Torch Table Zaxis - Revision history

Conor at 18:39, 9 February 2011

2011-02-09T18:39:30Z

← Older revision		Revision as of 18:39, 9 February 2011
Line 1:		Line 1:
			{{Category=Torch Table}}
	=Bill of Materials=		=Bill of Materials=
	{\|border="1" {{table}}		{\|border="1" {{table}}
Line 154:		Line 155:
	\|----		\|----
	\|}		\|}

	~~[[Category:CAD]]~~
	~~[[Category:Digital Fabrication]]~~

Rasmus at 12:22, 4 January 2011

2011-01-04T12:22:40Z

← Older revision		Revision as of 12:22, 4 January 2011
Line 154:		Line 154:
	\|----		\|----
	\|}		\|}

			[[Category:CAD]]
			[[Category:Digital Fabrication]]

Lawrence: /* Bill of Materials */

2009-08-31T23:45:55Z

Bill of Materials

Show changes

Lawrence: /* Bill of Materials */

2009-08-31T16:17:40Z

Bill of Materials

← Older revision		Revision as of 16:17, 31 August 2009
Line 1:		Line 1:
	=Bill of Materials=		=Bill of Materials=
	Item Discription Amount Cost per item Further Info Purpose Aquired?		{\| {{table}}
	Bearing R6-2RS 3/8"x7/8"x9/32" Sealed 10 pack 0 $14.95 VXB Part Number: Kit711 For preventing the carrage from jumping the track no		\| align="center" style="background:#f0f0f0;"\|'''Item'''
	V-Groove Bearings 3/8 inch single pack 4 9.95 VXB V-Groove bearings Part number: Kit8407 To provide low friction linear motion no		\| align="center" style="background:#f0f0f0;"\|'''Discription'''
	3/8 inch Hard Fiber Washers Pack of 100 8 2.5 McMaster Part Number: 95601A330 Holding bearings no		\| align="center" style="background:#f0f0f0;"\|'''Amount'''
	Hot rolled steel 3"x1/8" plate 10.~~0 Ft~~. 1.~~083333333~~ 12.7 Metalsdepot To provide material for motor mounts no		\| align="center" style="background:#f0f0f0;"\|'''Cost per item'''
	Hot rolled steel 1"x1" square tubes 16 gauge 24ft for $23.28 16 23.28 Metalsdepot To provide structural support no		\| align="center" style="background:#f0f0f0;"\|'''Further Info'''
	Gear Rack (1/2” sq. x 72” 20 DP 20 Deg) 6 feet per rack 1.~~333333333~~ 24.8 Standard Steel Specialty Part Number: 200011 rack for gear to ride on no		\| align="center" style="background:#f0f0f0;"\|'''Purpose'''
	3 x 1/8 inch cold rolled Plate 6.~~0 Ft. 1~~.~~333333333~~ 17.28 Metalsdepot To provide material to make rails no		\| align="center" style="background:#f0f0f0;"\|'''Aquired?'''
	"3/8 inch threaded rod, Overall Length		\|-
	36""" ~~Each 22~~.8 $2 McMaster Part Number: 98837A031 for connecting the top and bottom carage no		\| Bearing R6-2RS 3/8\"x7/8\"x9/32\" Sealed\|\|10 pack\|\|4\|\|$14.95 \|\|VXB Part Number: Kit711\|\|For preventing the carrage from jumping the track\|\|no
	3/8 inch nuts Pack of 100 16 4.2 Part Number: 90473A031 For locking threaded rod in place no		\|-
	3/8 inch washers Pack of 140 16 3.23 Part Number: 90126A031 For locking nuts and for spacers no		\| V-Groove Bearings 3/8 inch\|\|single pack\|\|4\|\|9.95\|\|VXB V-Groove bearings Part number: Kit8407\|\|To provide low friction linear motion\|\|no
	Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Dia, 1/2" Bore Each 1 15.37 McMaster Part Number: 5172T12 Attaches to stepper motors and interfaces with gear rack no		\|-
	sleeve bearing Each 1 1.34 McMaster Part Number: 6391K143 to connect between the stepper motor and the gear, will also add a bit of adjustable length no		\| 3/8 inch Hard Fiber Washers\|\|Pack of 100\|\|16\|\|2.5\|\|McMaster Part Number: 95601A330\|\|Holding bearings\|\|no
	10-32 set screw 7/16" per Pack of 100 1 5.44 Part Number: 92311A428 Set screw for attaching spur gear, sleeve bearing to stepper shaft no		\|-
	10 gauge bolts Pack of 50 6 7.78 McMaster Part Number: 92610A245 stepper no		\| Hot rolled steel 3\"x1/8\" plate\|\|10.0 Ft.\|\|16.75\|\|12.7\|\|Metalsdepot\|\|To provide material for motor mounts\|\|no
	10 gauge nuts Pack of 100 6 1.54 McMaster Part Number: 90480A011 stepper no		\|-
	Zinc-Pltd Stl Pan Head Phillips Machine Screw 1/4"-20 Thread, 1-1/2" Length Pack of 100 4 10.75 McMaster Part Number: ~~90272A546~~ Connects the mount plate arms to the carrage no		\| Hot rolled steel 1\"x1\" square tubes 16 gauge\|\|24ft for $23.28\|\|66\|\|23.28\|\|Metalsdepot\|\|To provide structural support\|\|no
	Zinc & Yellow Plated Grade 8 Steel Hex Nut 1/4"-20 Thread Size, 7/16" Width, 7/32" Height Packs of 100 16 3.06 McMaster Part Number: 94895A029 For locking the mount plate swing tightness no		\|-
	1/4 inch Nylon Thrust Bearing Each 4 1.05 McMaster Part Number: 2797T1 allows the motor to swing freely no		\| Gear Rack (1/2” sq. x 72” 20 DP 20 Deg)\|\|6 feet per rack\|\|5.5\|\|24.8\|\|Standard Steel Specialty Part Number: 200011\|\|rack for gear to ride on\|\|no
	stepper spring pack of 6 1 10 McMaster Part Number: 3114T79 Prevents stepper motor shaft from crunching no		\|-
			\| 3 x 1/8 inch cold rolled Plate\|\|6.0 Ft.\|\|11\|\|17.28\|\|Metalsdepot\|\|To provide material to make rails\|\|no
			\|-
			\| \"3/8 inch threaded rod, Overall Length
			\|-
			\| 36\"\"\"\|\| Each\|\|57.2\|\|$2 \|\|McMaster Part Number: 98837A031\|\|for connecting the top and bottom carage\|\|no
			\|-
			\| 3/8 inch nuts\|\|Pack of 100\|\|48\|\|4.2\|\|Part Number: 90473A031\|\|For locking threaded rod in place\|\|no
			\|-
			\| 3/8 inch washers\|\|Pack of 140\|\|48\|\|3.23\|\|Part Number: 90126A031\|\|For locking nuts and for spacers\|\|no
			\|-
			\| Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1\" Pitch Dia, 1/2\" Bore\|\|Each\|\|1\|\|15.37\|\|McMaster Part Number: 5172T12\|\|Attaches to stepper motors and interfaces with gear rack\|\|no
			\|-
			\| sleeve bearing\|\|Each\|\|1\|\|1.34\|\|McMaster Part Number: 6391K143\|\|to connect between the stepper motor and the gear, will also add a bit of adjustable length\|\|no
			\|-
			\| 10-32 set screw 7/16\"\|\|per Pack of 100\|\|1\|\|5.44\|\|Part Number: 92311A428\|\|Set screw for attaching spur gear, sleeve bearing to stepper shaft\|\|no
			\|-
			\| 10 gauge bolts\|\| Pack of 50\|\|34\|\|7.78\|\|McMaster Part Number: 92610A245\|\|stepper\|\|no
			\|-
			\| 10 gauge nuts\|\|Pack of 100\|\|40\|\|1.54\|\|McMaster Part Number: 90480A011\|\|stepper\|\|no
			\|-
			\| Zinc-Pltd Stl Pan Head Phillips Machine Screw 1/4\"-20 Thread, 1-1/2\" Length\|\|Pack of 100\|\|4\|\|10.75\|\|McMaster Part Number: 90272A546\|\|Connects the mount plate arms to the carrage\|\|no
			\|-
			\| Zinc & Yellow Plated Grade 8 Steel Hex Nut 1/4\"-20 Thread Size, 7/16\" Width, 7/32\" Height\|\|Packs of 100\|\|8\|\|3.06\|\|McMaster Part Number: 94895A029\|\|For locking the mount plate swing tightness\|\|no
			\|-
			\| 1/4 inch Nylon Thrust Bearing\|\|Each\|\|4\|\|1.05\|\|McMaster Part Number: 2797T1\|\|allows the motor to swing freely\|\|no
			\|-
			\| stepper spring\|\|pack of 6\|\|1\|\|10\|\|McMaster Part Number: 3114T79\|\|Prevents stepper motor shaft from crunching \|\|no
			\|-
			\|
			\|}

Lawrence at 16:16, 31 August 2009

2009-08-31T16:16:56Z

Show changes

Lawrence: Created page with '=Bill of Materials= Bill of Materials 5172T12$2.50 per Pack {| border="1" !Item !Number !Cost !Further Info !Purpose !Aquired? |- |V-Groove Bearings 3/...'

2009-08-29T22:27:57Z

Created page with '=Bill of Materials= Bill of Materials 5172T12$2.50 per Pack {| border="1" !Item !Number !Cost !Further Info !Purpose !Aquired? |- |V-Groove Bearings 3/...'

New page

=Bill of Materials=
[[Torch_Table_BoM | Bill of Materials]]
5172T12$2.50 per Pack
{| border="1"
!Item
!Number
!Cost
!Further Info
!Purpose
!Aquired?
|-
|V-Groove Bearings 3/8 inch
|4
|$9.95 Each, Total $39.80
|[http://www.vxb.com/page/bearings/CTGY/V-Groove-Bearings VXB V-Groove bearings]
|To provide low friction linear motion and to constrain motion in the y axis
|no
|-
|Hot rolled steel 3"x1/8" plate
|1 feet
|$10.00 for 4' $10.00 Total
|[http://www.metalsdepot.com/ Metalsdepot]
|To provide material for stepper motor mount plates, stepper swing arms, and cross beam support
|no
|-
|Hot rolled steel 1"x1" square tubes 16 gauge
|2 feet
|
|[http://www.metalsdepot.com/ Metalsdepot]
|To provide structural support
|no
|-
|200011 (1/2” sq. x 72” 20 DP 20 Deg) rack
|2' length so 1 rack
|$24.80
|[http://www.stdsteel.com/ Standard Steel Specialty]
|rack for gear to ride on
|yes
|-
|3 x 1/8 inch cold rolled Plate
|2 feet
|
|[http://www.metalsdepot.com/ Metalsdepot]
|To provide material to make rails
|no
|-
|threaded 3/8 inch rod
|2 feet
|
|[http://www.mcmaster.com/ McMaster]
|For attaching V-Groove Bearings, Ball Bearings, and connecting the top/bottom carage
|no
|-
|3/8 inch nuts
|50
|
|Part Number: 90473A031
|For locking threaded rod in place
|no
|-
|3/8 inch washers
|40
|
|Part Number: 90126A031
|For locking nuts and for spacers
|no
|-
|Steel Plain Bore 14-1/2 Deg Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Diameter, |3/8" Bore
|1
|$15.37 Each
|[http://www.mcmaster.com/ McMaster] 5172T12, 1327K113, Part Number: 5912K12, 6412K11
|Attaches to stepper motors and interfaces with gear rack
|no
|-
|Thrust Bearing
|4
|
|[http://www.mcmaster.com/ McMaster] Nylon Part Number: 2797T1
|allows the motor to swing freely
|no
|-
|sleeve bearing
|1
|$1.34 each
|[http://www.mcmaster.com/ McMaster] Part Number: 6391K143
|to connect between the stepper motor and the gear, will also add a bit of adjustable length
|no
|-
|10 gauge bolts
|30
| $7.78 per Pack of 50
|[http://www.mcmaster.com/ McMaster] Part Number: 92610A245
|stepper
|no
|-
|10 gauge nuts
|30
| $1.54 per Pack of 100
|[http://www.mcmaster.com/ McMaster] Part Number: 90480A011
|stepper
|no
|-
|Hard Fiber Washer
|8
|$2.50 per Pack
|[http://www.mcmaster.com/ McMaster] Part Number: 95601A330
|Holding bearings
|no
|-
|stepper saftey spring
|1
|$10.00 per Pack of 6
|[http://www.mcmaster.com/ McMaster] Part Number: 3114T79
|
|no
|}