuVJO_YEAID97JgGmrzYeAFA_RrwwyLfWe0NdrobNc/edit#slide=id.g133e72099cc_0_70].