Multimachine Development - Revision history

Shonda at 17:27, 18 July 2011

2011-07-18T17:27:49Z

← Older revision		Revision as of 17:27, 18 July 2011
Line 19:		Line 19:

	*CAD model machine frame (concrete)		*CAD model machine frame (concrete)
	*test of epoxy resin alignment methods (jig to hold part 40 thou (1mm) above bonding surface and then epoxy ~~rein~~ in place)		*test of epoxy resin alignment methods (jig to hold part 40 thou (1mm) above bonding surface and then epoxy resin in place)
	* working on redesigning to use a precast concrete base that will have components mounted onto it.		* working on redesigning to use a precast concrete base that will have components mounted onto it.

			=Joining the Multimachine Project=

			If you want to work on the Multimachine project please have filled out a [[Team Culturing Survey]] and leave a paragraph and your name below. Currently areas of expertise that we need are, concrete base/reinforcement, hydraulic system, statics, and general mechanical design.

	=Funding Situation=		=Funding Situation=

Shonda at 17:40, 8 July 2011

2011-07-08T17:40:01Z

← Older revision		Revision as of 17:40, 8 July 2011
Line 7:		Line 7:
	07/07/11 : worked on organizing wiki information so that information doesn't get lost and is readily available.		07/07/11 : worked on organizing wiki information so that information doesn't get lost and is readily available.

	Spindle designs are done for the most part, bearings should be adequate at P5 specification and will run ~~4000~~ rpm with ~~grease lubricant or 6000 with oil~~		Spindle designs are done for the most part, bearings should be adequate at P5 specification and will run 56000 rpm normally with a maximum limit of 7000 RPM.

	=Unanswered Questions=		=Unanswered Questions=

	*source for Resin Epoxy		*source for Resin Epoxy (less important with concrete frame)
			*methods for a concrete cast base
			*will epoxy resin between concrete and steel surface be strong enough to support the milling table


	=current tasks=		=current tasks=

	*CAD model machine frame		*CAD model machine frame (concrete)
	*test ~~molding~~ of ~~Epoxy/Granite~~		*test of epoxy resin alignment methods (jig to hold part 40 thou (1mm) above bonding surface and then epoxy rein in place)
			* working on redesigning to use a precast concrete base that will have components mounted onto it.

	=Funding Situation=		=Funding Situation=
Line 25:		Line 29:

	* probably 2 weeks to a month of design time, if its only me, before I have a finished design to build.		* probably 2 weeks to a month of design time, if its only me, before I have a finished design to build.



	[[Category:Multimachine]]		[[Category:Multimachine]]

Shonda at 01:30, 8 July 2011

2011-07-08T01:30:50Z

← Older revision		Revision as of 01:30, 8 July 2011
Line 5:		Line 5:
	=Progress Report=		=Progress Report=

	07/07/11 : worked on organizing wiki information so that information doesn't get lost and is readily available. ~~spindle~~ designs are done for the most part, bearings should be adequate at P5 specification and will run 4000 rpm with grease lubricant or 6000 with oil		07/07/11 : worked on organizing wiki information so that information doesn't get lost and is readily available.

			Spindle designs are done for the most part, bearings should be adequate at P5 specification and will run 4000 rpm with grease lubricant or 6000 with oil

	=Unanswered Questions=		=Unanswered Questions=

Shonda: Created page with "{{Category=Drill-mill-lathe}} {{ToolTemplate|ToolName=Multimachine}} =Progress Report= 07/07/11 : worked on organizing wiki information so that information doesn't get lost an..."

2011-07-08T01:29:53Z

Created page with "{{Category=Drill-mill-lathe}} {{ToolTemplate|ToolName=Multimachine}} =Progress Report= 07/07/11 : worked on organizing wiki information so that information doesn't get lost an..."

New page

{{Category=Drill-mill-lathe}}

{{ToolTemplate|ToolName=Multimachine}}

=Progress Report=

07/07/11 : worked on organizing wiki information so that information doesn't get lost and is readily available. spindle designs are done for the most part, bearings should be adequate at P5 specification and will run 4000 rpm with grease lubricant or 6000 with oil

=Unanswered Questions=

*source for Resin Epoxy

=current tasks=

*CAD model machine frame
*test molding of Epoxy/Granite

=Funding Situation=

07/07/11 : Dunwoody College of Technology has expressed interest in funding a first prototype, they would pay for materials and costume tooling, but would own the first model when completed. I (Shonda) believe its a good idea if money, rather then time, is an issue because a lot of the kinks of the design can be worked out in the first prototype and the second machine will be that much faster and slightly cheaper to produce.

=Timeline=

* probably 2 weeks to a month of design time, if its only me, before I have a finished design to build.

[[Category:Multimachine]]