Shelf Mounting Procedure - Revision history

Marcin: /* 20 Foot Shelves */

2016-04-13T05:51:38Z

20 Foot Shelves

← Older revision		Revision as of 05:51, 13 April 2016
Line 14:		Line 14:
	#Mount the 2x6 blocks, 4.5" long - at every 4 feet for attaching the hanger strap.		#Mount the 2x6 blocks, 4.5" long - at every 4 feet for attaching the hanger strap.
	#Use 25" hanger straps for.hanging the shelf.		#Use 25" hanger straps for.hanging the shelf.
			#Use 36" hanger straps for handling the 2' wide shelves.

Marcin: /* 20 Foot Shelves */

2016-04-13T01:53:51Z

20 Foot Shelves

← Older revision		Revision as of 01:53, 13 April 2016
Line 3:		Line 3:
	#Mount the 70 lb angle bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends. Use a level to keep a level over the 20 feet.		#Mount the 70 lb angle bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends. Use a level to keep a level over the 20 feet.
	#Mount the 6x board first.		#Mount the 6x board first.
	#Mount the 8' plywood strip on back of the two 6" boards, on outside. Do not do this in situ. The ID piece of about 4' long will be cut to size later.		#Mount the 8' plywood strip on back of the two 6" boards, on outside. Do not do this in situ. The mid piece of about 4' long will be cut to size later.
	#Also mount the 12" connecting strip to one of the 6" boards.		#Also mount the 12" connecting strip to one of the 6" boards.
	#Also mount the 13.75" strip of plywood on each side.		#Also mount the 13.75" strip of plywood on each side.

Marcin: /* 20 Foot Shelves */

2016-04-13T01:53:12Z

20 Foot Shelves

← Older revision		Revision as of 01:53, 13 April 2016
Line 13:		Line 13:
	#Attach the shelves to the brackets.		#Attach the shelves to the brackets.
	#Mount the 2x6 blocks, 4.5" long - at every 4 feet for attaching the hanger strap.		#Mount the 2x6 blocks, 4.5" long - at every 4 feet for attaching the hanger strap.
			#Use 25" hanger straps for.hanging the shelf.

Marcin: /* 20 Foot Shelves */

2016-04-13T01:50:08Z

20 Foot Shelves

← Older revision		Revision as of 01:50, 13 April 2016
Line 8:		Line 8:
	#Join the two 10 foot sections by the back strip, cut to size, and by the mid connecting piece from the bottom using 1.5" screws - 2 on each side. Move the shelf away from the glazing wall to screw in the connecting piece.		#Join the two 10 foot sections by the back strip, cut to size, and by the mid connecting piece from the bottom using 1.5" screws - 2 on each side. Move the shelf away from the glazing wall to screw in the connecting piece.
	#Mount the 2x8 to the end strip on the side at the greenhouse corner. With this attached, the corner end can be shuffled to the corner, ready for attachment to the brackets.		#Mount the 2x8 to the end strip on the side at the greenhouse corner. With this attached, the corner end can be shuffled to the corner, ready for attachment to the brackets.
			#Use 1.5" screws first to pull the shelf towards the glazing wall by screwing into the glazing wall studs at every 4 feet.
			#Add the last 2x8. Attach to the mid connector and end connector.
			#Mount the front strips, first the 8 footers outside, then the mid piece cut to length of about 4'.
			#Attach the shelves to the brackets.
			#Mount the 2x6 blocks, 4.5" long - at every 4 feet for attaching the hanger strap.

Marcin: /* 20 Foot Shelves */

2016-04-13T01:44:16Z

20 Foot Shelves

← Older revision		Revision as of 01:44, 13 April 2016
Line 3:		Line 3:
	#Mount the 70 lb angle bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends. Use a level to keep a level over the 20 feet.		#Mount the 70 lb angle bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends. Use a level to keep a level over the 20 feet.
	#Mount the 6x board first.		#Mount the 6x board first.
	#Mount the 8' plywood strip on back of the two 6" boards, on outside. Do not do this in situ. The ID piece of about 4' long will be cut to size later.		#Mount the 8' plywood strip on back of the two 6" boards, on outside. Do not do this in situ. The ID piece of about 4' long will be cut to size later.
			#Also mount the 12" connecting strip to one of the 6" boards.
	#Also mount the 13.75" strip of plywood on each side.		#Also mount the 13.75" strip of plywood on each side.
	#Join the two 10 foot sections by the back strip, cut to size. Move the shelf away from the glazing wall to screw in the connecting ~~pievlce~~.		#Join the two 10 foot sections by the back strip, cut to size, and by the mid connecting piece from the bottom using 1.5" screws - 2 on each side. Move the shelf away from the glazing wall to screw in the connecting piece.
			#Mount the 2x8 to the end strip on the side at the greenhouse corner. With this attached, the corner end can be shuffled to the corner, ready for attachment to the brackets.

Marcin at 01:36, 13 April 2016

2016-04-13T01:36:38Z

← Older revision		Revision as of 01:36, 13 April 2016
Line 1:		Line 1:
	#Mount the 70 lb ~~angke~~ bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends.		=20 Foot Shelves=
	#Mount the ~~6" piece~~ first.		These are made in two sections of 10' each.
	#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.		#Mount the 70 lb angle bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends. Use a level to keep a level over the 20 feet.
			#Mount the 6x board first.
			#Mount the 8' plywood strip on back of the two 6" boards, on outside. Do not do this in situ. The ID piece of about 4' long will be cut to size later.
			#Also mount the 13.75" strip of plywood on each side.
			#Join the two 10 foot sections by the back strip, cut to size. Move the shelf away from the glazing wall to screw in the connecting pievlce.

Marcin at 23:14, 12 April 2016

2016-04-12T23:14:40Z

← Older revision		Revision as of 23:14, 12 April 2016
Line 1:		Line 1:
	#Mount the 70 lb angke bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws.		#Mount the 70 lb angke bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws. Use two brackets every four feet with one bracket on the ends.
	#Mount the 6" piece first.		#Mount the 6" piece first.
	#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.		#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.

Marcin at 23:13, 12 April 2016

2016-04-12T23:13:06Z

← Older revision		Revision as of 23:13, 12 April 2016
Line 1:		Line 1:
	#Mount the 70 lb angke bracket, and the 1' long 2x4 after that.		#Mount the 70 lb angke bracket, and the 1' long 2x4 after that on top of the angle bracket using 1.5 " screws from the bottom. Mount the brackets with 2.5 or 3" screws.
	#Mount the 6" piece first.		#Mount the 6" piece first.
	#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.		#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.

Marcin at 23:11, 12 April 2016

2016-04-12T23:11:28Z

← Older revision		Revision as of 23:11, 12 April 2016
Line 1:		Line 1:
			#Mount the 70 lb angke bracket, and the 1' long 2x4 after that.
	#Mount the 6" piece first.		#Mount the 6" piece first.
	#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.		#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.

Marcin: Created page with "#Mount the 6" piece first. #Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later."

2016-04-12T23:09:20Z

Created page with "#Mount the 6" piece first. #Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later."

New page

#Mount the 6" piece first.
#Mount the 8' plywood strip on back of the two 6" boards, on outside. The ID piece of about 4' long will be cut to size later.