Nview:3D Printer/Workshop::Accessibility Improvements - Revision history

Alexau: /* Sat Oct 27, 2018 Oakland 1-day Build */

2018-10-29T21:35:56Z

Sat Oct 27, 2018 Oakland 1-day Build

← Older revision		Revision as of 21:35, 29 October 2018
Line 80:		Line 80:
	# Need an identification survey: what type of xp are they coming with?		# Need an identification survey: what type of xp are they coming with?
	# Need an exit survey.		# Need an exit survey.
	# Reduce the number of questions on a per-build phase. Have this be a verbal check-in. And input it on their behalf.		# Reduce the number of questions on a per-build phase. Have this be a verbal check-in. And input it on their behalf. OR have a dedicated ipad where they can click and be done with it. 2 questions tops. supported & confidence.
	# Switch to having a more in-depth module-based survey.		# Switch to having a more in-depth module-based survey.
	# Add an "Newbie Intervention" motivation convo. Folks paralyzed by "I don't know what I don't know" -- need to explicitly dispel this myth. If you can explain it, then you know it. There's not "more to it" ... those are different skills.		# Add an "Newbie Intervention" motivation convo. Folks paralyzed by "I don't know what I don't know" -- need to explicitly dispel this myth. If you can explain it, then you know it. There's not "more to it" ... those are different skills.

2018-10-29T21:32:10Z

Accessbility Improvement Recommendations

← Older revision		Revision as of 21:32, 29 October 2018
Line 87:		Line 87:
	# add Build Phases for the Extruder, especially QC to prevent issues like in this build.		# add Build Phases for the Extruder, especially QC to prevent issues like in this build.
	# add a "time it" component to the workflow		# add a "time it" component to the workflow
	# Have "pre-work" when folks register. Then, start the build right away. For walk-ins, let them watch on their own time and join build afterwards.		# Have "pre-work" when folks register (explaining the modules at a high-level, showing how to drill, solder, participate in our workshop). Then, start the build right away. For walk-ins, let them watch on their own time and join build afterwards.

	==Observations==		==Observations==

2018-10-29T21:30:35Z

Sat Oct 27, 2018 Oakland 1-day Build

← Older revision		Revision as of 21:30, 29 October 2018
Line 87:		Line 87:
	# add Build Phases for the Extruder, especially QC to prevent issues like in this build.		# add Build Phases for the Extruder, especially QC to prevent issues like in this build.
	# add a "time it" component to the workflow		# add a "time it" component to the workflow
			# Have "pre-work" when folks register. Then, start the build right away. For walk-ins, let them watch on their own time and join build afterwards.

	==Observations==		==Observations==

2018-10-29T21:29:46Z

Cable Chain + Final Touches

← Older revision		Revision as of 21:29, 29 October 2018
Line 69:		Line 69:

	=== Cable Chain + Final Touches ===		=== Cable Chain + Final Touches ===
	* Not done. Should set expectations here.		* Not done. Should set expectations here that their homework is to take it apart and put it back together again and use their judgment to tape things to places.

	=== Cleanup ===		=== Cleanup ===

2018-10-29T21:29:19Z

Assembly & First Print

← Older revision		Revision as of 21:29, 29 October 2018
Line 65:		Line 65:
	* Time spent:		* Time spent:
	* Note: x & y axis movement looked good.		* Note: x & y axis movement looked good.
			* Needs build phases and quality control points.
			* Needs "Baby Steps" procedure.

	=== Cable Chain + Final Touches ===		=== Cable Chain + Final Touches ===

2018-10-29T21:28:46Z

Control Panel

← Older revision		Revision as of 21:28, 29 October 2018
Line 59:		Line 59:
	* Note: had to re-pin the motor cables. On the plus side, they were long enough. Not sure if some wires needed to be extended or not.		* Note: had to re-pin the motor cables. On the plus side, they were long enough. Not sure if some wires needed to be extended or not.
	* It worked fine.		* It worked fine.
			* Note: Sara had pre-loaded Marlin onto the Arudino, cutting time down probably by 5-15 minutes.
	* Needs build phases and quality control points.		* Needs build phases and quality control points.

2018-10-29T21:28:09Z

Assembly & First Print

← Older revision		Revision as of 21:28, 29 October 2018
Line 62:		Line 62:

	=== Assembly & First Print ===		=== Assembly & First Print ===
	*		* Time spent:
			* Note: x & y axis movement looked good.

	=== Cable Chain + Final Touches ===		=== Cable Chain + Final Touches ===

2018-10-29T21:26:57Z

Axes

← Older revision		Revision as of 21:26, 29 October 2018
Line 16:		Line 16:
	* Order: 1 for the novice build		* Order: 1 for the novice build
	* Order: 3 for the intermediate build		* Order: 3 for the intermediate build
			* Improvement: change out the "do together" part and make it into its own build phase. This took a while to do in practice, more than 3 mins, more like 8 mins.

	=== Heated Bed ===		=== Heated Bed ===

2018-10-29T21:25:53Z

Control Panel

← Older revision		Revision as of 21:25, 29 October 2018
Line 54:		Line 54:

	=== Control Panel ===		=== Control Panel ===
	*		* Estimated time: 45 mins, 2 intermediate, 2 instructors
			* Note: was working a little too fast. Felt rushed. Late in day. Participant not absorbing a lot of the info.
			* Note: had to re-pin the motor cables. On the plus side, they were long enough. Not sure if some wires needed to be extended or not.
			* It worked fine.
			* Needs build phases and quality control points.

	=== Assembly & First Print ===		=== Assembly & First Print ===

2018-10-29T21:14:18Z

Extruder

← Older revision		Revision as of 21:14, 29 October 2018
Line 29:		Line 29:
	=== Extruder ===		=== Extruder ===
	* Order: 4		* Order: 4
	* Estimated time: 1.5-1.75 hours		* Estimated time: 1.5-1.75 hours, 1 intermediate and 1 instructor \| had a lot of re-work bc no documentation
			*

	==== Improvements ====		==== Improvements ====