PowerCube6 Pump Mount - Revision history

Tom Griffing: /* Engine Mounts and Hydraulic Pump Mount */

2012-08-18T04:29:45Z

Engine Mounts and Hydraulic Pump Mount

← Older revision		Revision as of 04:29, 18 August 2012
Line 9:		Line 9:
	::[[Image:PumpAngle.png]]		::[[Image:PumpAngle.png]]

	==Engine ~~Mounts and Hydraulic~~ Pump Mount==		==Engine / Pump Mount Assembly==

	* ~~Prepare~~ the pump plate		* Align the two 1/4" x 2" x 2" anglt iron pieces on the pump plate as shown below and weld securely.

	* Bolt the ¼” x 2” x 2” x 8” plate to the ¼” x 2” x 2” x 29” angle as shown using 1/2” x 2” bolts:		::[[Image:PumpAngleWeld.png\|500px]]

	::[[~~Image:EngineMountLower~~.~~png]]~~		* Mount the engine to the engine plate using [4] 5/16” x 2” bolts and [4] rubber vibration mounts.

	* ~~Bolt~~ the ~~¼” x 8” x 12” plate to~~ the ~~8" angle as shown using 1/2” x 2” bolts:~~		* Slide the shaft coupling onto the engine shaft and secure the hex screw.

	::[~~[Image:EngineMountUpper~~.~~png]]~~		* Mount the pump onto the pump plate and secure with [2] 7/16" x 1 1/2" bolts.

	* ~~Align~~ the plate ~~edges~~ and ~~secure at 90 degree angle and weld~~. ~~We use welding magnets to hold the plates at 90 degrees:~~		* Slide the splined pump shaft into the shaft coupling so the angle touches the engine plate and is oriented as shown.

	~~::[[Image:EngineMountWeld.png\|500px]]~~		See the following video for details:

	* Mount the engine to the engine plate using [4] 5/16” x 2” bolts. The method for mounting may depend on your engine. See the following video for details:

	::{{YoutubePopup\|DO6wbwOjWNA\|\|powercube-window}}		::{{YoutubePopup\|DO6wbwOjWNA\|\|powercube-window}}

	* Examine the engine shaft – it should be 2” long. If longer, cut the shaft to extend no more than 2” from the case. This length is necessary for the coupling. Put the larger keystock in the engine shaft and slide the shaft coupling on the engine shaft and tighten the allen screws to hold it in place.		* Examine the engine shaft – it should be 2” long. If longer, cut the shaft to extend no more than 2” from the case. This length is necessary for the coupling. Put the larger keystock in the engine shaft and slide the shaft coupling on the engine shaft and tighten the allen screws to hold it in place.

Tom Griffing: /* Engine Mounting Plates */

2012-08-16T22:13:40Z

Engine Mounting Plates

← Older revision		Revision as of 22:13, 16 August 2012
Line 1:		Line 1:
	==Engine Mounting Plates==		==Engine Mounting Plates==
	* ¼” x 8” x 13.5” Plate		* ¼” x 8” x 13.5” Plate
			::[[Image:EnginePlate.png]]

	* ¼” x 6” x 6” Plate		* ¼” x 6” x 6” Plate
			::[[Image:PumpPlate.png]]

	* ¼” x 2” x 2” x 5” Angle (2 ea)		* ¼” x 2” x 2” x 5” Angle (2 ea)
			::[[Image:PumpAngle.png]]
	::[[Image:~~PumpMount~~.png]]

	==Engine Mounts and Hydraulic Pump Mount==		==Engine Mounts and Hydraulic Pump Mount==

Tom Griffing: Created page with "==Engine Mounting Plates== * ¼” x 8” x 13.5” Plate * ¼” x 6” x 6” Plate * ¼” x 2” x 2” x 5” Angle (2 ea) ::Image:PumpMount.png ==Engine Mounts and Hy..."

2012-08-16T22:03:47Z

Created page with "==Engine Mounting Plates== * ¼” x 8” x 13.5” Plate * ¼” x 6” x 6” Plate * ¼” x 2” x 2” x 5” Angle (2 ea) ::Image:PumpMount.png ==Engine Mounts and Hy..."

New page

==Engine Mounting Plates==
* ¼” x 8” x 13.5” Plate
* ¼” x 6” x 6” Plate
* ¼” x 2” x 2” x 5” Angle (2 ea)

::[[Image:PumpMount.png]]

==Engine Mounts and Hydraulic Pump Mount==

* Prepare the pump plate

* Bolt the ¼” x 2” x 2” x 8” plate to the ¼” x 2” x 2” x 29” angle as shown using 1/2” x 2” bolts:

::[[Image:EngineMountLower.png]]

* Bolt the ¼” x 8” x 12” plate to the 8" angle as shown using 1/2” x 2” bolts:

::[[Image:EngineMountUpper.png]]

* Align the plate edges and secure at 90 degree angle and weld. We use welding magnets to hold the plates at 90 degrees:

::[[Image:EngineMountWeld.png|500px]]

* Mount the engine to the engine plate using [4] 5/16” x 2” bolts. The method for mounting may depend on your engine. See the following video for details:

::{{YoutubePopup|DO6wbwOjWNA||powercube-window}}

* Examine the engine shaft – it should be 2” long. If longer, cut the shaft to extend no more than 2” from the case. This length is necessary for the coupling. Put the larger keystock in the engine shaft and slide the shaft coupling on the engine shaft and tighten the allen screws to hold it in place.