|
|
| Line 1: |
Line 1: |
| <center>'''The Liberator Beta v1.0'''</center>
| | Download Open Document Format (ODF)specifications for The Liberator Beta v1.0 [http://openfarmtech.org/Libspecbetav1.odt here]. |
|
| |
|
| <center>Open Source, High Performance CEB Press</center>
| | [[Image:libspec1.jpg]] |
|
| |
|
| <center>Beta Release Product Information</center>
| | [[Image:libspec2.jpg]] |
|
| |
|
| <center>Factor e Farm, November 3, 2009 </center>
| | [[Image:libspec3.jpg]] |
|
| |
|
| | [[Image:libspec4.jpg]] |
|
| |
|
| | [[Image:libspec5.jpg]] |
|
| |
|
| {| class="prettytable"
| |
| | Model
| |
| | ''The Liberator'' Beta v1.0 Product Release
| |
|
| |
|
| (last version was The Liberator Prototype II<ref name="ftn1">See ''http://openfarmtech.org/weblog/?p=1025''</ref>)
| |
|
| |
| |-
| |
| | Release Status
| |
| | Limited Production, user testing, user co-development
| |
|
| |
| |-
| |
| | License
| |
| | OSE-Post Scarcity Economics (OSE-PSE) License<ref name="ftn2">In progress.</ref> (compatible with CC-BY-SA, GPL for hardware, and OSE Specifications)
| |
|
| |
| |-
| |
| | Press Type
| |
| | Hydraulic, manual, vertical press
| |
|
| |
| |-
| |
| | Production Rates
| |
|
| |
| - with 8 GPM fluid flow<ref name="ftn3"><sup>Using the available Power Cube for testing. At max throttle, the existing system delivers 8 GPM at the workingcylinders.</sup></ref>
| |
|
| |
| - manual control<ref name="ftn4"><sup>Achieved using Power Cube by pressing 4 1/4” x6”x12” blocks in a set of three, timed, 5-block runs. Times achieved were 1 min 24 sec, 1 min 24 sec, and 1 min 10 sec with an unskilled operator.</sup></ref>
| |
|
| |
| - automatic control<ref name="ftn5"><sup>Automatic control pressing rate was determined by measuring repetitive motion times for each cylinder, and averaging over the number of cycles – using an empty hopper and manual controls. This was done to minimize operator dexterity limits of determining automatic control pressing rate, without actually using automatic controls. Brick production rate was determined as the sum of the average full cycle times for each of the two cylinders.</sup></ref>
| |
|
| |
| - with 15 GPM hydraulic flow<ref name="ftn6"><sup>Done by using LifeTrac as a 15 GPM fluid source at medium-high throttle. Manual controls were used to infer production rate as in footnote above. </sup></ref>
| |
| | 4 blocks per minute
| |
|
| |
| 5.5 blocks per minute
| |
|
| |
| 9 blocks per minute
| |
|
| |
| |-
| |
| | Theoretical maximum production rate<ref name="ftn7"><sup>15 GPM flow resulted in a cycle time of under 5 seconds for the large cylinder. We believe that this could be brought down to as little as 3 second per cycle. The full cycle time observed for the secondary cylinder with 8 gpm flow is 2 seconds. Thus, a 5 second overall cycle time is predicted – or 12 bricks per minute. At this rate, the limiting factor are soil loading dynamics of gravity flow, which is assisted by hopper shaking.</sup></ref>
| |
| | 12 blocks per minute
| |
|
| |
| |-
| |
| | Size (LxWxH)
| |
| | 5.5'x5'x8' – fits on a ¾ ton pickup truck bed
| |
|
| |
| |-
| |
| | Special features
| |
| | - open source business model
| |
|
| |
| - Design-for-Disassembly (DfD)
| |
|
| |
| - Design-for-Post-Scarcity (DfPS)
| |
|
| |
| |-
| |
| | Power source
| |
| | Not included<ref name="ftn8"><sup>Any external power source of up to 25 GPM may be used, such as LifeTrac and Power Cube. Tractors and skid loaders are 2 good, mainstream options. Skid loaders typically have 17 GPM auxiliary hydrauilic flow, such as Bobcat40 hp range models (http://www.bobcat.com/historical_specs/skid_steer/s130_2005) up to 34 GPM in the 80 hp models. Gehl 80 hp models have 23-36 GPM auxiliary hydraulics. Sample modern tractors – 45 hp AGCO - 14 GPM - [http://www.tractordata.com/td/003/td3293.html http://www.tractordata.com/td/003/td3293.html] (http://www.gehl.com/const/Product_Detail/prodpgdt_6640E.html#specifications). Case has 20-range GPM ([http://www.gehl.com/const/Product_Detail/prodpgdt_6640E.html#specifications http://www.gehl.com/const/Product_Detail/prodpgdt_6640E.html#specifications]). See other websites for details.</sup></ref>
| |
|
| |
| |-
| |
| | Operating system pressure
| |
| | 2300 psi
| |
|
| |
| |-
| |
| | Cylinders (Bore x Stroke x Rod)
| |
| | 5”x8”x2” main, 2.5”x14”x1” secondary
| |
|
| |
| |-
| |
| | Compression force
| |
| | 23 short tons
| |
|
| |
| |-
| |
| | Block Size
| |
| | 4 1/4”x6”x12”
| |
|
| |
| |-
| |
| | Variability of block thickness<ref name="ftn9"><sup>See thickness data set below for a 25 brick sample. This variability is defined as the standard deviation.</sup></ref>
| |
| | +/-0.1”
| |
|
| |
| |-
| |
| | Materials Cost, Prototype II<ref name="ftn10"><sup>See Bill of Materials elsewhere.</sup></ref>
| |
| | $2902
| |
|
| |
| |-
| |
| | Weight, Prototype II
| |
| | 1922 lb
| |
|
| |
| |-
| |
| | Predicted Materials Cost, Beta v1.0
| |
| | $2095
| |
|
| |
| |-
| |
| | Predicted Weight, The Liberator Beta v1.0
| |
| | 1650 lb
| |
|
| |
| |-
| |
| | Soil requirements, cubic yards per hour:
| |
|
| |
| - 4 blocks per minute<ref name="ftn11"><sup>Assuming each brick weighs 15 pounds, and density of soil is about a ton per cubic yard</sup></ref>
| |
|
| |
| - 9 blocks per minute
| |
| | 2
| |
|
| |
| 4.5
| |
|
| |
| |-
| |
| | Hopper size (LxWxH)
| |
| | 6'x5'x3'
| |
|
| |
| |-
| |
| | Hopper loading
| |
| | Manual, conveyor, or tractor loader, especially LifeTrac Pulverizer-Loader.
| |
|
| |
| |-
| |
| | Grate shaker
| |
| | 1.93 cu in hydraulic motor with 6 lb eccentric hammer
| |
|
| |
| |-
| |
| | Included features
| |
| | Complete CEB machine with hydraulic system (but NO power source); grate, grate shaker, 2-spool manual control valve, hopper extensions, large hopper, user manual; ready to plug into hydraulic source of 12 GPM rated flow
| |
|
| |
| |-
| |
| | Price FOB Kansas City area, Missouri; limited production run of 3 machines
| |
| | - $3500 for True Fans<ref name="ftn12">See openfarmtech.org for True Fans. This special price applies only to those who have signed up during'' The Liberator'' development cycle prior to November 1, 2010 – ie, those people who were instrumental in funding the actual devleopment of ''The Liberator''.</ref>
| |
|
| |
| - $5500 for all others
| |
|
| |
|
| |
|
| |
|
| |
| |-
| |
| | Delivery and assembly options
| |
| | - You pick up the assembled machine yourself or arrange for shipping
| |
|
| |
| - We disassemble, crate, and ship the machine on a pallet (disassembly/crating fee of $300, plus shipping)
| |
|
| |
| - We ship assembled machine by truck freight (no disassembly/crating fee, but shipping may be more expensive)
| |
|
| |
| |-
| |
| | Delivery time
| |
| | 21 day on-demand fabrication time, from receipt of FOB payment in full
| |
|
| |
| |-
| |
| | Options
| |
| | - Pre-purchase of automatic control module - $750. Auto controls module will be real released within approximately 2 months.
| |
|
| |
| - Power Cube hydraulic power source with 17 hp engine - $1500
| |
|
| |
| - Tractor PTO-driven hydraulic power source, 15 GPM - $800
| |
|
| |
| - Trailer for easy transportation - $1000); standard mobility is via forklift carry tubes
| |
|
| |
| - 12 GPM Quick Couplers to all cylinders and motors - $250<ref name="ftn13"><sup>Allows easier storage and setup, but limits flow rate compared to hard-wiring, which supports up to 25 gpm flow)</sup></ref>
| |
|
| |
| - Up to 24 gpm Quick Coupler flow connection into main valve -$200<ref name="ftn14"><sup>1” flush-face coupler s allow up to 26 GPM flow - http://www.hofmannfluidpower.com/hydraulic_couplings/flush-face-series.htm </sup></ref>
| |
|
| |
| - Pressure relief valve – $50
| |
|
| |
| - Needle valve flow reducer, 0-25 GPM - $60
| |
|
| |
| - On-demand customization
| |
|
| |
| - Spare abrasion liners – to be determined upon more complete abrasion requirements, but materials cost for each linear are low at about $5-10
| |
|
| |
| - Lifetime Warranty - $4000<ref name="ftn15">This is a Beta Release for testing performance. You should read the blog posts, OSE project management site on Open Pario, and other supporting information to understand the state of development. The initial release will be a fully-functioning machine, it will still require a number of optimizations, to streamline both the operational aspects of the machine and the fabrication procedure. This is because a product evolves over time to a stable release, and even then, upgrades and customizations can be made. You are purchasing the Beta Release to support our development (cont.) process. We offer the Lifetime Warranty if you would like to exchange your machine in the future for the latest stable product release, if you deem that desirable. In that case, we ask you to bring your old machine back to the Factor e, and we will exchange it for the latest version. This allows us to salvage valuable parts, and it allows you to have the final, lifetime-service product. Both parties win by helping the open source development process arrive at a stable release as quickly as possible. All money invested into the project goes back into continuing product development. You have a limit of one exchange, and you may choose not to use it if you are satisfied with the Beta Version 1.0. You are expected to pay cover the transportation costs for returning your old machine and shipping the new.</ref>
| |
|
| |
| |-
| |
| | Future developments
| |
| | - Automatic control module retrofit
| |
|
| |
| - Brick roller conveyors, 10' sections
| |
|
| |
| - Soil testing kit
| |
|
| |
| - Open source house plans
| |
|
| |
| - Fabricator training
| |
|
| |
| - Fabrication optimization, CAD, CAM digital fabrication files
| |
|
| |
| |-
| |
| | Warranty
| |
| | DfD design and ready replacement of parts constitute our guarantee of long service.<ref name="ftn16"><sup>All parts are replaceable and easily obtainable, and the DfD allows for quick service. Wearable parts (compression chamber liners) are to be replaced depending on the usage of the machine.. The machine is guaranteed to be free from any defects. Wearable parts are the responsibility of the user. Liner replacements cost about $5 each for materials, and there are 8 liner parts. Each liner should last for about 20,000 bricks pressed. Hydraulic seals may have to be replaced every 5-10 years.</sup></ref> See the Lifetime Warranty under Options above.
| |
|
| |
| |}
| |
| Brick thickness detail including standard deviation
| |
|
| |
|
| |
|
| |
|
| |
| ----
| |
| <references/>
| |
|
| |
|
| [[Category:CEB]][[Category:Product Release]] | | [[Category:CEB]][[Category:Product Release]] |
