Tooling Plate - Revision history

YK: /* Materials */

2012-12-01T00:47:11Z

Materials

2012-12-01T00:44:38Z

Materials

2012-12-01T00:21:00Z

Build

← Older revision		Revision as of 00:21, 1 December 2012
Line 63:		Line 63:
	----		----

	Use T-slot cutter on mill. (31/32" Cutter Dia, 25/64" W Face)		Use T-slot cutter on mill. (25/32" Cutter Dia, 21/64" W Face)

	Match or be a bit less than the depth of the slot; firmly lock the height for this entire step; 80rpm used.		Match or be a bit less than the depth of the slot; firmly lock the height for this entire step; 80rpm used.

2012-12-01T00:20:28Z

Build

← Older revision		Revision as of 00:20, 1 December 2012
Line 23:		Line 23:
	=Build=		=Build=

	Start with ~~1.25" x 6.25" x 12" cast~~ grey iron plate		Start with the grey iron plate.

	[[File: greyironplate.jpg\|200px]]		[[File: greyironplate.jpg\|200px]]

2012-12-01T00:11:27Z

Materials

← Older revision		Revision as of 00:11, 1 December 2012
Line 19:		Line 19:
	=Materials=		=Materials=

	[[Grey Iron]] - 1.25" x 6.25" x 12" - ~~[[Mcmaster Carr]] 8923K671 OR~~ [[Speedymetals]]		[[Grey Iron]] - 1.25" x 4.25" x 12" - [[Speedymetals]]

	=Build=		=Build=

2012-11-30T23:49:23Z

Tools

← Older revision		Revision as of 23:49, 30 November 2012
Line 15:		Line 15:
	[[Roughing Endmill]] - 1/2" dia - [[Mcmaster Carr]] 8817A52		[[Roughing Endmill]] - 1/2" dia - [[Mcmaster Carr]] 8817A52

	[[T-slot Cutter]] - ~~for 1/2" bolts~~ - [[Mcmaster Carr]] ~~8789A12~~		[[T-slot Cutter]] - 19.8mm dia - [[Mcmaster Carr]] 8789A11

	=Materials=		=Materials=

2012-11-16T19:15:05Z

Build

← Older revision		Revision as of 19:15, 16 November 2012
Line 29:		Line 29:
	----		----

	Use [[Roughing Endmill]] on [[Mill]] (1/2" dia 4 flute); even out the top and bottom surfaces; firmly lock the height for this entire step.		Use [[Roughing Endmill]] on [[Mill]] (1/2" dia 4 flute); even out the top and bottom surfaces; firmly lock the height for this entire step; 330rpm used.

	[[File: roughplaningironplate.jpg\|200px]]		[[File: roughplaningironplate.jpg\|200px]]

2012-11-16T19:14:51Z

Build

← Older revision		Revision as of 19:14, 16 November 2012
Line 56:		Line 56:
	----		----

	Use [[Roughing Endmill]] on [[Mill]] (1/2" dia 4 flute); make slots; firmly lock the height for this entire step.		Use [[Roughing Endmill]] on [[Mill]] (1/2" dia 4 flute); make slots; firmly lock the height for this entire step; 330rpm used.

	[[File: roughingendmill.jpg\|200px]]		[[File: roughingendmill.jpg\|200px]]
Line 65:		Line 65:
	Use T-slot cutter on mill. (31/32" Cutter Dia, 25/64" W Face)		Use T-slot cutter on mill. (31/32" Cutter Dia, 25/64" W Face)

	Match or be a bit less than the depth of the slot; firmly lock the height for this entire step.		Match or be a bit less than the depth of the slot; firmly lock the height for this entire step; 80rpm used.

	[[File: tslotcutter.jpg\|200px]]		[[File: tslotcutter.jpg\|200px]]

2012-11-16T19:13:30Z

Build

2012-11-16T19:11:07Z

Build

← Older revision		Revision as of 19:11, 16 November 2012
Line 67:		Line 67:
	Match or be a bit less than the depth of the slot; firmly lock the height for this entire step.		Match or be a bit less than the depth of the slot; firmly lock the height for this entire step.

	[[File: ~~tslottedgreyironplate~~.jpg\|200px]]		[[File: tslotcutter.jpg\|200px]]

	----		----

	Drill? Tap?		Drill? Tap?