Shop Rules - Revision history

Greg Buckland: /* Safety */

2014-08-15T22:06:27Z

Safety

← Older revision		Revision as of 22:06, 15 August 2014
Line 5:		Line 5:
	*Loose clothing or jewelry are not permitted.		*Loose clothing or jewelry are not permitted.
	*Hearing protection and gloves must be worn when appropriate.		*Hearing protection and gloves must be worn when appropriate.
	*Gloves must ~~not~~ be worn when operating a spinning or turning machine.		*Gloves must NOT be worn when operating a spinning or turning machine.

	=Normal Operating Procedures=		=Normal Operating Procedures=

Greg Buckland: /* Safety */

2014-08-15T21:59:21Z

Safety

← Older revision		Revision as of 21:59, 15 August 2014
Line 1:		Line 1:
	=Safety=		=Safety=
	*Eye protection and ~~steel toed boots~~ must be worn at all times.		*Eye protection and closed-toe shoes must be worn at all times. Steel toed boots are strongly recommended.
	*~~Long~~ pants must be worn, no shorts.		*For welding and metalwork, long pants and long sleeves must be worn, no shorts.
	*~~No long hairs in the shop.~~ Long ~~hairs may get wrapped up in machinery~~ and ~~kill the longhair~~.		*Long hair must be tied back and secured, away from moving equipment.
	*Loose clothing ~~is not permitted for the same reason that longhairs aren't permitted.~~		*Loose clothing or jewelry are not permitted.
	*Long sleeves are ~~required when welding.~~
	*Loose jewelry is not permitted.
	*Hearing protection and gloves must be worn when appropriate.		*Hearing protection and gloves must be worn when appropriate.
	*Gloves must not be worn when operating a spinning or turning machine.		*Gloves must not be worn when operating a spinning or turning machine.

	=Normal Operating Procedures=		=Normal Operating Procedures=
	*No music or headphones in the shop		*No music or headphones in the shop

Marcin: /* End of Day */

2013-11-21T21:55:47Z

End of Day

← Older revision		Revision as of 21:55, 21 November 2013
Line 27:		Line 27:
	*Turn lights off and close garage doors at night. Garage doors help keep out moisture.		*Turn lights off and close garage doors at night. Garage doors help keep out moisture.
	*Wrap any loose welding wire cut ends so nobody trips on them.		*Wrap any loose welding wire cut ends so nobody trips on them.
	*Shut the ~~gas off~~		*Shut welding, torching, and any other gases off.
	*Sweep floor - 5 minutes		*Unplug the 2 gallong compressor.
			*Sweep floor - 5 minutes.

Marcin at 21:54, 21 November 2013

2013-11-21T21:54:27Z

@@ Line 1: / Line 1: @@
 =Normal Operating Procedures=
 *No music or headphones in the shop
@@ Line 20: / Line 29: @@
 *Shut the gas off
 *Sweep floor - 5 minutes

Marcin at 21:52, 21 November 2013

2013-11-21T21:52:16Z

← Older revision		Revision as of 21:52, 21 November 2013
Line 6:		Line 6:
	*Use 9" grinder for bulk grinding, and 4" grinder for detail grinding		*Use 9" grinder for bulk grinding, and 4" grinder for detail grinding
	*Only authorized users are allowed to operate machinery without supervision. See [[Authorized Users List]]		*Only authorized users are allowed to operate machinery without supervision. See [[Authorized Users List]]
	*		*Report all injuries to the individual in authority immediately, no matter how minor.
			*Do not leave operating machines unattended.
			*Do not try to stop the machine with your hands or body.
			*Always keep hands, hair feet, etc. clear of operating machinery.
			*Ensure tooling and work pieces are properly supported and clamped prior to operating a machine.
			*Do not machine heavy or unwieldy work pieces without special support structures.
			*Remove chuck keys, wrenches and other tools from machines after making adjustments.
			*Listen for abnormal sounds and report them.

	=End of Day=		=End of Day=

Marcin at 21:48, 21 November 2013

2013-11-21T21:48:49Z

← Older revision		Revision as of 21:48, 21 November 2013
Line 1:		Line 1:
			=Normal Operating Procedures=
			*No music or headphones in the shop
			*No alcohol or pets in the shop
			*No distracting chatter of tomfoolery
			*Turn off 3-phase generator when not in use
			*Use 9" grinder for bulk grinding, and 4" grinder for detail grinding
			*Only authorized users are allowed to operate machinery without supervision. See [[Authorized Users List]]
			*

	=End of Day=		=End of Day=
	*Turn lights off and close garage doors at night. Garage doors help keep out moisture.		*Turn lights off and close garage doors at night. Garage doors help keep out moisture.

Marcin: /* End of Day */

2013-11-21T21:46:13Z

End of Day

← Older revision		Revision as of 21:46, 21 November 2013
Line 2:		Line 2:
	*Turn lights off and close garage doors at night. Garage doors help keep out moisture.		*Turn lights off and close garage doors at night. Garage doors help keep out moisture.
	*Wrap any loose welding wire cut ends so nobody trips on them.		*Wrap any loose welding wire cut ends so nobody trips on them.
			*Shut the gas off
			*Sweep floor - 5 minutes

	=Clothing=		=Clothing=

Marcin at 21:45, 21 November 2013

2013-11-21T21:45:27Z

← Older revision		Revision as of 21:45, 21 November 2013
Line 1:		Line 1:
			=End of Day=
	*Turn lights off and close garage doors at night. Garage doors help keep out moisture.		*Turn lights off and close garage doors at night. Garage doors help keep out moisture.
	*Wrap any loose welding wire cut ends so nobody trips on them.		*Wrap any loose welding wire cut ends so nobody trips on them.

			=Clothing=
			*Steel toes boots must be worn
			*Long pants must be worn, no shorts.
	*No long hairs in the shop. Long hairs may get wrapped up in machinery and kill the longhair.		*No long hairs in the shop. Long hairs may get wrapped up in machinery and kill the longhair.
	*Loose clothing is not permitted for the same reason that longhairs aren't permitted.		*Loose clothing is not permitted for the same reason that longhairs aren't permitted.
	*Long sleeves are required when welding.		*Long sleeves are required when welding.
	*Loose jewelry is not permitted.		*Loose jewelry is not permitted.
	~~Long hair must be pulled back to avoid entanglement with operating machinery.~~

Marcin at 21:44, 21 November 2013

2013-11-21T21:44:03Z

← Older revision		Revision as of 21:44, 21 November 2013
Line 2:		Line 2:
	*Wrap any loose welding wire cut ends so nobody trips on them.		*Wrap any loose welding wire cut ends so nobody trips on them.
	*No long hairs in the shop. Long hairs may get wrapped up in machinery and kill the longhair.		*No long hairs in the shop. Long hairs may get wrapped up in machinery and kill the longhair.
	*		*Loose clothing is not permitted for the same reason that longhairs aren't permitted.
			*Long sleeves are required when welding.
			*Loose jewelry is not permitted.
			Long hair must be pulled back to avoid entanglement with operating machinery.

Marcin: Created page with "Turn lights off and close garage doors at night. Garage doors help keep out moisture. Wrap any loose welding wire cut ends so nobody trips on them. *No long hairs in the sho..."

2013-11-21T21:41:07Z

Created page with "*Turn lights off and close garage doors at night. Garage doors help keep out moisture. *Wrap any loose welding wire cut ends so nobody trips on them. *No long hairs in the sho..."

New page

*Turn lights off and close garage doors at night. Garage doors help keep out moisture.
*Wrap any loose welding wire cut ends so nobody trips on them.
*No long hairs in the shop. Long hairs may get wrapped up in machinery and kill the longhair.
*

Shop Rules - Revision history

Greg Buckland: /* Safety */

Greg Buckland: /* Safety */

Marcin: /* End of Day */

Marcin at 21:54, 21 November 2013

Marcin at 21:52, 21 November 2013

Marcin at 21:48, 21 November 2013

Marcin: /* End of Day */

Marcin at 21:45, 21 November 2013

Marcin at 21:44, 21 November 2013

Marcin: Created page with "*Turn lights off and close garage doors at night. Garage doors help keep out moisture. *Wrap any loose welding wire cut ends so nobody trips on them. *No long hairs in the sho..."

Marcin: Created page with "Turn lights off and close garage doors at night. Garage doors help keep out moisture. Wrap any loose welding wire cut ends so nobody trips on them. *No long hairs in the sho..."