https://wiki.opensourceecology.org/index.php?action=history&feed=atom&title=Typical_Profile_File_for_v19.06 2026-04-12T09:56:08Z Revision history for this page on the wiki MediaWiki 1.39.13 https://wiki.opensourceecology.org/index.php?title=Typical_Profile_File_for_v19.06&diff=202937&oldid=prev 2019-11-07T01:35:46Z

<p>Created page with &quot;[profile] layer_height = .31 wall_thickness = 0.8 retraction_enable = True solid_layer_thickness = 0.8 fill_density = 20 perimeter_before_infill = True nozzle_size = 0.4 print...&quot;</p> <p><b>New page</b></p><div>[profile]<br /> layer_height = .31<br /> wall_thickness = 0.8<br /> retraction_enable = True<br /> solid_layer_thickness = 0.8<br /> fill_density = 20<br /> perimeter_before_infill = True<br /> nozzle_size = 0.4<br /> print_speed = 50<br /> print_temperature = 230<br /> print_temperature2 = 0<br /> print_temperature3 = 0<br /> print_temperature4 = 0<br /> print_temperature5 = 0<br /> print_bed_temperature = 80<br /> support = None<br /> platform_adhesion = None<br /> support_dual_extrusion = Both<br /> wipe_tower = False<br /> wipe_tower_volume = 15<br /> ooze_shield = False<br /> filament_diameter = 2.85<br /> filament_diameter2 = 0<br /> filament_diameter3 = 0<br /> filament_diameter4 = 0<br /> filament_diameter5 = 0<br /> filament_flow = 100.0<br /> retraction_speed = 40.0<br /> retraction_amount = 2.5<br /> retraction_dual_amount = 16.5<br /> retraction_min_travel = 1.5<br /> retraction_combing = All<br /> retraction_minimal_extrusion = 0.02<br /> retraction_hop = 0.0<br /> bottom_thickness = 0.3<br /> layer0_width_factor = 100<br /> object_sink = 0<br /> overlap_dual = 0.15<br /> travel_speed = 50<br /> bottom_layer_speed = 25<br /> infill_speed = 50<br /> solidarea_speed = 25<br /> inset0_speed = 25<br /> insetx_speed = 25<br /> cool_min_layer_time = 10<br /> fan_enabled = True<br /> skirt_line_count = 3<br /> skirt_gap = 3.0<br /> skirt_minimal_length = 150.0<br /> fan_full_height = 1.0<br /> fan_speed = 100<br /> fan_speed_max = 100<br /> cool_min_feedrate = 10<br /> cool_head_lift = False<br /> solid_top = True<br /> solid_bottom = True<br /> fill_overlap = 15<br /> support_type = Lines<br /> support_angle = 60<br /> support_fill_rate = 15<br /> support_xy_distance = 0.7<br /> support_z_distance = 0.15<br /> spiralize = False<br /> simple_mode = False<br /> brim_line_count = 10<br /> raft_margin = 5.0<br /> raft_line_spacing = 3.0<br /> raft_base_thickness = 0.3<br /> raft_base_linewidth = 1.0<br /> raft_interface_thickness = 0.27<br /> raft_interface_linewidth = 0.4<br /> raft_airgap_all = 0.0<br /> raft_airgap = 0.22<br /> raft_surface_layers = 2<br /> raft_surface_thickness = 0.27<br /> raft_surface_linewidth = 0.4<br /> fix_horrible_union_all_type_a = True<br /> fix_horrible_union_all_type_b = False<br /> fix_horrible_use_open_bits = False<br /> fix_horrible_extensive_stitching = False<br /> plugin_config = <br /> object_center_x = -1<br /> object_center_y = -1<br /> simplemodesettings = <br /> simplemodeprofile = Standard<br /> simplemodematerial = PLA<br /> simplemodematerialtype = Beginner<br /> <br /> [alterations]<br /> start.gcode = ;M92 E408<br /> M92 E425<br /> M203 Z10 ; override max Z feedrate from 5 to 10 mm/s<br /> G28 X0 Y0 ; home<br /> ;G0 X40 ;<br /> G0 Y40 ; move over<br /> G28 Z0<br /> G29 ; autolevel - needs to be over +20 x<br /> G90 ; set absolute coordinates<br /> G92 E0<br /> ;M851 Z-2 ; Set the Z probe offset to -2<br /> end.gcode = <br /> G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way<br /> M104 S0 ; make sure the extuder is turned off.<br /> M140 S0 ; make sure the bed is turned off.<br /> G0 Z330 ; take bed back down<br /> M84 ;steppers off<br /> ;{profile_string}<br /> start2.gcode = ;Sliced at: {day} {date} {time}<br /> ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}<br /> ;Print time: {print_time}<br /> ;Filament used: {filament_amount}m {filament_weight}g<br /> ;Filament cost: {filament_cost}<br /> ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line<br /> ;M104 S{print_temperature} ;Uncomment to add your own temperature line<br /> ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line<br /> ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line<br /> G21 ;metric values<br /> G90 ;absolute positioning<br /> M107 ;start with the fan off<br /> G28 X0 Y0 ;move X/Y to min endstops<br /> G28 Z0 ;move Z to min endstops<br /> G1 Z15.0 F{travel_speed} ;move the platform down 15mm<br /> T1 ;Switch to the 2nd extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F200 E-{retraction_dual_amount}<br /> T0 ;Switch to the first extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F{travel_speed}<br /> ;Put printing message on LCD screen<br /> M117 Printing...<br /> end2.gcode = ;End GCode<br /> M104 T0 S0 ;extruder heater off<br /> M104 T1 S0 ;extruder heater off<br /> M140 S0 ;heated bed heater off (if you have it)<br /> G91 ;relative positioning<br /> G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure<br /> G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more<br /> G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way<br /> M84 ;steppers off<br /> G90 ;absolute positioning<br /> ;{profile_string}<br /> start3.gcode = ;Sliced at: {day} {date} {time}<br /> ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}<br /> ;Print time: {print_time}<br /> ;Filament used: {filament_amount}m {filament_weight}g<br /> ;Filament cost: {filament_cost}<br /> ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line<br /> ;M104 S{print_temperature} ;Uncomment to add your own temperature line<br /> ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line<br /> ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line<br /> G21 ;metric values<br /> G90 ;absolute positioning<br /> M107 ;start with the fan off<br /> G28 X0 Y0 ;move X/Y to min endstops<br /> G28 Z0 ;move Z to min endstops<br /> G1 Z15.0 F{travel_speed} ;move the platform down 15mm<br /> T2 ;Switch to the 2nd extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F200 E-{retraction_dual_amount}<br /> T1 ;Switch to the 2nd extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F200 E-{retraction_dual_amount}<br /> T0 ;Switch to the first extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F{travel_speed}<br /> ;Put printing message on LCD screen<br /> M117 Printing...<br /> end3.gcode = ;End GCode<br /> M104 T0 S0 ;extruder heater off<br /> M104 T1 S0 ;extruder heater off<br /> M104 T2 S0 ;extruder heater off<br /> M140 S0 ;heated bed heater off (if you have it)<br /> G91 ;relative positioning<br /> G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure<br /> G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more<br /> G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way<br /> M84 ;steppers off<br /> G90 ;absolute positioning<br /> ;{profile_string}<br /> start4.gcode = ;Sliced at: {day} {date} {time}<br /> ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}<br /> ;Print time: {print_time}<br /> ;Filament used: {filament_amount}m {filament_weight}g<br /> ;Filament cost: {filament_cost}<br /> ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line<br /> ;M104 S{print_temperature} ;Uncomment to add your own temperature line<br /> ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line<br /> ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line<br /> ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line<br /> G21 ;metric values<br /> G90 ;absolute positioning<br /> M107 ;start with the fan off<br /> G28 X0 Y0 ;move X/Y to min endstops<br /> G28 Z0 ;move Z to min endstops<br /> G1 Z15.0 F{travel_speed} ;move the platform down 15mm<br /> T3 ;Switch to the 4th extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F200 E-{retraction_dual_amount}<br /> T2 ;Switch to the 3th extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F200 E-{retraction_dual_amount}<br /> T1 ;Switch to the 2nd extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F200 E-{retraction_dual_amount}<br /> T0 ;Switch to the first extruder<br /> G92 E0 ;zero the extruded length<br /> G1 F200 E10 ;extrude 10mm of feed stock<br /> G92 E0 ;zero the extruded length again<br /> G1 F{travel_speed}<br /> ;Put printing message on LCD screen<br /> M117 Printing...<br /> end4.gcode = ;End GCode<br /> M104 T0 S0 ;extruder heater off<br /> M104 T1 S0 ;extruder heater off<br /> M104 T2 S0 ;extruder heater off<br /> M104 T3 S0 ;extruder heater off<br /> M140 S0 ;heated bed heater off (if you have it)<br /> G91 ;relative positioning<br /> G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure<br /> G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more<br /> G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way<br /> M84 ;steppers off<br /> G90 ;absolute positioning<br /> ;{profile_string}<br /> support_start.gcode = <br /> support_end.gcode = <br /> cool_start.gcode = <br /> cool_end.gcode = <br /> replace.csv = <br /> preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.<br /> ;This code is added before the T(n)<br /> postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.<br /> ;This code is added after the T(n)</div>

Marcin