XM Prusa i3 Procedure - Revision history

Marcin: /* Timing Predictions for a Swarm Build */

2017-03-15T23:22:44Z

Timing Predictions for a Swarm Build

← Older revision		Revision as of 23:22, 15 March 2017
Line 32:		Line 32:
	*'''Prediction after detailed build times are explored:''' 7 hour worst and best case - as we will stick on schedule during the event.		*'''Prediction after detailed build times are explored:''' 7 hour worst and best case - as we will stick on schedule during the event.
	*'''Actual Group Build:'''		*'''Actual Group Build:'''

			[[Category:Folgertech Prusa i3]]

Marcin at 02:36, 25 February 2016

2016-02-25T02:36:04Z

← Older revision		Revision as of 02:36, 25 February 2016
Line 1:		Line 1:
			=Introduction=

	=Presentation=		=Presentation=
	<html><iframe src="https://docs.google.com/presentation/d/1dzDo-2OY_7z2XY2SvImfugWTbrtnAqFGKXdybhAnW40/embed?start=false&loop=false&delayms=3000" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>		<html><iframe src="https://docs.google.com/presentation/d/1dzDo-2OY_7z2XY2SvImfugWTbrtnAqFGKXdybhAnW40/embed?start=false&loop=false&delayms=3000" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>

Marcin: /* Timing Predictions for a Swarm Build */

2016-02-25T02:33:33Z

Timing Predictions for a Swarm Build

← Older revision		Revision as of 02:33, 25 February 2016
Line 28:		Line 28:

	*'''Initial Guess:''' Done, in 8 hours best case including presentations, 12 hours worst case. (8-8 day expected as the "Normal Build Day")		*'''Initial Guess:''' Done, in 8 hours best case including presentations, 12 hours worst case. (8-8 day expected as the "Normal Build Day")
	*'''Prediction after detailed build times are explored:'''		*'''Prediction after detailed build times are explored:''' 7 hour worst and best case - as we will stick on schedule during the event.
	*'''Actual Group Build:'''		*'''Actual Group Build:'''

Marcin at 15:33, 15 February 2016

2016-02-15T15:33:59Z

← Older revision		Revision as of 15:33, 15 February 2016
Line 1:		Line 1:
			=Presentation=
			<html><iframe src="https://docs.google.com/presentation/d/1dzDo-2OY_7z2XY2SvImfugWTbrtnAqFGKXdybhAnW40/embed?start=false&loop=false&delayms=3000" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html>

			=Discussion=

	XM process revolves around leaning out the build so QC is prioritized early on, with as many QC steps frontloaded as possible. This allows steps of lesser importance to be carried out later in the process - allowing for fatigue only later in the day.		XM process revolves around leaning out the build so QC is prioritized early on, with as many QC steps frontloaded as possible. This allows steps of lesser importance to be carried out later in the process - allowing for fatigue only later in the day.

Marcin at 15:16, 15 February 2016

2016-02-15T15:16:30Z

← Older revision		Revision as of 15:16, 15 February 2016
Line 20:		Line 20:
	#Run Calibration Cube.		#Run Calibration Cube.

	Done, in 8 hours best case including presentations, 12 hours worst case. (8-8 day expected as the "Normal Build Day")		=Timing Predictions for a Swarm Build=

			*'''Initial Guess:''' Done, in 8 hours best case including presentations, 12 hours worst case. (8-8 day expected as the "Normal Build Day")
			*'''Prediction after detailed build times are explored:'''
			*'''Actual Group Build:'''

Marcin at 04:09, 6 February 2016

2016-02-06T04:09:53Z

← Older revision		Revision as of 04:09, 6 February 2016
Line 12:		Line 12:
	#Mount extruder and belt.		#Mount extruder and belt.
	#Mount the entire hot bed assembly including rod blocks, at 90 mm from left to the block edge.		#Mount the entire hot bed assembly including rod blocks, at 90 mm from left to the block edge.
			#Mount end stops.
			#Wire the controller. All cable routing/fastening needs to be included here.
			#Wire the power supply.
			#Mount the power supply.
			#Tidy up the wiring, 5 minutes.
			#Boot up Live Linux, or preinstalled software.
			#Run Calibration Cube.

			Done, in 8 hours best case including presentations, 12 hours worst case. (8-8 day expected as the "Normal Build Day")

Marcin at 23:35, 4 February 2016

2016-02-04T23:35:07Z

← Older revision		Revision as of 23:35, 4 February 2016
Line 7:		Line 7:
	#Make frame of 4 2020s plus vertical angles. QC - long pieces front and back, short are superior of the front.		#Make frame of 4 2020s plus vertical angles. QC - long pieces front and back, short are superior of the front.
	#Make x axis. Other team takes y axis, joins z axis team after x axis is done.		#Make x axis. Other team takes y axis, joins z axis team after x axis is done.
	#Add vertical frame. Assemble z flat, then stand it up. Use a standard combination square.		#Add vertical frame. Assemble z flat, then stand it up. Use a standard combination square. Do a preliminary mounting of power supply. Take off the power supply but leave the mounting brackets. (It is more difficult to mount the supply later with other parts in place.
	#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.		#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.
	#Mount the z motors, but not their threaded rods. Slide z motion up and down freely. Tighten one side, parallel to z axis frame, and then let the one tightened side determine the location of the other motor.		#Mount the z motors, but not their threaded rods. Slide z motion up and down freely. Tighten one side, parallel to z axis frame, and then let the one tightened side determine the location of the other motor.
	#Mount extruder and belt.		#Mount extruder and belt.
	#Mount the entire hot bed assembly including rod blocks, at 90 mm from left to the block edge.		#Mount the entire hot bed assembly including rod blocks, at 90 mm from left to the block edge.

Marcin at 23:29, 4 February 2016

2016-02-04T23:29:49Z

← Older revision		Revision as of 23:29, 4 February 2016
Line 6:		Line 6:

	#Make frame of 4 2020s plus vertical angles. QC - long pieces front and back, short are superior of the front.		#Make frame of 4 2020s plus vertical angles. QC - long pieces front and back, short are superior of the front.
			#Make x axis. Other team takes y axis, joins z axis team after x axis is done.
	#Add vertical frame. Assemble z flat, then stand it up. Use a standard combination square.		#Add vertical frame. Assemble z flat, then stand it up. Use a standard combination square.
	#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.		#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.

Marcin at 06:24, 3 February 2016

2016-02-03T06:24:09Z

← Older revision		Revision as of 06:24, 3 February 2016
Line 9:		Line 9:
	#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.		#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.
	#Mount the z motors, but not their threaded rods. Slide z motion up and down freely. Tighten one side, parallel to z axis frame, and then let the one tightened side determine the location of the other motor.		#Mount the z motors, but not their threaded rods. Slide z motion up and down freely. Tighten one side, parallel to z axis frame, and then let the one tightened side determine the location of the other motor.
			#Mount extruder and belt.
			#Mount the entire hot bed assembly including rod blocks, at 90 mm from left to the block edge.

Marcin at 06:22, 3 February 2016

2016-02-03T06:22:38Z

← Older revision		Revision as of 06:22, 3 February 2016
Line 8:		Line 8:
	#Add vertical frame. Assemble z flat, then stand it up. Use a standard combination square.		#Add vertical frame. Assemble z flat, then stand it up. Use a standard combination square.
	#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.		#Mount z rod clamp, mount z rods with x axis on them. Tighten down z rod clamp screws to the base, not to rod.
			#Mount the z motors, but not their threaded rods. Slide z motion up and down freely. Tighten one side, parallel to z axis frame, and then let the one tightened side determine the location of the other motor.