PowerCube Wiring - Revision history

KhalidH at 22:40, 27 December 2013

2013-12-27T22:40:12Z

← Older revision		Revision as of 22:40, 27 December 2013
Line 20:		Line 20:
	===Operation===		===Operation===
	* The Magneto is connected to ground in order to kill the engine		* The Magneto is connected to ground in order to kill the engine
			[[category:Power Cube]]

Zdwiel at 03:25, 18 May 2013

2013-05-18T03:25:22Z

← Older revision		Revision as of 03:25, 18 May 2013
Line 4:		Line 4:
	* Connect the remaining wires, as in the diagram below:		* Connect the remaining wires, as in the diagram below:
	::[[Image:wiringdiagram.png]]		::[[Image:wiringdiagram.png]]
	* Position of terminals on keyswitch:
	~~::[[Image:4302492L.jpg]]~~

	Wiring Diagrams:		Wiring Diagrams:

Zdwiel at 01:37, 18 May 2013

2013-05-18T01:37:04Z

← Older revision		Revision as of 01:37, 18 May 2013
Line 19:		Line 19:
	**I - Ignition		**I - Ignition
	* Note that the thicker lines represent the heavier wires that will carry high electrical current.		* Note that the thicker lines represent the heavier wires that will carry high electrical current.

			===Operation===
			* The Magneto is connected to ground in order to kill the engine

Zdwiel at 01:36, 18 May 2013

2013-05-18T01:36:08Z

← Older revision		Revision as of 01:36, 18 May 2013
Line 4:		Line 4:
	* Connect the remaining wires, as in the diagram below:		* Connect the remaining wires, as in the diagram below:
	::[[Image:wiringdiagram.png]]		::[[Image:wiringdiagram.png]]
			* Position of terminals on keyswitch:
			::[[Image:4302492L.jpg]]

	Wiring Diagrams:		Wiring Diagrams:
	*[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]		*[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]

Gabrielle LeBlanc at 22:54, 12 October 2012

2012-10-12T22:54:22Z

← Older revision		Revision as of 22:54, 12 October 2012
Line 7:		Line 7:
	*[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]		*[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]
	*[http://www.mytractorforum.com/showthread.php?t=216425 For More Information]		*[http://www.mytractorforum.com/showthread.php?t=216425 For More Information]
			*Terminal letters are decoded as follows:

			**B - Battery
			**A - Accessory
			**R - Regulator
			**S - Starter Solenoid
			**M - Magneto
			**I - Ignition
	* Note that the thicker lines represent the heavier wires that will carry high electrical current.		* Note that the thicker lines represent the heavier wires that will carry high electrical current.

Gabrielle LeBlanc at 22:50, 12 October 2012

2012-10-12T22:50:45Z

← Older revision		Revision as of 22:50, 12 October 2012
Line 4:		Line 4:
	* Connect the remaining wires, as in the diagram below:		* Connect the remaining wires, as in the diagram below:
	::[[Image:wiringdiagram.png]]		::[[Image:wiringdiagram.png]]
	[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]		Wiring Diagrams:
			*[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]
			*[http://www.mytractorforum.com/showthread.php?t=216425 For More Information]

	* Note that the thicker lines represent the heavier wires that will carry high electrical current.		* Note that the thicker lines represent the heavier wires that will carry high electrical current.

Gabrielle LeBlanc at 22:49, 12 October 2012

2012-10-12T22:49:53Z

← Older revision		Revision as of 22:49, 12 October 2012
Line 4:		Line 4:
	* Connect the remaining wires, as in the diagram below:		* Connect the remaining wires, as in the diagram below:
	::[[Image:wiringdiagram.png]]		::[[Image:wiringdiagram.png]]
			[http://www.stens.com/images/catalog2/430-249_2_C.jpg Wiring Diagram for Prime Line SBRAI ignition switch]

	* Note that the thicker lines represent the heavier wires that will carry high electrical current.		* Note that the thicker lines represent the heavier wires that will carry high electrical current.

Tom Griffing: Created page with "===Wiring=== * The keyswitch has spade connectors for wiring and bolts to the frame for stability. These should be connected with matching crimp-on connectors. ::[[Image:keyswit..."

2011-12-12T04:25:04Z

Created page with "===Wiring=== * The keyswitch has spade connectors for wiring and bolts to the frame for stability. These should be connected with matching crimp-on connectors. ::[[Image:keyswit..."

New page

===Wiring===
* The keyswitch has spade connectors for wiring and bolts to the frame for stability. These should be connected with matching crimp-on connectors.
::[[Image:keyswitch.jpg]]
* Connect the remaining wires, as in the diagram below:
::[[Image:wiringdiagram.png]]
* Note that the thicker lines represent the heavier wires that will carry high electrical current.