OSE Roof Instructions - Revision history

Margaret Ida: /* ASSEMBLY SHEET FOR WORKSHOP ROOF FRAMES */

2011-09-16T02:01:45Z

ASSEMBLY SHEET FOR WORKSHOP ROOF FRAMES

← Older revision		Revision as of 02:01, 16 September 2011
Line 6:		Line 6:
	**3" deck nails		**3" deck nails
	**Carpenter's square		**Carpenter's square
	**25' tape ~~measure~~		**(2) 25' tape measures
	**Power screw driver(s)		**Power screw driver(s)
	* Lay out boards according to diagram, spacing 9 boards 2 feet apart.		* Lay out boards according to diagram, spacing 9 boards 2 feet apart.
Line 15:		Line 15:
	Build 24 roof frame assemblies		Build 24 roof frame assemblies
	[[File:Roof assembly layout.png]]		[[File:Roof assembly layout.png]]

	==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==		==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==
	* Assemble supplies and tools:		* Assemble supplies and tools:

Margaret Ida at 01:28, 16 September 2011

2011-09-16T01:28:21Z

← Older revision		Revision as of 01:28, 16 September 2011
Line 89:		Line 89:

	[[File:Roof Stringers.png]]		[[File:Roof Stringers.png]]
			==ROOF TIE ASSEMBLY SHEET==

			==TYING STRINGERS TO COLUMNS ASSEMBLY SHEET==

			==ROOF ASSEMBLY SHEET==

			==ROOF PANELS ASSEMBLY SHEET==

Margaret Ida at 00:01, 16 September 2011

2011-09-16T00:01:27Z

← Older revision		Revision as of 00:01, 16 September 2011
Line 14:		Line 14:

	Build 24 roof frame assemblies		Build 24 roof frame assemblies

	[[File:Roof assembly layout.png]]		[[File:Roof assembly layout.png]]

	==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==		==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==
	* Assemble supplies and tools:		* Assemble supplies and tools:

Margaret Ida at 23:43, 15 September 2011

2011-09-15T23:43:00Z

← Older revision		Revision as of 23:43, 15 September 2011
Line 1:		Line 1:
			==ASSEMBLY SHEET FOR WORKSHOP ROOF FRAMES==
			* Assemble supplies and tools:
			** Each Frame requires (11) 16’ 2x6” boards.
			**2-1/2 large tubes of Liquid Nails for each assembly
			**Large caulking gun(s)
			**3" deck nails
			**Carpenter's square
			**25' tape measure
			**Power screw driver(s)
			* Lay out boards according to diagram, spacing 9 boards 2 feet apart.
			* Butt each board to the two perpendicular ones, fastening with glue and screws according to diagram.
			* Verify square by checking that both diagonals are the same.
			* Maintain square by attaching lath or other scrap lumber diagonally across the frame.

			Build 24 roof frame assemblies

			[[File:Roof assembly layout.png]]

	==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==		==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==
	* Assemble supplies and tools:		* Assemble supplies and tools:
	**(14)2x6"x16' beams for each set of assemblies.		**(14)2x6"x16' beams for each set of assemblies.
	**2-1/2 large tubes of Liquid Nails for each assembly		**2-1/2 large tubes of Liquid Nails for each assembly
			**Large caulking gun(s)
	**3" deck nails		**3" deck nails
	**Circular saw		**Circular saw
	**Power source		**Power source
	**Pencil		**Pencil
	**Tape measure		**Tape measure (50')
	**Carpenter's square		**Carpenter's square
	**Power screw drivers		**Power screw drivers

Margaret Ida: /* ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS */

2011-09-14T03:48:38Z

ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS

← Older revision		Revision as of 03:48, 14 September 2011
Line 71:		Line 71:


	[[File:~~RoofStringers~~.png]]		[[File:Roof Stringers.png]]

Margaret Ida: /* ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS */

2011-09-14T03:37:15Z

ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS

← Older revision		Revision as of 03:37, 14 September 2011
Line 54:		Line 54:
	**Clamps (>5")		**Clamps (>5")
	**Saw horses		**Saw horses
	* Measure and mark ~~each of~~ the following beams		* Measure and mark the following beams
	**Next to the cut line mark the size of the board on that side of the line		**Next to the cut line mark the size of the board on that side of the line
	* Two 16’ 2x6” beam to create two 10’8” pieces and twoe 5’4” pieces.		* Two 16’ 2x6” beam to create two 10’8” pieces and twoe 5’4” pieces.
	* Lay out a supply shed stringer assembly as shown in the diagram.		* Lay out a supply shed stringer assembly as shown in the diagram.
	*Spread glue on the 5-1/~~2” faces~~ and screw together as shown in the detail at about 18” intervals.		* Start 2 screws at the end of each outside beam piece.
			* Spread glue on one 5-1/2” face of the center beam pieces.
			* Set one set of outside beams on the glued pieces.
			* Clamp at each beam end and screw together as shown in the detail, adding more screws at about 18” intervals.
			* Turn the assembly over and spread glue on the other 5-1/2" face of the center beam pieces.
			* Set the other set of outside beams on the glued pieces.
			* Clamp at each beam end and screw together as shown in the detail, adding more screws at about 18” intervals.

			Make 2 assemblies.

Margaret Ida: /* ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS */

2011-09-14T03:34:23Z

ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS

@@ Line 42: / Line 42: @@
 ==ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS==
-*Cut four 16’ 2x6” beams to create four 10’8” pieces and four 5’4” pieces.
+* Assemble supplies and tools:
-*Lay out a supply shed stringer assembly as shown in the diagram.
+**(6)2x6"x16' beams for each set of assemblies.
 *Spread glue on the 5-1/2” faces and screw together as shown in the detail at about 18” intervals.

Margaret Ida: /* ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS */

2011-09-14T03:30:25Z

ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS

← Older revision		Revision as of 03:30, 14 September 2011
Line 1:		Line 1:
	==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==		==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==
	* ~~Cut one~~ 16’ 2x6” beam to create one 10’8” piece and one 5’4” piece		* Assemble supplies and tools:
	* ~~Cut one~~ 16’ 2x6” beam to create one 10’ piece and one 6’ piece		**(14)2x6"x16' beams for each set of assemblies.
	*~~Cut two~~ 16’ 2x6” beams to create two ~~11’~~ pieces and two 5’ pieces		**2-1/2 large tubes of Liquid Nails for each assembly
	*~~Cut one~~ 16’ 2x6” ~~beams to 14’~~ in length.		**3" deck nails
	*~~Cut~~ a diagonal ~~piece off~~ one ~~11’ piece and~~ one ~~full 16’ piece as shown~~.		**Circular saw
	*Lay out a 32’ assembly as shown in the diagram		**Power source
	*Spread glue on ~~the~~ 5-1/2” ~~faces~~ and screw together as shown in the detail at about 18” intervals.		**Pencil
	*~~Lay out a 43”~~ assembly ~~as shown in the diagram.~~		**Tape measure
	*Spread glue on the 5-1/~~2” faces~~ and screw together as shown in the detail at about 18” intervals.		**Carpenter's square
			**Power screw drivers
			**Clamps (>5")
			**Saw horses
			* Measure and mark each of the following beams
			**Next to the cut line mark the size of the board on that side of the line
			* One 16’ 2x6” beam to create one 10’8” piece and one 5’4” piece
			* One 16’ 2x6” beam to create one 10’ piece and one 6’7/8" piece
			* Two 16’ 2x6” beams to create two 11’7/8" pieces and two 5’ pieces
			* One 16’ 2x6” beam at 15’ in length (cut off 1'7/8").
			* One 16’ 2x6” beam with a diagonal 1'9-7/8" from one end.
			* One of the 11'7/8" pieces with a diagonal 1'9-7/8" from one end
			* Cut the marked pieces.
			* Lay out a 32’ assembly as shown in the diagram
			* Start 2 screws at the end of each outside beam piece.
			* Spread glue on one 5-1/2” face of the center beam pieces.
			* Set one set of outside beams on the glued pieces.
			* Clamp at each beam end and screw together as shown in the detail, adding more screws at about 18” intervals.
			* Turn the assembly over and spread glue on the other 5-1/2" face of the center beam pieces.
			* Set the other set of outside beams on the glued pieces.
			* Clamp at each beam end and screw together as shown in the detail, adding more screws at about 18” intervals.

	~~Make~~ 5 of each assembly		* Lay out a 43”6-1/2" assembly as shown in the diagram.
			* Start 2 screws at the end of each outside beam piece.
			* Spread glue on one 5-1/2” face of the center beam pieces.
			* Set one set of outside beams on the glued pieces.
			* Clamp at each beam end and screw together as shown in the detail, adding more screws at about 18” intervals.
			* Turn the assembly over and spread glue on the other 5-1/2" face of the center beam pieces.
			* Set the other set of outside beams on the glued pieces. Be sure the points of the diagonal cuts are on the same side of the stringer.
			* Clamp at each beam end and screw together as shown in the detail, adding more screws at about 18” intervals.

			Make (5) 32" workshop assemblies and (5) 43"6-1/2" assemblies.

	==ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS==		==ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS==

Margaret Ida: /* ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS */

2011-09-13T18:13:29Z

ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS

← Older revision		Revision as of 18:13, 13 September 2011
Line 23:		Line 23:


	[[~~file~~:RoofStringers.png]]		[[File:RoofStringers.png]]

Margaret Ida at 18:12, 13 September 2011

2011-09-13T18:12:41Z

← Older revision		Revision as of 18:12, 13 September 2011
Line 1:		Line 1:
			==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS==
	==ASSEMBLY SHEET FOR WORKSHOP ROOF STRINGERS
	* Cut one 16’ 2x6” beam to create one 10’8” piece and one 5’4” piece		* Cut one 16’ 2x6” beam to create one 10’8” piece and one 5’4” piece
	* Cut one 16’ 2x6” beam to create one 10’ piece and one 6’ piece		* Cut one 16’ 2x6” beam to create one 10’ piece and one 6’ piece
Line 16:		Line 15:


	==ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS		==ASSEMBLY SHEET FOR SUPPLY SHED ROOF STRINGERS==
	*Cut four 16’ 2x6” beams to create four 10’8” pieces and four 5’4” pieces.		*Cut four 16’ 2x6” beams to create four 10’8” pieces and four 5’4” pieces.
	*Lay out a supply shed stringer assembly as shown in the diagram.		*Lay out a supply shed stringer assembly as shown in the diagram.