Multimachine Intro - Revision history

Shonda: /* Specifications */

2011-07-18T17:18:15Z

Specifications

← Older revision		Revision as of 17:18, 18 July 2011
Line 51:		Line 51:
	=Specifications=		=Specifications=

	*hybrid ~~weldment~~/~~Epoxy-~~concrete cast bases		*hybrid rebar/concrete cast bases (later work to be done on epoxy/granite bases)
	*spindle with < .001in (25 microns) of runout		*spindle with < .001in (25 microns) of runout (shuck will increase runout but .01 at spindle nose should be doable)
	*spindle speed > 6000RPM		*max spindle speed > 6000RPM
	*table true to within .001 on length		*table true to within .001 (25 microns) on length
	*modular liner rails from 6" - 50" (300mm - 1.25m) travel or more		*modular liner rails from 6" - 50" (300mm - 1.25m) travel or more
	*modular rails and spindle fit to bed with replication material sealant		*modular rails and spindle fit to bed with replication material sealant
	*overarm for mounting arbors		*overarm for mounting arbors and vertical heads
	*attachment points for bolting on a vertical ~~milling head~~

	=Links=		=Links=

2011-07-14T17:04:56Z

← Older revision		Revision as of 17:04, 14 July 2011
Line 2:		Line 2:

	{{ToolTemplate\|ToolName=Multimachine}}		{{ToolTemplate\|ToolName=Multimachine}}

			[[File:ConcreteRough.JPG\|right\|thumb\|current model, still a lot of work to do (this one was eyeballed). no drive for any of the tables yet but I'll(Shonda) have it in a couple days.]]

	=Project Description=		=Project Description=

2011-07-08T03:42:24Z

Cost

← Older revision		Revision as of 03:42, 8 July 2011
Line 44:		Line 44:
	*seals $10 each X2		*seals $10 each X2
	*preload nuts 45mm X2		*preload nuts 45mm X2

			compared to a fully outfitted Bridgeport vertical mill at $30,000 (with DROs, tool changer and power feeds)

	=Specifications=		=Specifications=

2011-07-08T03:36:47Z

Cost

← Older revision		Revision as of 03:36, 8 July 2011
Line 39:		Line 39:
	=Cost=		=Cost=
	spindle $300		spindle $300
	*spindle bearings 33011/Q ~~50mm~~ by 90mm 80$ each X2		*spindle bearings 33011/Q 55mm by 90mm by 27mm 80$ each X2
	*pipe housing and spindle $30 each X2		*pipe housing and spindle $30 each X2
	*round bar 4.25" ~$50		*round bar 4.25" ~$50
	*seals $10 each X2		*seals $10 each X2
	*preload nuts 45mm X2		*preload nuts 45mm X2


	=Specifications=		=Specifications=

2011-07-08T01:03:41Z

@@ Line 12: / Line 12: @@
 *belt sanding
 *cutoff saw
 = Project Team =
@@ Line 46: / Line 37: @@
 spindle is a counter bored pipe with bearings and seals pressed in. The pipe housing is then mounted in the machine frame and made vertical to the world.  long dovetail ways are aligned perpendicularly to the spindle and parallel to each other.  once alignment is complete epoxy/granite is then mixed and applied to the frame increasing rigidity and weight.  Opposing slide for the embedded dovetail is then assembled onto the embedded dovetail (slide | gibb | embedded slide | space | embedded slide| slide) cast in place.
-spindle bearings 33011/Q  50mm by 90mm
+=Cost=
 =Links=

2011-07-07T18:57:48Z

@@ Line 5: / Line 5: @@
 =Project Description=
 =Design Concept=
 =Links=
 [[Category:Multimachine]]

2011-06-02T13:13:41Z

← Older revision		Revision as of 13:13, 2 June 2011
Line 1:		Line 1:
	{{Category=~~Multimachine~~}}		{{Category=Drill-mill-lathe}}

	{{ToolTemplate\|ToolName=Multimachine}}		{{ToolTemplate\|ToolName=Multimachine}}

2011-06-02T13:13:17Z

← Older revision		Revision as of 13:13, 2 June 2011
Line 1:		Line 1:
	{{Category=~~Drill-mill-lathe~~}}		{{Category=Multimachine}}

	{{ToolTemplate\|ToolName=Multimachine}}		{{ToolTemplate\|ToolName=Multimachine}}
Line 12:		Line 12:


	[[Category:~~Drill-mill-lathe~~]]		[[Category:Multimachine]]

2011-06-02T12:42:27Z

← Older revision		Revision as of 12:42, 2 June 2011
Line 1:		Line 1:
			{{Category=Drill-mill-lathe}}

	{{ToolTemplate\|ToolName=Multimachine}}		{{ToolTemplate\|ToolName=Multimachine}}

Line 10:		Line 12:


	[[Category:~~Metalworking~~]]		[[Category:Drill-mill-lathe]]

2011-06-02T12:41:37Z

← Older revision		Revision as of 12:41, 2 June 2011
Line 1:		Line 1:
			{{ToolTemplate\|ToolName=Multimachine}}

			=Project Description=


			=Design Concept=


			=Links=

	~~{{ToolTemplate\|ToolName=Multimachine}}~~

	~~(stuff goes here)~~		[[Category:Metalworking]]