Sara Build Certification Outline - Revision history

Secbajor: /* Certification Procedure */

2018-12-05T00:26:21Z

Certification Procedure

← Older revision		Revision as of 00:26, 5 December 2018
Line 59:		Line 59:
	#An SD Card containing GCode for printing a Test Cube		#An SD Card containing GCode for printing a Test Cube

	'''Complete the Build Certification Presentation'''		'''Complete the Build Certification Presentation.'''
	The Build Certification Presentation is the method by which the applicant submits the required materials for review by OSE. Each module of the Certification is a timed build of a component of the 3D Printer. The final module is the assembly of the printer from the parts prepared in the preceding modules. These modules should be completed one by one in the order laid out in the Build Certification Presentation. In the case where an applicant exceeds the time limit for a module, the applicant should re-build the component, until it can be completed within the time limit.		The Build Certification Presentation is the method by which the applicant submits the required materials for review by OSE. Each module of the Certification is a timed build of a component of the 3D Printer. The final module is the assembly of the printer from the parts prepared in the preceding modules. These modules should be completed one by one in the order laid out in the Build Certification Presentation. In the case where an applicant exceeds the time limit for a module, the applicant should re-build the component, until it can be completed within the time limit.

Secbajor: /* Certification Procedure */

2018-12-05T00:25:27Z

Certification Procedure

← Older revision		Revision as of 00:25, 5 December 2018
Line 67:		Line 67:
	* Build time '''(applicants don't have to do this if we figure out how long each timelapse needs to be to make time limit)'''		* Build time '''(applicants don't have to do this if we figure out how long each timelapse needs to be to make time limit)'''

	Upon completion of the Build Certification Presentation, email info@opensourceecology.org with a link to ~~[Your D3D~~ Certification ~~Build]~~. Your application will be reviewed and you will be contacted with any re-work needed to successfully obtain Certification.		Upon completion of the Build Certification Presentation, email info@opensourceecology.org with a link to your Build Certification page. Your application will be reviewed and you will be contacted with any re-work needed to successfully obtain Certification.

	=Reasonable Accommodations=		=Reasonable Accommodations=

Secbajor at 00:24, 5 December 2018

2018-12-05T00:24:41Z

@@ Line 69: / Line 69: @@
 Upon completion of the Build Certification Presentation, email info@opensourceecology.org with a link to [Your D3D Certification Build]. Your application will be reviewed and you will be contacted with any re-work needed to successfully obtain Certification.
-'''TODO: deprecate the following sections'''
+=Reasonable Accommodations=
 The Build Certification Presentation requires the following completion times:
@@ Line 86: / Line 89: @@
 It is noted that if the applicant fails to achieve Certification because of a failure to submit images for consideration, the Build Certification must be restarted from the beginning. The art of refining the 3D Printer to produce prints of high quality requires knowledge and intuition, so applicants are encouraged to practice achieving high quality prints while receiving feedback from OSE until their working knowledge of the printer enables them to confidently operate the printer for the entirety of its lifetime.

Secbajor: /* Certification Procedure */

2018-12-05T00:24:01Z

Certification Procedure

← Older revision		Revision as of 00:24, 5 December 2018
Line 66:		Line 66:
	* Completion photos		* Completion photos
	* Build time '''(applicants don't have to do this if we figure out how long each timelapse needs to be to make time limit)'''		* Build time '''(applicants don't have to do this if we figure out how long each timelapse needs to be to make time limit)'''

			Upon completion of the Build Certification Presentation, email info@opensourceecology.org with a link to [Your D3D Certification Build]. Your application will be reviewed and you will be contacted with any re-work needed to successfully obtain Certification.

			'''TODO: deprecate the following sections'''

	The Build Certification Presentation requires the following completion times:		The Build Certification Presentation requires the following completion times:
Line 77:		Line 81:
	# Control panel assembly within 25 minutes		# Control panel assembly within 25 minutes

	~~'''TODO: deprecate the following sections'''~~
	'''Complete a 6-Hour Build.''' The individual will then complete the build within 7 hours (6 hours building, 1 hour break) while generating the submission materials needed to receive Certification. The Build Time shall be marked as the time from the beginning of '''frame assembly''' to the finish of a Test Cube. The quality of the Test Cube is not vital at this point, but needs to be refined until high quality is achieved for an individual to receive Certification.		'''Complete a 6-Hour Build.''' The individual will then complete the build within 7 hours (6 hours building, 1 hour break) while generating the submission materials needed to receive Certification. The Build Time shall be marked as the time from the beginning of '''frame assembly''' to the finish of a Test Cube. The quality of the Test Cube is not vital at this point, but needs to be refined until high quality is achieved for an individual to receive Certification.

Secbajor: /* Certification Procedure */

2018-12-05T00:22:02Z

Certification Procedure

← Older revision		Revision as of 00:22, 5 December 2018
Line 50:		Line 50:
	=Certification Procedure=		=Certification Procedure=

	~~The~~ applicant ~~must embed each of~~ the following ~~as a timelapse video embedded in [[Your Name Build Certification]]. (The timelapse should be made using Open Camera~~ - ~~a free~~-~~to-download smart phone application available in Google Play~~ and ~~iPhone's App Store~~ - ~~set~~ to ~~10 second intervals~~ and ~~compiled into a timelapse using the instructions here: [[https://wiki~~.~~opensourceecology~~.~~org/wiki/OpenCamera~~#~~D3D_Certification_Command Open Camera]])~~		'''Acquire Necessary Supplies.''' In addition to the Kit, the applicant should prepare the following supplies to complete the build:
			#JB weld mixer and applicator - for building frame
			#Crazy glue - for attaching cable chain and end stops
			#Electrical tape - for fixing wires to frame and bundling them
			#Silver sharpie or Masking Tape with Black Sharpie - for marking plugs
			#0.4 mm needle - for unclogging nozzle
			#Sample PLA filament for initial printing - either 1.75mm or 2.85mm
			#An SD Card containing GCode for printing a Test Cube

	~~Make~~ a ~~copy~~ of the Build Certification Presentation ~~and replace~~ the following on each ~~slide~~:		'''Complete the Build Certification Presentation'''
	* Timelapse (upload to YouTube, then add to Presentation with Insert > Video > By URL)		The Build Certification Presentation is the method by which the applicant submits the required materials for review by OSE. Each module of the Certification is a timed build of a component of the 3D Printer. The final module is the assembly of the printer from the parts prepared in the preceding modules. These modules should be completed one by one in the order laid out in the Build Certification Presentation. In the case where an applicant exceeds the time limit for a module, the applicant should re-build the component, until it can be completed within the time limit.

			A completed Build Certification Presentation is ready for submission to OSE when the following have been included by the applicant for each module:
			* Timelapse (create using free-to-download smart phone app "Open Camera", follow the [https://wiki.opensourceecology.org/wiki/OpenCamera#D3D_Certification_Command Open Camera instructions here], upload to YouTube, then add to Presentation with Insert > Video > By URL)
	* Completion photos		* Completion photos
	* ~~Time~~ '''(applicants don't have to do this if we figure out how long each timelapse needs to be to make time limit)'''		* Build time '''(applicants don't have to do this if we figure out how long each timelapse needs to be to make time limit)'''

			The Build Certification Presentation requires the following completion times:
	# Frame assembly within 60 minutes		# Frame assembly within 60 minutes
	# Y-left and Z-back axis assembly within 18 minutes		# Y-left and Z-back axis assembly within 18 minutes
Line 66:		Line 77:
	# Control panel assembly within 25 minutes		# Control panel assembly within 25 minutes

	'''~~Acquire Necessary Supplies.''' In addition to the Kit, the applicant should prepare~~ the following ~~supplies to complete the build:~~		'''TODO: deprecate the following sections'''
	~~#JB weld mixer and applicator - for building frame~~
	~~#Crazy glue - for attaching cable chain and end stops~~
	~~#Electrical tape - for fixing wires to frame and bundling them~~
	~~#Silver sharpie or Masking Tape with Black Sharpie - for marking plugs~~
	~~#0.4 mm needle - for unclogging nozzle~~
	~~#Sample PLA filament for initial printing - either 1.75mm or 2.85mm~~
	~~#An SD Card containing GCode for printing a Test Cube~~

	'''Schedule a Build Day.''' When your intention to pursue Build Certification is received, an OSE representative will contact you to schedule a day and start time for the build. Before the build begins on the scheduled day, the OSE representative will check in via conference call to confirm the beginning time of the build.

	'''Complete a 6-Hour Build.''' The individual will then complete the build within 7 hours (6 hours building, 1 hour break) while generating the submission materials needed to receive Certification. The Build Time shall be marked as the time from the beginning of '''frame assembly''' to the finish of a Test Cube. The quality of the Test Cube is not vital at this point, but needs to be refined until high quality is achieved for an individual to receive Certification.		'''Complete a 6-Hour Build.''' The individual will then complete the build within 7 hours (6 hours building, 1 hour break) while generating the submission materials needed to receive Certification. The Build Time shall be marked as the time from the beginning of '''frame assembly''' to the finish of a Test Cube. The quality of the Test Cube is not vital at this point, but needs to be refined until high quality is achieved for an individual to receive Certification.

Secbajor: /* Requesting Certification */

2018-12-05T00:13:44Z

Requesting Certification

← Older revision		Revision as of 00:13, 5 December 2018
Line 45:		Line 45:
	After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:		After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:
	* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval		* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval
	* Create your own copy of the presentation on [[D3D Build Certification Application]] and embed on a new page called [[Your Name D3D Build Certification]] (Requires a Wiki account; see [[https://wiki.opensourceecology.org/wiki/Sara_D3D_Build_Certification example]])		* Create your own copy of the presentation on [[D3D Build Certification Application]] and embed on a new page called [[Your Name D3D Build Certification]] (Requires a Wiki account; see [https://wiki.opensourceecology.org/wiki/Sara_D3D_Build_Certification example])
	* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.		* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.

Secbajor: /* Requesting Certification */

2018-12-05T00:13:25Z

Requesting Certification

← Older revision		Revision as of 00:13, 5 December 2018
Line 45:		Line 45:
	After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:		After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:
	* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval		* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval
	* Create your own copy of the presentation on [[D3D Build Certification Application]] and embed on a new page called [[Your Name Build Certification]] (Requires a Wiki account.)		* Create your own copy of the presentation on [[D3D Build Certification Application]] and embed on a new page called [[Your Name D3D Build Certification]] (Requires a Wiki account; see [[https://wiki.opensourceecology.org/wiki/Sara_D3D_Build_Certification example]])
	* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.		* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.

Secbajor: /* Requesting Certification */

2018-12-05T00:10:02Z

Requesting Certification

← Older revision		Revision as of 00:10, 5 December 2018
Line 45:		Line 45:
	After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:		After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:
	* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval		* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval
	* Create your own copy of the presentation on [[Build ~~Procedure~~]] and embed on a new page called [[Your Name Build Certification]] (Requires a Wiki account.)		* Create your own copy of the presentation on [[D3D Build Certification Application]] and embed on a new page called [[Your Name Build Certification]] (Requires a Wiki account.)
	* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.		* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.

Secbajor: /* Requesting Certification */

2018-12-05T00:09:01Z

Requesting Certification

← Older revision		Revision as of 00:09, 5 December 2018
Line 44:		Line 44:
	=Requesting Certification=		=Requesting Certification=
	After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:		After achieving mastery of the steps recommended above, an individual can request Build Certification from OSE by completing the following:
	* Acquire a Kit by purchasing one from OSE or purchasing the parts independently and submitting [[Kit Certification]] for OSE approval		* Acquire a Kit by purchasing one from OSE '''or''' purchasing the parts independently and submitting [[Kit Certification]] for OSE approval
	* Create your own copy of the presentation on [[Build Procedure]] and embed on a new page called [[Your Name Build Certification]] (Requires a Wiki account.)		* Create your own copy of the presentation on [[Build Procedure]] and embed on a new page called [[Your Name Build Certification]] (Requires a Wiki account.)
	* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.		* Email info@opensourceecology.org with a link to your Build Certification page and a written statement of your intention to pursue Build Certification. Include any comments or feedback on completing the Prerequisites.

	=Certification Procedure=		=Certification Procedure=

Secbajor: /* Prerequisites */

2018-12-05T00:08:35Z

Prerequisites

← Older revision		Revision as of 00:08, 5 December 2018
Line 29:		Line 29:
	* Ability to use OpenCamera on a smartphone - demonstrated by creating a timelapse with the picture rate set to 10 second intervals and compiled using the instructions here: [[https://wiki.opensourceecology.org/wiki/OpenCamera#D3D_Certification_Command Open Camera]])		* Ability to use OpenCamera on a smartphone - demonstrated by creating a timelapse with the picture rate set to 10 second intervals and compiled using the instructions here: [[https://wiki.opensourceecology.org/wiki/OpenCamera#D3D_Certification_Command Open Camera]])
	* Ability to use JB Kwik Weld effectively so that frame can be assembled securely		* Ability to use JB Kwik Weld effectively so that frame can be assembled securely
	* Assembly of ~~one~~ Y- ~~or Z-axis~~ axis within 9 minutes		* Assembly of the Y-left axis within 9 minutes
	* Knowledge of how the Y-~~left~~ axis differs from the Y-~~right~~ axis		* Knowledge of how the Y-right axis differs from the Y-left axis
	* Knowledge of how the X-axis differs from the other axes		* Knowledge of how the X-axis differs from the other axes
	* Assembly of the Extruder within 25 minutes		* Assembly of the Extruder within 25 minutes