Mount Cylinders - Revision history

Marcin at 04:48, 19 June 2011

2011-06-19T04:48:15Z

← Older revision		Revision as of 04:48, 19 June 2011
Line 1:		Line 1:
	Start with bottom cylinder mount assembly:		'''Start with bottom cylinder mount assembly:'''
	*[1] Cut 1/2"X6"x12" plate		*[1] Cut 1/2"X6"x12" plate
	*[2] Cut 1/2"x4"x6" plate		*[2] Cut 1/2"x4"x6" plate
Line 8:		Line 8:
	*Weld assembly together with cylinder pin in place (prevents shifting)		*Weld assembly together with cylinder pin in place (prevents shifting)

	Move to top of main cylinder, which is also the mount for the secondary cylinder – call this the common cylinder mount.		'''Move to top of main cylinder, which is also the mount for the secondary cylinder – call this the common cylinder mount.
			'''
	*[2] Cut 6”x12” plate		*[2] Cut 6”x12” plate
	*Declare 4 hole locations for mounting to arms		*Declare 4 hole locations for mounting to arms
Line 19:		Line 19:
	*Attach main cylinder (mounted only at top) and secondary cylinder (mounted only at bottom) to common cylinder mount		*Attach main cylinder (mounted only at top) and secondary cylinder (mounted only at bottom) to common cylinder mount

	With common cylinder mounting attached to cylinders, work the second attachment points of both cylinders		'''With common cylinder mounting attached to cylinders, work the second attachment points of both cylinders.'''

	*Attach bottom cylinder mount to main cylinder with pins		*Attach bottom cylinder mount to main cylinder with pins
Line 27:		Line 27:
	*Mark locations on opposite side and drill with 13/16” annular cutter		*Mark locations on opposite side and drill with 13/16” annular cutter
	*Pin top of secondary cylinder to the QA Plate mounts		*Pin top of secondary cylinder to the QA Plate mounts



	[[Category:Fabrication Procedures]]		[[Category:Fabrication Procedures]]


	*Drill cylinder mount plate holes in loader arms
	*Mount cylinder plates (2 per arm)
	*With loader arms in place, arrange bottom and top mounts, drill holes
	*Attach main cylinder to arms
	*With main cylinder attached, finetune location of bottom cylinder mount for equal extension of cylinders
	*Drill bottom mount locations
	*Bolt bottom mounts

Marcin at 04:30, 19 June 2011

2011-06-19T04:30:56Z

← Older revision		Revision as of 04:30, 19 June 2011
Line 8:		Line 8:
	*Weld assembly together with cylinder pin in place (prevents shifting)		*Weld assembly together with cylinder pin in place (prevents shifting)

	Move to top of main cylinder, which is also the mount for the secondary cylinder		Move to top of main cylinder, which is also the mount for the secondary cylinder – call this the common cylinder mount.

	*[2] Cut 6”x12” plate		*[2] Cut 6”x12” plate
Line 14:		Line 14:
	*Drill plates a pair at one time, clamped together – [4] ¾” holes and [2] 1” holes		*Drill plates a pair at one time, clamped together – [4] ¾” holes and [2] 1” holes
	*Align these plates by inserting the pins into these and clamping to arms prior to transfer punching holes		*Align these plates by inserting the pins into these and clamping to arms prior to transfer punching holes
	*Transfer punch hole locations to arms ~~from~~ both sides		*Transfer punch hole locations to arms on both sides
	*Drill 4 holes for loader arm attachment per each side, one side at a time		*Drill 4 holes for loader arm attachment per each side, one side at a time
	*~~Drilland 2 for pins - per each plate~~		*Bolt common cylinder mount to arms
	*Attach main cylinder and secondary cylinder		*Attach main cylinder (mounted only at top) and secondary cylinder (mounted only at bottom) to common cylinder mount
	*~~Lay assembly in place on frame, and pin~~ bottom of main cylinder ~~into it~~
	*~~Pin top~~ of main cylinder ~~into the arm attachment plates~~		With common cylinder mounting attached to cylinders, work the second attachment points of both cylinders
	*~~Pin~~ bottom ~~of secondary~~ cylinder ~~to the arm attachment plates~~
			*Attach bottom cylinder mount to main cylinder with pins
			*Fix the location of the bottom mount of the main cylinder (on each side of tractor) such that the loader arms are fully down in the retracted cylinder position.
			*Transfer punch locations of main cylinder bottom bolt holes
			*Drill bottom cylinder mounts with annular cutter mag drill - 3/4”
			*Mark locations on opposite side and drill with 13/16” annular cutter
	*Pin top of secondary cylinder to the QA Plate mounts		*Pin top of secondary cylinder to the QA Plate mounts

Marcin at 04:09, 19 June 2011

2011-06-19T04:09:50Z

← Older revision		Revision as of 04:09, 19 June 2011
Line 1:		Line 1:
	Start with bottom cylinder.		Start with bottom cylinder mount assembly:
	*[1] Cut 1/2"X6"x12" plate		*[1] Cut 1/2"X6"x12" plate
	*[2] Cut 1/2"x4"x6" plate		*[2] Cut 1/2"x4"x6" plate
	*Mag drill or punch [4] 3/4" holes in 6"x12" plate		*Mag drill or punch [4] 3/4" holes in 6"x12" plate for attachment of main cylinder to frame
	*Mag drill or punch [2] 1" pin holes on each 4"x6" plate		*Mag drill or punch [2] 1" pin holes on each 4"x6" plate for attachment of main cylinder
	*Weld 1" drilled out nut onto 4"x6" plates		*Weld a reinforcing gusset nut - 1" drilled out nut onto 4"x6" plates
	*Tack [2] plates about 3.5" apart for cylinder mounting		*Tack [2] plates about 3.5" apart for cylinder mounting
	*Weld assembly together with cylinder pin in place (prevents shifting)		*Weld assembly together with cylinder pin in place (prevents shifting)

			Move to top of main cylinder, which is also the mount for the secondary cylinder

			*[2] Cut 6”x12” plate
			*Declare 4 hole locations for mounting to arms
			*Drill plates a pair at one time, clamped together – [4] ¾” holes and [2] 1” holes
			*Align these plates by inserting the pins into these and clamping to arms prior to transfer punching holes
			*Transfer punch hole locations to arms from both sides
			*Drill 4 holes for loader arm attachment per each side, one side at a time
			*Drilland 2 for pins - per each plate
			*Attach main cylinder and secondary cylinder
	*Lay assembly in place on frame, and pin bottom of main cylinder into it		*Lay assembly in place on frame, and pin bottom of main cylinder into it
	*Pin top of main cylinder into the arm attachment plates		*Pin top of main cylinder into the arm attachment plates
Line 24:		Line 35:
	*Drill bottom mount locations		*Drill bottom mount locations
	*Bolt bottom mounts		*Bolt bottom mounts

	~~[[Category:Production Plan]]~~

Marcin at 03:54, 19 June 2011

2011-06-19T03:54:18Z

← Older revision		Revision as of 03:54, 19 June 2011
Line 1:		Line 1:
			Start with bottom cylinder.
	*[1] Cut 1/2"X6"x12" plate		*[1] Cut 1/2"X6"x12" plate
	*[2] Cut 1/2"x4"x6" plate		*[2] Cut 1/2"x4"x6" plate
	*Mag drill or punch [4] 3/4" holes in 6"x12: plate		*Mag drill or punch [4] 3/4" holes in 6"x12" plate
	*Mag drill or punch [2] 1" pin holes on each 4"x6" plate		*Mag drill or punch [2] 1" pin holes on each 4"x6" plate
	*Weld 1" drilled out nut onto 4"x6" plates		*Weld 1" drilled out nut onto 4"x6" plates

Marcin at 01:41, 19 June 2011

2011-06-19T01:41:14Z

← Older revision		Revision as of 01:41, 19 June 2011
Line 1:		Line 1:
			*[1] Cut 1/2"X6"x12" plate
			*[2] Cut 1/2"x4"x6" plate
			*Mag drill or punch [4] 3/4" holes in 6"x12: plate
			*Mag drill or punch [2] 1" pin holes on each 4"x6" plate
			*Weld 1" drilled out nut onto 4"x6" plates
			*Tack [2] plates about 3.5" apart for cylinder mounting
			*Weld assembly together with cylinder pin in place (prevents shifting)
			*Lay assembly in place on frame, and pin bottom of main cylinder into it
			*Pin top of main cylinder into the arm attachment plates
			*Pin bottom of secondary cylinder to the arm attachment plates
			*Pin top of secondary cylinder to the QA Plate mounts



			[[Category:Fabrication Procedures]]


	*Drill cylinder mount plate holes in loader arms		*Drill cylinder mount plate holes in loader arms
	*Mount cylinder plates (2 per arm)		*Mount cylinder plates (2 per arm)

Marcin: Created page with "Drill cylinder mount plate holes in loader arms Mount cylinder plates (2 per arm) With loader arms in place, arrange bottom and top mounts, drill holes Attach main cylinder t..."

2011-06-19T01:13:22Z

Created page with "*Drill cylinder mount plate holes in loader arms *Mount cylinder plates (2 per arm) *With loader arms in place, arrange bottom and top mounts, drill holes *Attach main cylinder t..."

New page

*Drill cylinder mount plate holes in loader arms
*Mount cylinder plates (2 per arm)
*With loader arms in place, arrange bottom and top mounts, drill holes
*Attach main cylinder to arms
*With main cylinder attached, finetune location of bottom cylinder mount for equal extension of cylinders
*Drill bottom mount locations
*Bolt bottom mounts

[[Category:Production Plan]]