PowerCube Engine & Hydraulic Pump mounts - Revision history

Tom Griffing: /* Engine Mounts and Hydraulic Pump Mount */

2012-01-05T11:07:14Z

Engine Mounts and Hydraulic Pump Mount

← Older revision		Revision as of 11:07, 5 January 2012
Line 44:		Line 44:
	::[[Image:PumpMountBolts.png]]		::[[Image:PumpMountBolts.png]]

	* Mount the pump to the pump plate using [2] 7/16 bolts, nuts and washers:		* Mount the pump to the pump plate using [2] 7/16 bolts, nuts, lock washers and flat washers:

	::[[Image:PumpMountPump.png]]		::[[Image:PumpMountPump.png]]

Tom Griffing: /* Engine Mounts and Hydraulic Pump Mount */

2012-01-05T11:05:31Z

Engine Mounts and Hydraulic Pump Mount

← Older revision		Revision as of 11:05, 5 January 2012
Line 30:		Line 30:
	* Align the plate edges and secure at 90 degree angle and weld. We use welding magnets to hold the plates at 90 degrees:		* Align the plate edges and secure at 90 degree angle and weld. We use welding magnets to hold the plates at 90 degrees:

	::[[Image:EngineMountWeld.png]]		::[[Image:EngineMountWeld.png\|500px]]

	* Mount the engine to the engine plate using [4] 5/16” x 2” bolts. The method for mounting may depend on your engine. See the following video for details:		* Mount the engine to the engine plate using [4] 5/16” x 2” bolts. The method for mounting may depend on your engine. See the following video for details:

Tom Griffing: /* Engine Mounting Plates */

2012-01-05T10:54:15Z

Engine Mounting Plates

← Older revision		Revision as of 10:54, 5 January 2012
Line 17:		Line 17:

	::{{YoutubePopup\|1s4SbXQp38s\|big\|powercube-window}}		::{{YoutubePopup\|1s4SbXQp38s\|big\|powercube-window}}

			==Engine Mounts and Hydraulic Pump Mount==

			* Bolt the ¼” x 2” x 2” x 8” plate to the ¼” x 2” x 2” x 29” angle as shown using 1/2” x 2” bolts:

			::[[Image:EngineMountLower.png]]

			* Bolt the ¼” x 8” x 12” plate to the 8" angle as shown using 1/2” x 2” bolts:

			::[[Image:EngineMountUpper.png]]

			* Align the plate edges and secure at 90 degree angle and weld. We use welding magnets to hold the plates at 90 degrees:

			::[[Image:EngineMountWeld.png]]

			* Mount the engine to the engine plate using [4] 5/16” x 2” bolts. The method for mounting may depend on your engine. See the following video for details:

			::{{YoutubePopup\|DO6wbwOjWNA\|\|powercube-window}}

			* Examine the engine shaft – it should be 2” long. If longer, cut the shaft to extend no more than 2” from the case. This length is necessary for the coupling. Put the larger keystock in the engine shaft and slide the shaft coupling on the engine shaft and tighten the allen screws to hold it in place.

			::[[Image:EngineMountCoupling.png]]

			* Assemble the 8” x 8” pump plate as shown with [4] ¾” x 3.5” bolts and [8] 3/4” nuts, [8] washers and [4] lockwashers. Tighten the nuts to hold the plate firmly:

			::[[Image:PumpMountBolts.png]]

			* Mount the pump to the pump plate using [2] 7/16 bolts, nuts and washers:

			::[[Image:PumpMountPump.png]]

			* Make sure the key is in the pump shaft and slide the pump shaft into the bottom of the shaft coupling and tighten its allen screws. The bolt heads should just be touching the bottom of the engine plate. Tack and weld the bolt heads to the engine plate.

			::[[Image:EnginePumpAssembly.png]]

			* Lower the engine/pump assembly into the frame. Adjust it so the engine plate is parallel with the frame and weld the 8” angle iron to the reservoir and the 29” angle iron to the frame.

			::[[Image:EnginePumpInstalled.png]]

Tom Griffing at 09:31, 5 January 2012

2012-01-05T09:31:40Z

← Older revision		Revision as of 09:31, 5 January 2012
Line 9:		Line 9:
	::[[Image:EngineMount2.png\|845px]]		::[[Image:EngineMount2.png\|845px]]

	~~==Pump Support==~~
	* ¼” x 5” x 5” Plate
	* [2] ¼” x 2” x 2” x 5” Angle
	* [2] 7/16" nuts

	~~::[[Image:EnginePumpSupport.png\|600px]]~~

	Torching of engine mounts:		Torching of engine mounts:

Tom Griffing: /* Engine Mounting Plates */

2012-01-05T09:31:10Z

Engine Mounting Plates

← Older revision		Revision as of 09:31, 5 January 2012
Line 2:		Line 2:
	* ¼” x 8” x 12” Plate		* ¼” x 8” x 12” Plate
	* ¼” x 8” x 9” Plate		* ¼” x 8” x 9” Plate
			* ¼” x 8” x 8” Plate
	* ¼” x 2” x 2” x 8” Angle		* ¼” x 2” x 2” x 8” Angle
	* ¼” x 2” x 2” x 29” Angle		* ¼” x 2” x 2” x 29” Angle

Tom Griffing: /* Pump Support */

2011-12-14T02:46:21Z

Pump Support

← Older revision		Revision as of 02:46, 14 December 2011
Line 11:		Line 11:
	* ¼” x 5” x 5” Plate		* ¼” x 5” x 5” Plate
	* [2] ¼” x 2” x 2” x 5” Angle		* [2] ¼” x 2” x 2” x 5” Angle
			* [2] 7/16" nuts

	::[[Image:EnginePumpSupport.png\|600px]]		::[[Image:EnginePumpSupport.png\|600px]]

Tom Griffing at 02:45, 14 December 2011

2011-12-14T02:45:52Z

← Older revision		Revision as of 02:45, 14 December 2011
Line 1:		Line 1:
	===Engine ~~& Hydraulic Pump mounts=~~==		==Engine Mounting Plates==
	* ¼” x 8” x 12” Plate		* ¼” x 8” x 12” Plate
	* ¼” x 8” x 9” Plate		* ¼” x 8” x 9” Plate
Line 8:		Line 8:
	::[[Image:EngineMount2.png\|845px]]		::[[Image:EngineMount2.png\|845px]]

	~~Engine /~~ Pump ~~support~~		==Pump Support==
	* ¼” x 5” x 5” Plate		* ¼” x 5” x 5” Plate
	* [2] ¼” x 2” x 2” x 5” Angle		* [2] ¼” x 2” x 2” x 5” Angle
Line 19:		Line 19:

	And, torching the last of the 9 power cube engine mount plate holes:		And, torching the last of the 9 power cube engine mount plate holes:

	::{{YoutubePopup\|1s4SbXQp38s\|big\|powercube-window}}		::{{YoutubePopup\|1s4SbXQp38s\|big\|powercube-window}}

Tom Griffing at 02:44, 14 December 2011

2011-12-14T02:44:30Z

← Older revision		Revision as of 02:44, 14 December 2011
Line 4:		Line 4:
	* ¼” x 2” x 2” x 8” Angle		* ¼” x 2” x 2” x 8” Angle
	* ¼” x 2” x 2” x 29” Angle		* ¼” x 2” x 2” x 29” Angle
	* ¼” x 5” x 5” Plate

	::[[Image:EngineMount2.png\|845px]]		::[[Image:EngineMount2.png\|845px]]

	Engine / Pump support		Engine / Pump support
			* ¼” x 5” x 5” Plate
			* [2] ¼” x 2” x 2” x 5” Angle

	::[[Image:EnginePumpSupport.png\|600px]]		::[[Image:EnginePumpSupport.png\|600px]]

Tom Griffing: /* Engine & Hydraulic Pump mounts */

2011-12-14T02:43:38Z

Engine & Hydraulic Pump mounts

← Older revision		Revision as of 02:43, 14 December 2011
Line 4:		Line 4:
	* ¼” x 2” x 2” x 8” Angle		* ¼” x 2” x 2” x 8” Angle
	* ¼” x 2” x 2” x 29” Angle		* ¼” x 2” x 2” x 29” Angle
	* ¼” x 8” x 8” Plate		* ¼” x 5” x 5” Plate

	::[[Image:EngineMount2.png\|845px]]		::[[Image:EngineMount2.png\|845px]]

Tom Griffing: /* Engine & Hydraulic Pump mounts */

2011-12-14T02:21:59Z

Engine & Hydraulic Pump mounts

← Older revision		Revision as of 02:21, 14 December 2011
Line 10:		Line 10:
	Engine / Pump support		Engine / Pump support

	::[[Image:~~EngineMount2~~.png\|~~845px~~]]		::[[Image:EnginePumpSupport.png\|600px]]

	Torching of engine mounts:		Torching of engine mounts: