User:Dorkmo/Builds/CircularKnitic-Sock - Revision history

Dorkmo: /* Overview */

2019-04-20T15:12:51Z

Overview

← Older revision		Revision as of 15:12, 20 April 2019
Line 5:		Line 5:

	https://github.com/OpenSourceEcology/circular_knitic/tree/master/SCAD/Build-20190331-socktest		https://github.com/OpenSourceEcology/circular_knitic/tree/master/SCAD/Build-20190331-socktest

			[[OSE_CircularKnitic_v18.03#CKvarProfile-SockTest201904.scad]]

	=BOM=		=BOM=

2019-04-20T14:50:30Z

← Older revision		Revision as of 14:50, 20 April 2019
Line 1:		Line 1:
			[[Image:CK Sock Test 1904 First Run.jpeg\|thumb\|right\|150px]]
	=Overview=		=Overview=

2019-04-20T14:38:03Z

April 20, 2019

← Older revision		Revision as of 14:38, 20 April 2019
Line 20:		Line 20:
	**need to figure out how to do micro stepping on drivers		**need to figure out how to do micro stepping on drivers
	***lots of skipped steps and hang ups		***lots of skipped steps and hang ups
			**still seems to be a diver overheating problem, will get heatsink and fan
			***hang ups increasing with run time/temperature it seems
	**seems there are a few needles that dont want to slide easily		**seems there are a few needles that dont want to slide easily
	***need to disassemble and diagnose - sand paper on p2 inserts?		***need to disassemble and diagnose - sand paper on p2 inserts?

2019-04-20T14:35:05Z

April 20, 2019

← Older revision		Revision as of 14:35, 20 April 2019
Line 26:		Line 26:
	**smaller space between needles seems to be okay, no apparent problems		**smaller space between needles seems to be okay, no apparent problems
	***UPneedle2needle=9.12985;		***UPneedle2needle=9.12985;


	<html><iframe width="560" height="315" src="https://www.youtube.com/embed/y_F94h-HLos" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>		<html><iframe width="560" height="315" src="https://www.youtube.com/embed/y_F94h-HLos" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

2019-04-20T14:34:51Z

April 20, 2019

← Older revision		Revision as of 14:34, 20 April 2019
Line 24:		Line 24:
	***causing motors to hang up especially bad in certain spots		***causing motors to hang up especially bad in certain spots
	***they dont seem to hang up as bad when machine is spinning ccw, not sure why?		***they dont seem to hang up as bad when machine is spinning ccw, not sure why?
			**smaller space between needles seems to be okay, no apparent problems
			***UPneedle2needle=9.12985;

	<html><iframe width="560" height="315" src="https://www.youtube.com/embed/y_F94h-HLos" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>		<html><iframe width="560" height="315" src="https://www.youtube.com/embed/y_F94h-HLos" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

2019-04-20T14:31:05Z

April 19, 2019

← Older revision		Revision as of 14:31, 20 April 2019
Line 39:		Line 39:
	***have to remove needles or disassemble plates		***have to remove needles or disassemble plates
	**claws on p4 yarn holder have holes that are relatively too big		**claws on p4 yarn holder have holes that are relatively too big
	***~~bottom side~~ is snapping off on the outer hole		***lower half is snapping off below the outer hole
			***could make smaller holes? or remove outer hole, bolt only through inner side?
	**aluminum angle iron holder needs some tweaking		**aluminum angle iron holder needs some tweaking
	***when tightened all the way, begins to expand and let go around corner		***when tightened all the way, begins to expand and let go around corner

2019-04-20T14:28:23Z

April 20, 2019

← Older revision		Revision as of 14:28, 20 April 2019
Line 29:		Line 29:

	<html><iframe width="560" height="315" src="https://www.youtube.com/embed/1a3OX89F_RE" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>		<html><iframe width="560" height="315" src="https://www.youtube.com/embed/1a3OX89F_RE" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

			Photos - https://drive.google.com/drive/folders/17U--YpRedQejrkIcjDcmEpnYU_NkyCjS?usp=sharing

	==April 19, 2019==		==April 19, 2019==

2019-04-20T14:27:44Z

April 20, 2019

← Older revision		Revision as of 14:27, 20 April 2019
Line 23:		Line 23:
	***need to disassemble and diagnose - sand paper on p2 inserts?		***need to disassemble and diagnose - sand paper on p2 inserts?
	***causing motors to hang up especially bad in certain spots		***causing motors to hang up especially bad in certain spots
			***they dont seem to hang up as bad when machine is spinning ccw, not sure why?

2019-04-20T14:26:10Z

April 20, 2019

← Older revision		Revision as of 14:26, 20 April 2019
Line 24:		Line 24:
	***causing motors to hang up especially bad in certain spots		***causing motors to hang up especially bad in certain spots


			<html><iframe width="560" height="315" src="https://www.youtube.com/embed/y_F94h-HLos" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

			<html><iframe width="560" height="315" src="https://www.youtube.com/embed/1a3OX89F_RE" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>

	==April 19, 2019==		==April 19, 2019==

2019-04-20T14:22:56Z

Log

@@ Line 11: / Line 11: @@
 =Log=
 ==April 19, 2019==
@@ Line 26: / Line 39: @@
 ***change to square nuts for back side, have to dissasemble machine to insert 30mm bolt
 **Need to make nut insert on Z bearing holder a little bigger
 ==April 16, 2019==