Terminal Case CNC 1 - Revision history

YK: /* Steps */

2012-11-04T06:26:43Z

Steps

← Older revision		Revision as of 06:26, 4 November 2012
Line 12:		Line 12:

	Overall case dimensions: 3.5" H x 12" W x 18"		Overall case dimensions: 3.5" H x 12" W x 18"

			Cut plate in half for two 18" lengths

			Cut bar to two 18" lengths and two 11" lengths

	[[Image: terminalcasev3welded.jpg\|100px]]		[[Image: terminalcasev3welded.jpg\|100px]]

YK: /* Steps */

2012-11-03T23:00:09Z

Steps

← Older revision		Revision as of 23:00, 3 November 2012
Line 12:		Line 12:

	Overall case dimensions: 3.5" H x 12" W x 18"		Overall case dimensions: 3.5" H x 12" W x 18"

			[[Image: terminalcasev3welded.jpg\|100px]]

	=Old Steps=		=Old Steps=

YK: /* Steps */

2012-11-02T20:31:37Z

Steps

← Older revision		Revision as of 20:31, 2 November 2012
Line 11:		Line 11:
	=Steps=		=Steps=

	Overall case dimensions: 3.5" H x 12" W x 14"		Overall case dimensions: 3.5" H x 12" W x 18"

	=Old Steps=		=Old Steps=

YK at 20:25, 2 November 2012

2012-11-02T20:25:37Z

← Older revision		Revision as of 20:25, 2 November 2012
Line 10:		Line 10:

	=Steps=		=Steps=

			Overall case dimensions: 3.5" H x 12" W x 14"

			=Old Steps=

	Organize the materials		Organize the materials

YK: /* Steps */

2012-10-15T06:31:00Z

Steps

← Older revision		Revision as of 06:31, 15 October 2012
Line 28:		Line 28:

	Position and bend the rubber inside the case. Then, move one side of the plastic plate into the rubber, then press down the other end of the plastic plate in order to mount the plastic plate inside the box.		Position and bend the rubber inside the case. Then, move one side of the plastic plate into the rubber, then press down the other end of the plastic plate in order to mount the plastic plate inside the box.

			[[File: case1bendrubber.jpg\|200x200px]] [[File: case1plasticstart.jpg\|200x200px]] [[File: case1plasticdown.jpg\|200x200px]]

YK at 06:29, 15 October 2012

2012-10-15T06:29:18Z

← Older revision		Revision as of 06:29, 15 October 2012
Line 9:		Line 9:
	[http://www.amazonsupply.com/dp/B000ILHW9I/ref=sp_dp_g2c_asin HDPE Plate 1/4" x 12" x 24"]		[http://www.amazonsupply.com/dp/B000ILHW9I/ref=sp_dp_g2c_asin HDPE Plate 1/4" x 12" x 24"]

	=		=Steps=

			Organize the materials

			[[File: case1mats.jpg\|200x200px]]

			Cut the aluminum plate to 14" x2 lengths. Cut the bar to 13" x2 and 12" x2 lengths. Cut the rubber to 0.5" length. Cut the plastic plate to 13" length by 10.5" width (make it smaller than bigger)

			[[File: case1aplate.jpg\|200x200px]] [[File: case1bar.jpg\|200x200px]] [[File: case1rubber.jpg\|200x200px]] [[File: case1pplate.jpg\|200x200px]]

			Position, tack weld, and weld the bars onto the aluminum plate to form an open aluminum box.

			[[File: case1position.jpg\|200x200px]] [[File: case1tackweld.jpg\|200x200px]] [[File: case1weld.jpg\|200x200px]]

			Drill the bars to make holes for cables and wires.

			[[File: case1drillbars.jpg\|200x200px]]

			Position and bend the rubber inside the case. Then, move one side of the plastic plate into the rubber, then press down the other end of the plastic plate in order to mount the plastic plate inside the box.

YK: Created page with "=Materials= [https://www.amazonsupply.com/dp/B003U6HU9U/ref=sp_dp_g2c_asin Aluminum Plate 1/4" x 12" x 36"] [https://www.amazonsupply.com/dp/B003U6HWI4/ref=sp_dp_g2c_asin Alumi..."

2012-10-15T06:01:41Z

Created page with "=Materials= [https://www.amazonsupply.com/dp/B003U6HU9U/ref=sp_dp_g2c_asin Aluminum Plate 1/4" x 12" x 36"] [https://www.amazonsupply.com/dp/B003U6HWI4/ref=sp_dp_g2c_asin Alumi..."

New page

=Materials=

[https://www.amazonsupply.com/dp/B003U6HU9U/ref=sp_dp_g2c_asin Aluminum Plate 1/4" x 12" x 36"]

[https://www.amazonsupply.com/dp/B003U6HWI4/ref=sp_dp_g2c_asin Aluminum Bar 1/2" x 3" x 72"]

[http://www.amazonsupply.com/dp/B000MAMG2I/ref=sp_dp_g2c_asin Pure Tan Gum Rubber 1/8" x 12" x 24"]

[http://www.amazonsupply.com/dp/B000ILHW9I/ref=sp_dp_g2c_asin HDPE Plate 1/4" x 12" x 24"]

=