User:Dorkmo/Builds/SteamEngine - Revision history

Dorkmo: /* to do */

2014-11-22T01:34:39Z

to do

← Older revision		Revision as of 01:34, 22 November 2014
Line 9:		Line 9:
	calculate desired steam flow through valves http://en.wikipedia.org/wiki/Flow_coefficient		calculate desired steam flow through valves http://en.wikipedia.org/wiki/Flow_coefficient

			*through crank shaft oil line from split pillow block to arm split bearing
			*printable shaft hole alignment jig for 1" holes
			*2 position solenoid valve

	=hardware=		=hardware=

2013-04-12T04:52:40Z

← Older revision		Revision as of 04:52, 12 April 2013
Line 5:		Line 5:
	feel free to make comments in the discussion tab.		feel free to make comments in the discussion tab.

	==hardware==
			=to do=
			calculate desired steam flow through valves http://en.wikipedia.org/wiki/Flow_coefficient


			=hardware=
	*ace hardware		*ace hardware
	:*nylon parts for copper spool		:*nylon parts for copper spool

2013-04-12T04:50:26Z

solenoid

← Older revision		Revision as of 04:50, 12 April 2013
Line 113:		Line 113:

	http://www.ascovalve.com/Applications/Products/Solenoid2WayData.aspx#HotWater		http://www.ascovalve.com/Applications/Products/Solenoid2WayData.aspx#HotWater

			http://en.wikipedia.org/wiki/Flow_coefficient

	==progress==		==progress==

2013-04-08T02:03:17Z

solenoid

← Older revision		Revision as of 02:03, 8 April 2013
Line 111:		Line 111:

	thinking of using a two small 2 position solenoid valves for the in out. mounted with four holes.		thinking of using a two small 2 position solenoid valves for the in out. mounted with four holes.

			http://www.ascovalve.com/Applications/Products/Solenoid2WayData.aspx#HotWater

	==progress==		==progress==

2013-03-30T08:01:59Z

solenoid

← Older revision		Revision as of 08:01, 30 March 2013
Line 109:		Line 109:

	http://www.azom.com/article.aspx?ArticleID=1140		http://www.azom.com/article.aspx?ArticleID=1140

			thinking of using a two small 2 position solenoid valves for the in out. mounted with four holes.

	==progress==		==progress==

2013-01-20T00:32:19Z

design work

← Older revision		Revision as of 00:32, 20 January 2013
Line 22:		Line 22:

	==design work==		==design work==

			====oil====

			[[image:diagram-crankshaftoilpath.jpg]]


	====crank weight====		====crank weight====

2012-05-22T06:51:41Z

progress

← Older revision		Revision as of 06:51, 22 May 2012
Line 269:		Line 269:

	think it might be better to put angle alluminum for the crank arm mount on the piston		think it might be better to put angle alluminum for the crank arm mount on the piston

			5/22/12

			i finished two crank arms. im pretty happy with one but the other the 1 inch side isnt perfectly perpendicular so the other side is off by about half an inch. the piece i used wasnt cut very straight so when i welded it was off. i layed it all out sideways flat and lifted the sheet to the halfway point.

			need to insure proper cut or use different method when welding.

			had to cut into sheet a little to accomidate bolt.
			need to update sketchup.

2012-05-20T18:30:27Z

progress

← Older revision		Revision as of 18:30, 20 May 2012
Line 265:		Line 265:

	should be able to have solenoids hooked to electronics tomorrow		should be able to have solenoids hooked to electronics tomorrow

			5/20/12

			think it might be better to put angle alluminum for the crank arm mount on the piston

2012-05-03T06:52:00Z

progress

← Older revision		Revision as of 06:52, 3 May 2012
Line 256:		Line 256:

	going to cut 3/4 holes for valves in plate		going to cut 3/4 holes for valves in plate

			a little less the 1/2 a square inch area.

	had some drill problems with 1-1/2 holes for crank arms.		had some drill problems with 1-1/2 holes for crank arms.

2012-05-01T06:48:36Z

progress

← Older revision		Revision as of 06:48, 1 May 2012
Line 258:		Line 258:

	had some drill problems with 1-1/2 holes for crank arms.		had some drill problems with 1-1/2 holes for crank arms.

			4/30/12
			need two washers in valve so spring distance be adjusted

			should be able to have solenoids hooked to electronics tomorrow